[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Errata] [Info page]

Obsoleted by: 8200 DRAFT STANDARD
Updated by: 5095, 5722, 5871, 6437, 6564, 6935, 6946,
Network Working Group                                         S. Deering
Request for Comments: 2460                                         Cisco
Obsoletes: 1883                                                R. Hinden
Category: Standards Track                                          Nokia
                                                           December 1998


                  Internet Protocol, Version 6 (IPv6)
                             Specification

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (1998).  All Rights Reserved.

Abstract

   This document specifies version 6 of the Internet Protocol (IPv6),
   also sometimes referred to as IP Next Generation or IPng.

Table of Contents

   1. Introduction..................................................2
   2. Terminology...................................................3
   3. IPv6 Header Format............................................4
   4. IPv6 Extension Headers........................................6
       4.1 Extension Header Order...................................7
       4.2 Options..................................................9
       4.3 Hop-by-Hop Options Header...............................11
       4.4 Routing Header..........................................12
       4.5 Fragment Header.........................................18
       4.6 Destination Options Header..............................23
       4.7 No Next Header..........................................24
   5. Packet Size Issues...........................................24
   6. Flow Labels..................................................25
   7. Traffic Classes..............................................25
   8. Upper-Layer Protocol Issues..................................27
       8.1 Upper-Layer Checksums...................................27
       8.2 Maximum Packet Lifetime.................................28
       8.3 Maximum Upper-Layer Payload Size........................28
       8.4 Responding to Packets Carrying Routing Headers..........29



Deering & Hinden            Standards Track                     [Page 1]


RFC 2460                   IPv6 Specification              December 1998


   Appendix A. Semantics and Usage of the Flow Label Field.........30
   Appendix B. Formatting Guidelines for Options...................32
   Security Considerations.........................................35
   Acknowledgments.................................................35
   Authors' Addresses..............................................35
   References......................................................35
   Changes Since RFC-1883..........................................36
   Full Copyright Statement........................................39

1.  Introduction

   IP version 6 (IPv6) is a new version of the Internet Protocol,
   designed as the successor to IP version 4 (IPv4) [RFC-791].  The
   changes from IPv4 to IPv6 fall primarily into the following
   categories:

      o  Expanded Addressing Capabilities

         IPv6 increases the IP address size from 32 bits to 128 bits, to
         support more levels of addressing hierarchy, a much greater
         number of addressable nodes, and simpler auto-configuration of
         addresses.  The scalability of multicast routing is improved by
         adding a "scope" field to multicast addresses.  And a new type
         of address called an "anycast address" is defined, used to send
         a packet to any one of a group of nodes.

      o  Header Format Simplification

         Some IPv4 header fields have been dropped or made optional, to
         reduce the common-case processing cost of packet handling and
         to limit the bandwidth cost of the IPv6 header.

      o  Improved Support for Extensions and Options

         Changes in the way IP header options are encoded allows for
         more efficient forwarding, less stringent limits on the length
         of options, and greater flexibility for introducing new options
         in the future.

      o  Flow Labeling Capability

         A new capability is added to enable the labeling of packets
         belonging to particular traffic "flows" for which the sender
         requests special handling, such as non-default quality of
         service or "real-time" service.






Deering & Hinden            Standards Track                     [Page 2]


RFC 2460                   IPv6 Specification              December 1998


      o  Authentication and Privacy Capabilities

         Extensions to support authentication, data integrity, and
         (optional) data confidentiality are specified for IPv6.

   This document specifies the basic IPv6 header and the initially-
   defined IPv6 extension headers and options.  It also discusses packet
   size issues, the semantics of flow labels and traffic classes, and
   the effects of IPv6 on upper-layer protocols.  The format and
   semantics of IPv6 addresses are specified separately in [ADDRARCH].
   The IPv6 version of ICMP, which all IPv6 implementations are required
   to include, is specified in [ICMPv6].

2.  Terminology

   node        - a device that implements IPv6.

   router      - a node that forwards IPv6 packets not explicitly
                 addressed to itself.  [See Note below].

   host        - any node that is not a router.  [See Note below].

   upper layer - a protocol layer immediately above IPv6.  Examples are
                 transport protocols such as TCP and UDP, control
                 protocols such as ICMP, routing protocols such as OSPF,
                 and internet or lower-layer protocols being "tunneled"
                 over (i.e., encapsulated in) IPv6 such as IPX,
                 AppleTalk, or IPv6 itself.

   link        - a communication facility or medium over which nodes can
                 communicate at the link layer, i.e., the layer
                 immediately below IPv6.  Examples are Ethernets (simple
                 or bridged); PPP links; X.25, Frame Relay, or ATM
                 networks; and internet (or higher) layer "tunnels",
                 such as tunnels over IPv4 or IPv6 itself.

   neighbors   - nodes attached to the same link.

   interface   - a node's attachment to a link.

   address     - an IPv6-layer identifier for an interface or a set of
                 interfaces.

   packet      - an IPv6 header plus payload.

   link MTU    - the maximum transmission unit, i.e., maximum packet
                 size in octets, that can be conveyed over a link.




Deering & Hinden            Standards Track                     [Page 3]


RFC 2460                   IPv6 Specification              December 1998


   path MTU    - the minimum link MTU of all the links in a path between
                 a source node and a destination node.

   Note: it is possible, though unusual, for a device with multiple
   interfaces to be configured to forward non-self-destined packets
   arriving from some set (fewer than all) of its interfaces, and to
   discard non-self-destined packets arriving from its other interfaces.
   Such a device must obey the protocol requirements for routers when
   receiving packets from, and interacting with neighbors over, the
   former (forwarding) interfaces.  It must obey the protocol
   requirements for hosts when receiving packets from, and interacting
   with neighbors over, the latter (non-forwarding) interfaces.

3.  IPv6 Header Format

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |Version| Traffic Class |           Flow Label                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |         Payload Length        |  Next Header  |   Hop Limit   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   |                                                               |
   +                         Source Address                        +
   |                                                               |
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   |                                                               |
   +                      Destination Address                      +
   |                                                               |
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Version              4-bit Internet Protocol version number = 6.

   Traffic Class        8-bit traffic class field.  See section 7.

   Flow Label           20-bit flow label.  See section 6.

   Payload Length       16-bit unsigned integer.  Length of the IPv6
                        payload, i.e., the rest of the packet following
                        this IPv6 header, in octets.  (Note that any





Deering & Hinden            Standards Track                     [Page 4]


RFC 2460                   IPv6 Specification              December 1998


                        extension headers [section 4] present are
                        considered part of the payload, i.e., included
                        in the length count.)

   Next Header          8-bit selector.  Identifies the type of header
                        immediately following the IPv6 header.  Uses the
                        same values as the IPv4 Protocol field [RFC-1700
                        et seq.].

   Hop Limit            8-bit unsigned integer.  Decremented by 1 by
                        each node that forwards the packet. The packet
                        is discarded if Hop Limit is decremented to
                        zero.

   Source Address       128-bit address of the originator of the packet.
                        See [ADDRARCH].

   Destination Address  128-bit address of the intended recipient of the
                        packet (possibly not the ultimate recipient, if
                        a Routing header is present).  See [ADDRARCH]
                        and section 4.4.






























Deering & Hinden            Standards Track                     [Page 5]


RFC 2460                   IPv6 Specification              December 1998


4.  IPv6 Extension Headers

   In IPv6, optional internet-layer information is encoded in separate
   headers that may be placed between the IPv6 header and the upper-
   layer header in a packet.  There are a small number of such extension
   headers, each identified by a distinct Next Header value.  As
   illustrated in these examples, an IPv6 packet may carry zero, one, or
   more extension headers, each identified by the Next Header field of
   the preceding header:

   +---------------+------------------------
   |  IPv6 header  | TCP header + data
   |               |
   | Next Header = |
   |      TCP      |
   +---------------+------------------------


   +---------------+----------------+------------------------
   |  IPv6 header  | Routing header | TCP header + data
   |               |                |
   | Next Header = |  Next Header = |
   |    Routing    |      TCP       |
   +---------------+----------------+------------------------


   +---------------+----------------+-----------------+-----------------
   |  IPv6 header  | Routing header | Fragment header | fragment of TCP
   |               |                |                 |  header + data
   | Next Header = |  Next Header = |  Next Header =  |
   |    Routing    |    Fragment    |       TCP       |
   +---------------+----------------+-----------------+-----------------

   With one exception, extension headers are not examined or processed
   by any node along a packet's delivery path, until the packet reaches
   the node (or each of the set of nodes, in the case of multicast)
   identified in the Destination Address field of the IPv6 header.
   There, normal demultiplexing on the Next Header field of the IPv6
   header invokes the module to process the first extension header, or
   the upper-layer header if no extension header is present.  The
   contents and semantics of each extension header determine whether or
   not to proceed to the next header.  Therefore, extension headers must
   be processed strictly in the order they appear in the packet; a
   receiver must not, for example, scan through a packet looking for a
   particular kind of extension header and process that header prior to
   processing all preceding ones.





Deering & Hinden            Standards Track                     [Page 6]


RFC 2460                   IPv6 Specification              December 1998


   The exception referred to in the preceding paragraph is the Hop-by-
   Hop Options header, which carries information that must be examined
   and processed by every node along a packet's delivery path, including
   the source and destination nodes.  The Hop-by-Hop Options header,
   when present, must immediately follow the IPv6 header.  Its presence
   is indicated by the value zero in the Next Header field of the IPv6
   header.

   If, as a result of processing a header, a node is required to proceed
   to the next header but the Next Header value in the current header is
   unrecognized by the node, it should discard the packet and send an
   ICMP Parameter Problem message to the source of the packet, with an
   ICMP Code value of 1 ("unrecognized Next Header type encountered")
   and the ICMP Pointer field containing the offset of the unrecognized
   value within the original packet.  The same action should be taken if
   a node encounters a Next Header value of zero in any header other
   than an IPv6 header.

   Each extension header is an integer multiple of 8 octets long, in
   order to retain 8-octet alignment for subsequent headers.  Multi-
   octet fields within each extension header are aligned on their
   natural boundaries, i.e., fields of width n octets are placed at an
   integer multiple of n octets from the start of the header, for n = 1,
   2, 4, or 8.

   A full implementation of IPv6 includes implementation of the
   following extension headers:

           Hop-by-Hop Options
           Routing (Type 0)
           Fragment
           Destination Options
           Authentication
           Encapsulating Security Payload

   The first four are specified in this document; the last two are
   specified in [RFC-2402] and [RFC-2406], respectively.

4.1  Extension Header Order

   When more than one extension header is used in the same packet, it is
   recommended that those headers appear in the following order:

           IPv6 header
           Hop-by-Hop Options header
           Destination Options header (note 1)
           Routing header
           Fragment header



Deering & Hinden            Standards Track                     [Page 7]


RFC 2460                   IPv6 Specification              December 1998


           Authentication header (note 2)
           Encapsulating Security Payload header (note 2)
           Destination Options header (note 3)
           upper-layer header

           note 1: for options to be processed by the first destination
                   that appears in the IPv6 Destination Address field
                   plus subsequent destinations listed in the Routing
                   header.

           note 2: additional recommendations regarding the relative
                   order of the Authentication and Encapsulating
                   Security Payload headers are given in [RFC-2406].

           note 3: for options to be processed only by the final
                   destination of the packet.

   Each extension header should occur at most once, except for the
   Destination Options header which should occur at most twice (once
   before a Routing header and once before the upper-layer header).

   If the upper-layer header is another IPv6 header (in the case of IPv6
   being tunneled over or encapsulated in IPv6), it may be followed by
   its own extension headers, which are separately subject to the same
   ordering recommendations.

   If and when other extension headers are defined, their ordering
   constraints relative to the above listed headers must be specified.

   IPv6 nodes must accept and attempt to process extension headers in
   any order and occurring any number of times in the same packet,
   except for the Hop-by-Hop Options header which is restricted to
   appear immediately after an IPv6 header only.  Nonetheless, it is
   strongly advised that sources of IPv6 packets adhere to the above
   recommended order until and unless subsequent specifications revise
   that recommendation.















Deering & Hinden            Standards Track                     [Page 8]


RFC 2460                   IPv6 Specification              December 1998


4.2  Options

   Two of the currently-defined extension headers -- the Hop-by-Hop
   Options header and the Destination Options header -- carry a variable
   number of type-length-value (TLV) encoded "options", of the following
   format:

      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- - - - - - - - -
      |  Option Type  |  Opt Data Len |  Option Data
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- - - - - - - - -

      Option Type          8-bit identifier of the type of option.

      Opt Data Len         8-bit unsigned integer.  Length of the Option
                           Data field of this option, in octets.

      Option Data          Variable-length field.  Option-Type-specific
                           data.

   The sequence of options within a header must be processed strictly in
   the order they appear in the header; a receiver must not, for
   example, scan through the header looking for a particular kind of
   option and process that option prior to processing all preceding
   ones.

   The Option Type identifiers are internally encoded such that their
   highest-order two bits specify the action that must be taken if the
   processing IPv6 node does not recognize the Option Type:

      00 - skip over this option and continue processing the header.

      01 - discard the packet.

      10 - discard the packet and, regardless of whether or not the
           packet's Destination Address was a multicast address, send an
           ICMP Parameter Problem, Code 2, message to the packet's
           Source Address, pointing to the unrecognized Option Type.

      11 - discard the packet and, only if the packet's Destination
           Address was not a multicast address, send an ICMP Parameter
           Problem, Code 2, message to the packet's Source Address,
           pointing to the unrecognized Option Type.

   The third-highest-order bit of the Option Type specifies whether or
   not the Option Data of that option can change en-route to the
   packet's final destination.  When an Authentication header is present





Deering & Hinden            Standards Track                     [Page 9]


RFC 2460                   IPv6 Specification              December 1998


   in the packet, for any option whose data may change en-route, its
   entire Option Data field must be treated as zero-valued octets when
   computing or verifying the packet's authenticating value.

      0 - Option Data does not change en-route

      1 - Option Data may change en-route

   The three high-order bits described above are to be treated as part
   of the Option Type, not independent of the Option Type.  That is, a
   particular option is identified by a full 8-bit Option Type, not just
   the low-order 5 bits of an Option Type.

   The same Option Type numbering space is used for both the Hop-by-Hop
   Options header and the Destination Options header.  However, the
   specification of a particular option may restrict its use to only one
   of those two headers.

   Individual options may have specific alignment requirements, to
   ensure that multi-octet values within Option Data fields fall on
   natural boundaries.  The alignment requirement of an option is
   specified using the notation xn+y, meaning the Option Type must
   appear at an integer multiple of x octets from the start of the
   header, plus y octets.  For example:

      2n    means any 2-octet offset from the start of the header.
      8n+2  means any 8-octet offset from the start of the header,
            plus 2 octets.

   There are two padding options which are used when necessary to align
   subsequent options and to pad out the containing header to a multiple
   of 8 octets in length.  These padding options must be recognized by
   all IPv6 implementations:

   Pad1 option  (alignment requirement: none)

      +-+-+-+-+-+-+-+-+
      |       0       |
      +-+-+-+-+-+-+-+-+

      NOTE! the format of the Pad1 option is a special case -- it does
            not have length and value fields.

      The Pad1 option is used to insert one octet of padding into the
      Options area of a header.  If more than one octet of padding is
      required, the PadN option, described next, should be used, rather
      than multiple Pad1 options.




Deering & Hinden            Standards Track                    [Page 10]


RFC 2460                   IPv6 Specification              December 1998


   PadN option  (alignment requirement: none)

      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- - - - - - - - -
      |       1       |  Opt Data Len |  Option Data
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- - - - - - - - -

      The PadN option is used to insert two or more octets of padding
      into the Options area of a header.  For N octets of padding, the
      Opt Data Len field contains the value N-2, and the Option Data
      consists of N-2 zero-valued octets.

   Appendix B contains formatting guidelines for designing new options.

4.3  Hop-by-Hop Options Header

   The Hop-by-Hop Options header is used to carry optional information
   that must be examined by every node along a packet's delivery path.
   The Hop-by-Hop Options header is identified by a Next Header value of
   0 in the IPv6 header, and has the following format:

    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  Next Header  |  Hdr Ext Len  |                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+                               +
    |                                                               |
    .                                                               .
    .                            Options                            .
    .                                                               .
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Next Header          8-bit selector.  Identifies the type of header
                        immediately following the Hop-by-Hop Options
                        header.  Uses the same values as the IPv4
                        Protocol field [RFC-1700 et seq.].

   Hdr Ext Len          8-bit unsigned integer.  Length of the Hop-by-
                        Hop Options header in 8-octet units, not
                        including the first 8 octets.

   Options              Variable-length field, of length such that the
                        complete Hop-by-Hop Options header is an integer
                        multiple of 8 octets long.  Contains one or more
                        TLV-encoded options, as described in section
                        4.2.

   The only hop-by-hop options defined in this document are the Pad1 and
   PadN options specified in section 4.2.




Deering & Hinden            Standards Track                    [Page 11]


RFC 2460                   IPv6 Specification              December 1998


4.4  Routing Header

   The Routing header is used by an IPv6 source to list one or more
   intermediate nodes to be "visited" on the way to a packet's
   destination.  This function is very similar to IPv4's Loose Source
   and Record Route option.  The Routing header is identified by a Next
   Header value of 43 in the immediately preceding header, and has the
   following format:

    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  Next Header  |  Hdr Ext Len  |  Routing Type | Segments Left |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    .                                                               .
    .                       type-specific data                      .
    .                                                               .
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Next Header          8-bit selector.  Identifies the type of header
                        immediately following the Routing header.  Uses
                        the same values as the IPv4 Protocol field
                        [RFC-1700 et seq.].

   Hdr Ext Len          8-bit unsigned integer.  Length of the Routing
                        header in 8-octet units, not including the first
                        8 octets.

   Routing Type         8-bit identifier of a particular Routing header
                        variant.

   Segments Left        8-bit unsigned integer.  Number of route
                        segments remaining, i.e., number of explicitly
                        listed intermediate nodes still to be visited
                        before reaching the final destination.

   type-specific data   Variable-length field, of format determined by
                        the Routing Type, and of length such that the
                        complete Routing header is an integer multiple
                        of 8 octets long.

   If, while processing a received packet, a node encounters a Routing
   header with an unrecognized Routing Type value, the required behavior
   of the node depends on the value of the Segments Left field, as
   follows:






Deering & Hinden            Standards Track                    [Page 12]


RFC 2460                   IPv6 Specification              December 1998


      If Segments Left is zero, the node must ignore the Routing header
      and proceed to process the next header in the packet, whose type
      is identified by the Next Header field in the Routing header.

      If Segments Left is non-zero, the node must discard the packet and
      send an ICMP Parameter Problem, Code 0, message to the packet's
      Source Address, pointing to the unrecognized Routing Type.

   If, after processing a Routing header of a received packet, an
   intermediate node determines that the packet is to be forwarded onto
   a link whose link MTU is less than the size of the packet, the node
   must discard the packet and send an ICMP Packet Too Big message to
   the packet's Source Address.






































Deering & Hinden            Standards Track                    [Page 13]


RFC 2460                   IPv6 Specification              December 1998


   The Type 0 Routing header has the following format:

    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  Next Header  |  Hdr Ext Len  | Routing Type=0| Segments Left |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                            Reserved                           |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    +                                                               +
    |                                                               |
    +                           Address[1]                          +
    |                                                               |
    +                                                               +
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    +                                                               +
    |                                                               |
    +                           Address[2]                          +
    |                                                               |
    +                                                               +
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    .                               .                               .
    .                               .                               .
    .                               .                               .
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    +                                                               +
    |                                                               |
    +                           Address[n]                          +
    |                                                               |
    +                                                               +
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Next Header          8-bit selector.  Identifies the type of header
                        immediately following the Routing header.  Uses
                        the same values as the IPv4 Protocol field
                        [RFC-1700 et seq.].

   Hdr Ext Len          8-bit unsigned integer.  Length of the Routing
                        header in 8-octet units, not including the first
                        8 octets.  For the Type 0 Routing header, Hdr
                        Ext Len is equal to two times the number of
                        addresses in the header.

   Routing Type         0.



Deering & Hinden            Standards Track                    [Page 14]


RFC 2460                   IPv6 Specification              December 1998


   Segments Left        8-bit unsigned integer.  Number of route
                        segments remaining, i.e., number of explicitly
                        listed intermediate nodes still to be visited
                        before reaching the final destination.

   Reserved             32-bit reserved field.  Initialized to zero for
                        transmission; ignored on reception.

   Address[1..n]        Vector of 128-bit addresses, numbered 1 to n.

   Multicast addresses must not appear in a Routing header of Type 0, or
   in the IPv6 Destination Address field of a packet carrying a Routing
   header of Type 0.

   A Routing header is not examined or processed until it reaches the
   node identified in the Destination Address field of the IPv6 header.
   In that node, dispatching on the Next Header field of the immediately
   preceding header causes the Routing header module to be invoked,
   which, in the case of Routing Type 0, performs the following
   algorithm:































Deering & Hinden            Standards Track                    [Page 15]


RFC 2460                   IPv6 Specification              December 1998


   if Segments Left = 0 {
      proceed to process the next header in the packet, whose type is
      identified by the Next Header field in the Routing header
   }
   else if Hdr Ext Len is odd {
         send an ICMP Parameter Problem, Code 0, message to the Source
         Address, pointing to the Hdr Ext Len field, and discard the
         packet
   }
   else {
      compute n, the number of addresses in the Routing header, by
      dividing Hdr Ext Len by 2

      if Segments Left is greater than n {
         send an ICMP Parameter Problem, Code 0, message to the Source
         Address, pointing to the Segments Left field, and discard the
         packet
      }
      else {
         decrement Segments Left by 1;
         compute i, the index of the next address to be visited in
         the address vector, by subtracting Segments Left from n

         if Address [i] or the IPv6 Destination Address is multicast {
            discard the packet
         }
         else {
            swap the IPv6 Destination Address and Address[i]

            if the IPv6 Hop Limit is less than or equal to 1 {
               send an ICMP Time Exceeded -- Hop Limit Exceeded in
               Transit message to the Source Address and discard the
               packet
            }
            else {
               decrement the Hop Limit by 1

               resubmit the packet to the IPv6 module for transmission
               to the new destination
            }
         }
      }
   }








Deering & Hinden            Standards Track                    [Page 16]


RFC 2460                   IPv6 Specification              December 1998


   As an example of the effects of the above algorithm, consider the
   case of a source node S sending a packet to destination node D, using
   a Routing header to cause the packet to be routed via intermediate
   nodes I1, I2, and I3.  The values of the relevant IPv6 header and
   Routing header fields on each segment of the delivery path would be
   as follows:

   As the packet travels from S to I1:

        Source Address = S                  Hdr Ext Len = 6
        Destination Address = I1            Segments Left = 3
                                            Address[1] = I2
                                            Address[2] = I3
                                            Address[3] = D

   As the packet travels from I1 to I2:

        Source Address = S                  Hdr Ext Len = 6
        Destination Address = I2            Segments Left = 2
                                            Address[1] = I1
                                            Address[2] = I3
                                            Address[3] = D

   As the packet travels from I2 to I3:

        Source Address = S                  Hdr Ext Len = 6
        Destination Address = I3            Segments Left = 1
                                            Address[1] = I1
                                            Address[2] = I2
                                            Address[3] = D

   As the packet travels from I3 to D:

        Source Address = S                  Hdr Ext Len = 6
        Destination Address = D             Segments Left = 0
                                            Address[1] = I1
                                            Address[2] = I2
                                            Address[3] = I3













Deering & Hinden            Standards Track                    [Page 17]


RFC 2460                   IPv6 Specification              December 1998


4.5  Fragment Header

   The Fragment header is used by an IPv6 source to send a packet larger
   than would fit in the path MTU to its destination.  (Note: unlike
   IPv4, fragmentation in IPv6 is performed only by source nodes, not by
   routers along a packet's delivery path -- see section 5.)  The
   Fragment header is identified by a Next Header value of 44 in the
   immediately preceding header, and has the following format:

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  Next Header  |   Reserved    |      Fragment Offset    |Res|M|
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         Identification                        |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Next Header          8-bit selector.  Identifies the initial header
                        type of the Fragmentable Part of the original
                        packet (defined below).  Uses the same values as
                        the IPv4 Protocol field [RFC-1700 et seq.].

   Reserved             8-bit reserved field.  Initialized to zero for
                        transmission; ignored on reception.

   Fragment Offset      13-bit unsigned integer.  The offset, in 8-octet
                        units, of the data following this header,
                        relative to the start of the Fragmentable Part
                        of the original packet.

   Res                  2-bit reserved field.  Initialized to zero for
                        transmission; ignored on reception.

   M flag               1 = more fragments; 0 = last fragment.

   Identification       32 bits.  See description below.

   In order to send a packet that is too large to fit in the MTU of the
   path to its destination, a source node may divide the packet into
   fragments and send each fragment as a separate packet, to be
   reassembled at the receiver.

   For every packet that is to be fragmented, the source node generates
   an Identification value. The Identification must be different than
   that of any other fragmented packet sent recently* with the same
   Source Address and Destination Address.  If a Routing header is
   present, the Destination Address of concern is that of the final
   destination.





Deering & Hinden            Standards Track                    [Page 18]


RFC 2460                   IPv6 Specification              December 1998


      * "recently" means within the maximum likely lifetime of a packet,
        including transit time from source to destination and time spent
        awaiting reassembly with other fragments of the same packet.
        However, it is not required that a source node know the maximum
        packet lifetime.  Rather, it is assumed that the requirement can
        be met by maintaining the Identification value as a simple, 32-
        bit, "wrap-around" counter, incremented each time a packet must
        be fragmented.  It is an implementation choice whether to
        maintain a single counter for the node or multiple counters,
        e.g., one for each of the node's possible source addresses, or
        one for each active (source address, destination address)
        combination.

   The initial, large, unfragmented packet is referred to as the
   "original packet", and it is considered to consist of two parts, as
   illustrated:

   original packet:

   +------------------+----------------------//-----------------------+
   |  Unfragmentable  |                 Fragmentable                  |
   |       Part       |                     Part                      |
   +------------------+----------------------//-----------------------+

      The Unfragmentable Part consists of the IPv6 header plus any
      extension headers that must be processed by nodes en route to the
      destination, that is, all headers up to and including the Routing
      header if present, else the Hop-by-Hop Options header if present,
      else no extension headers.

      The Fragmentable Part consists of the rest of the packet, that is,
      any extension headers that need be processed only by the final
      destination node(s), plus the upper-layer header and data.

   The Fragmentable Part of the original packet is divided into
   fragments, each, except possibly the last ("rightmost") one, being an
   integer multiple of 8 octets long.  The fragments are transmitted in
   separate "fragment packets" as illustrated:

   original packet:

   +------------------+--------------+--------------+--//--+----------+
   |  Unfragmentable  |    first     |    second    |      |   last   |
   |       Part       |   fragment   |   fragment   | .... | fragment |
   +------------------+--------------+--------------+--//--+----------+






Deering & Hinden            Standards Track                    [Page 19]


RFC 2460                   IPv6 Specification              December 1998


   fragment packets:

   +------------------+--------+--------------+
   |  Unfragmentable  |Fragment|    first     |
   |       Part       | Header |   fragment   |
   +------------------+--------+--------------+

   +------------------+--------+--------------+
   |  Unfragmentable  |Fragment|    second    |
   |       Part       | Header |   fragment   |
   +------------------+--------+--------------+
                         o
                         o
                         o
   +------------------+--------+----------+
   |  Unfragmentable  |Fragment|   last   |
   |       Part       | Header | fragment |
   +------------------+--------+----------+

   Each fragment packet is composed of:

      (1) The Unfragmentable Part of the original packet, with the
          Payload Length of the original IPv6 header changed to contain
          the length of this fragment packet only (excluding the length
          of the IPv6 header itself), and the Next Header field of the
          last header of the Unfragmentable Part changed to 44.

      (2) A Fragment header containing:

               The Next Header value that identifies the first header of
               the Fragmentable Part of the original packet.

               A Fragment Offset containing the offset of the fragment,
               in 8-octet units, relative to the start of the
               Fragmentable Part of the original packet.  The Fragment
               Offset of the first ("leftmost") fragment is 0.

               An M flag value of 0 if the fragment is the last
               ("rightmost") one, else an M flag value of 1.

               The Identification value generated for the original
               packet.

      (3) The fragment itself.

   The lengths of the fragments must be chosen such that the resulting
   fragment packets fit within the MTU of the path to the packets'
   destination(s).



Deering & Hinden            Standards Track                    [Page 20]


RFC 2460                   IPv6 Specification              December 1998


   At the destination, fragment packets are reassembled into their
   original, unfragmented form, as illustrated:

   reassembled original packet:

   +------------------+----------------------//------------------------+
   |  Unfragmentable  |                 Fragmentable                   |
   |       Part       |                     Part                       |
   +------------------+----------------------//------------------------+

   The following rules govern reassembly:

      An original packet is reassembled only from fragment packets that
      have the same Source Address, Destination Address, and Fragment
      Identification.

      The Unfragmentable Part of the reassembled packet consists of all
      headers up to, but not including, the Fragment header of the first
      fragment packet (that is, the packet whose Fragment Offset is
      zero), with the following two changes:

         The Next Header field of the last header of the Unfragmentable
         Part is obtained from the Next Header field of the first
         fragment's Fragment header.

         The Payload Length of the reassembled packet is computed from
         the length of the Unfragmentable Part and the length and offset
         of the last fragment.  For example, a formula for computing the
         Payload Length of the reassembled original packet is:

           PL.orig = PL.first - FL.first - 8 + (8 * FO.last) + FL.last

           where
           PL.orig  = Payload Length field of reassembled packet.
           PL.first = Payload Length field of first fragment packet.
           FL.first = length of fragment following Fragment header of
                      first fragment packet.
           FO.last  = Fragment Offset field of Fragment header of
                      last fragment packet.
           FL.last  = length of fragment following Fragment header of
                      last fragment packet.

      The Fragmentable Part of the reassembled packet is constructed
      from the fragments following the Fragment headers in each of the
      fragment packets.  The length of each fragment is computed by
      subtracting from the packet's Payload Length the length of the





Deering & Hinden            Standards Track                    [Page 21]


RFC 2460                   IPv6 Specification              December 1998


      headers between the IPv6 header and fragment itself; its relative
      position in Fragmentable Part is computed from its Fragment Offset
      value.

      The Fragment header is not present in the final, reassembled
      packet.

   The following error conditions may arise when reassembling fragmented
   packets:

      If insufficient fragments are received to complete reassembly of a
      packet within 60 seconds of the reception of the first-arriving
      fragment of that packet, reassembly of that packet must be
      abandoned and all the fragments that have been received for that
      packet must be discarded.  If the first fragment (i.e., the one
      with a Fragment Offset of zero) has been received, an ICMP Time
      Exceeded -- Fragment Reassembly Time Exceeded message should be
      sent to the source of that fragment.

      If the length of a fragment, as derived from the fragment packet's
      Payload Length field, is not a multiple of 8 octets and the M flag
      of that fragment is 1, then that fragment must be discarded and an
      ICMP Parameter Problem, Code 0, message should be sent to the
      source of the fragment, pointing to the Payload Length field of
      the fragment packet.

      If the length and offset of a fragment are such that the Payload
      Length of the packet reassembled from that fragment would exceed
      65,535 octets, then that fragment must be discarded and an ICMP
      Parameter Problem, Code 0, message should be sent to the source of
      the fragment, pointing to the Fragment Offset field of the
      fragment packet.

   The following conditions are not expected to occur, but are not
   considered errors if they do:

      The number and content of the headers preceding the Fragment
      header of different fragments of the same original packet may
      differ.  Whatever headers are present, preceding the Fragment
      header in each fragment packet, are processed when the packets
      arrive, prior to queueing the fragments for reassembly.  Only
      those headers in the Offset zero fragment packet are retained in
      the reassembled packet.

      The Next Header values in the Fragment headers of different
      fragments of the same original packet may differ.  Only the value
      from the Offset zero fragment packet is used for reassembly.




Deering & Hinden            Standards Track                    [Page 22]


RFC 2460                   IPv6 Specification              December 1998


4.6  Destination Options Header

   The Destination Options header is used to carry optional information
   that need be examined only by a packet's destination node(s).  The
   Destination Options header is identified by a Next Header value of 60
   in the immediately preceding header, and has the following format:

    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  Next Header  |  Hdr Ext Len  |                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+                               +
    |                                                               |
    .                                                               .
    .                            Options                            .
    .                                                               .
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Next Header          8-bit selector.  Identifies the type of header
                        immediately following the Destination Options
                        header.  Uses the same values as the IPv4
                        Protocol field [RFC-1700 et seq.].

   Hdr Ext Len          8-bit unsigned integer.  Length of the
                        Destination Options header in 8-octet units, not
                        including the first 8 octets.

   Options              Variable-length field, of length such that the
                        complete Destination Options header is an
                        integer multiple of 8 octets long.  Contains one
                        or  more TLV-encoded options, as described in
                        section 4.2.

   The only destination options defined in this document are the Pad1
   and PadN options specified in section 4.2.

   Note that there are two possible ways to encode optional destination
   information in an IPv6 packet: either as an option in the Destination
   Options header, or as a separate extension header.  The Fragment
   header and the Authentication header are examples of the latter
   approach.  Which approach can be used depends on what action is
   desired of a destination node that does not understand the optional
   information:

      o  If the desired action is for the destination node to discard
         the packet and, only if the packet's Destination Address is not
         a multicast address, send an ICMP Unrecognized Type message to
         the packet's Source Address, then the information may be
         encoded either as a separate header or as an option in the



Deering & Hinden            Standards Track                    [Page 23]


RFC 2460                   IPv6 Specification              December 1998


         Destination Options header whose Option Type has the value 11
         in its highest-order two bits.  The choice may depend on such
         factors as which takes fewer octets, or which yields better
         alignment or more efficient parsing.

      o  If any other action is desired, the information must be encoded
         as an option in the Destination Options header whose Option
         Type has the value 00, 01, or 10 in its highest-order two bits,
         specifying the desired action (see section 4.2).

4.7 No Next Header

   The value 59 in the Next Header field of an IPv6 header or any
   extension header indicates that there is nothing following that
   header.  If the Payload Length field of the IPv6 header indicates the
   presence of octets past the end of a header whose Next Header field
   contains 59, those octets must be ignored, and passed on unchanged if
   the packet is forwarded.

5. Packet Size Issues

   IPv6 requires that every link in the internet have an MTU of 1280
   octets or greater.  On any link that cannot convey a 1280-octet
   packet in one piece, link-specific fragmentation and reassembly must
   be provided at a layer below IPv6.

   Links that have a configurable MTU (for example, PPP links [RFC-
   1661]) must be configured to have an MTU of at least 1280 octets; it
   is recommended that they be configured with an MTU of 1500 octets or
   greater, to accommodate possible encapsulations (i.e., tunneling)
   without incurring IPv6-layer fragmentation.

   From each link to which a node is directly attached, the node must be
   able to accept packets as large as that link's MTU.

   It is strongly recommended that IPv6 nodes implement Path MTU
   Discovery [RFC-1981], in order to discover and take advantage of path
   MTUs greater than 1280 octets.  However, a minimal IPv6
   implementation (e.g., in a boot ROM) may simply restrict itself to
   sending packets no larger than 1280 octets, and omit implementation
   of Path MTU Discovery.

   In order to send a packet larger than a path's MTU, a node may use
   the IPv6 Fragment header to fragment the packet at the source and
   have it reassembled at the destination(s).  However, the use of such
   fragmentation is discouraged in any application that is able to
   adjust its packets to fit the measured path MTU (i.e., down to 1280
   octets).



Deering & Hinden            Standards Track                    [Page 24]


RFC 2460                   IPv6 Specification              December 1998


   A node must be able to accept a fragmented packet that, after
   reassembly, is as large as 1500 octets.  A node is permitted to
   accept fragmented packets that reassemble to more than 1500 octets.
   An upper-layer protocol or application that depends on IPv6
   fragmentation to send packets larger than the MTU of a path should
   not send packets larger than 1500 octets unless it has assurance that
   the destination is capable of reassembling packets of that larger
   size.

   In response to an IPv6 packet that is sent to an IPv4 destination
   (i.e., a packet that undergoes translation from IPv6 to IPv4), the
   originating IPv6 node may receive an ICMP Packet Too Big message
   reporting a Next-Hop MTU less than 1280.  In that case, the IPv6 node
   is not required to reduce the size of subsequent packets to less than
   1280, but must include a Fragment header in those packets so that the
   IPv6-to-IPv4 translating router can obtain a suitable Identification
   value to use in resulting IPv4 fragments.  Note that this means the
   payload may have to be reduced to 1232 octets (1280 minus 40 for the
   IPv6 header and 8 for the Fragment header), and smaller still if
   additional extension headers are used.

6.  Flow Labels

   The 20-bit Flow Label field in the IPv6 header may be used by a
   source to label sequences of packets for which it requests special
   handling by the IPv6 routers, such as non-default quality of service
   or "real-time" service.  This aspect of IPv6 is, at the time of
   writing, still experimental and subject to change as the requirements
   for flow support in the Internet become clearer.  Hosts or routers
   that do not support the functions of the Flow Label field are
   required to set the field to zero when originating a packet, pass the
   field on unchanged when forwarding a packet, and ignore the field
   when receiving a packet.

   Appendix A describes the current intended semantics and usage of the
   Flow Label field.

7.  Traffic Classes

   The 8-bit Traffic Class field in the IPv6 header is available for use
   by originating nodes and/or forwarding routers to identify and
   distinguish between different classes or priorities of IPv6 packets.
   At the point in time at which this specification is being written,
   there are a number of experiments underway in the use of the IPv4
   Type of Service and/or Precedence bits to provide various forms of
   "differentiated service" for IP packets, other than through the use
   of explicit flow set-up.  The Traffic Class field in the IPv6 header
   is intended to allow similar functionality to be supported in IPv6.



Deering & Hinden            Standards Track                    [Page 25]


RFC 2460                   IPv6 Specification              December 1998


   It is hoped that those experiments will eventually lead to agreement
   on what sorts of traffic classifications are most useful for IP
   packets.  Detailed definitions of the syntax and semantics of all or
   some of the IPv6 Traffic Class bits, whether experimental or intended
   for eventual standardization, are to be provided in separate
   documents.

   The following general requirements apply to the Traffic Class field:

      o  The service interface to the IPv6 service within a node must
         provide a means for an upper-layer protocol to supply the value
         of the Traffic Class bits in packets originated by that upper-
         layer protocol.  The default value must be zero for all 8 bits.

      o  Nodes that support a specific (experimental or eventual
         standard) use of some or all of the Traffic Class bits are
         permitted to change the value of those bits in packets that
         they originate, forward, or receive, as required for that
         specific use.  Nodes should ignore and leave unchanged any bits
         of the Traffic Class field for which they do not support a
         specific use.

      o  An upper-layer protocol must not assume that the value of the
         Traffic Class bits in a received packet are the same as the
         value sent by the packet's source.


























Deering & Hinden            Standards Track                    [Page 26]


RFC 2460                   IPv6 Specification              December 1998


8. Upper-Layer Protocol Issues

8.1 Upper-Layer Checksums

   Any transport or other upper-layer protocol that includes the
   addresses from the IP header in its checksum computation must be
   modified for use over IPv6, to include the 128-bit IPv6 addresses
   instead of 32-bit IPv4 addresses.  In particular, the following
   illustration shows the TCP and UDP "pseudo-header" for IPv6:

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   |                                                               |
   +                         Source Address                        +
   |                                                               |
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   |                                                               |
   +                      Destination Address                      +
   |                                                               |
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                   Upper-Layer Packet Length                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      zero                     |  Next Header  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      o  If the IPv6 packet contains a Routing header, the Destination
         Address used in the pseudo-header is that of the final
         destination.  At the originating node, that address will be in
         the last element of the Routing header; at the recipient(s),
         that address will be in the Destination Address field of the
         IPv6 header.

      o  The Next Header value in the pseudo-header identifies the
         upper-layer protocol (e.g., 6 for TCP, or 17 for UDP).  It will
         differ from the Next Header value in the IPv6 header if there
         are extension headers between the IPv6 header and the upper-
         layer header.

      o  The Upper-Layer Packet Length in the pseudo-header is the
         length of the upper-layer header and data (e.g., TCP header
         plus TCP data).  Some upper-layer protocols carry their own



Deering & Hinden            Standards Track                    [Page 27]


RFC 2460                   IPv6 Specification              December 1998


         length information (e.g., the Length field in the UDP header);
         for such protocols, that is the length used in the pseudo-
         header.  Other protocols (such as TCP) do not carry their own
         length information, in which case the length used in the
         pseudo-header is the Payload Length from the IPv6 header, minus
         the length of any extension headers present between the IPv6
         header and the upper-layer header.

      o  Unlike IPv4, when UDP packets are originated by an IPv6 node,
         the UDP checksum is not optional.  That is, whenever
         originating a UDP packet, an IPv6 node must compute a UDP
         checksum over the packet and the pseudo-header, and, if that
         computation yields a result of zero, it must be changed to hex
         FFFF for placement in the UDP header.  IPv6 receivers must
         discard UDP packets containing a zero checksum, and should log
         the error.

   The IPv6 version of ICMP [ICMPv6] includes the above pseudo-header in
   its checksum computation; this is a change from the IPv4 version of
   ICMP, which does not include a pseudo-header in its checksum.  The
   reason for the change is to protect ICMP from misdelivery or
   corruption of those fields of the IPv6 header on which it depends,
   which, unlike IPv4, are not covered by an internet-layer checksum.
   The Next Header field in the pseudo-header for ICMP contains the
   value 58, which identifies the IPv6 version of ICMP.

8.2 Maximum Packet Lifetime

   Unlike IPv4, IPv6 nodes are not required to enforce maximum packet
   lifetime.  That is the reason the IPv4 "Time to Live" field was
   renamed "Hop Limit" in IPv6.  In practice, very few, if any, IPv4
   implementations conform to the requirement that they limit packet
   lifetime, so this is not a change in practice.  Any upper-layer
   protocol that relies on the internet layer (whether IPv4 or IPv6) to
   limit packet lifetime ought to be upgraded to provide its own
   mechanisms for detecting and discarding obsolete packets.

8.3 Maximum Upper-Layer Payload Size

   When computing the maximum payload size available for upper-layer
   data, an upper-layer protocol must take into account the larger size
   of the IPv6 header relative to the IPv4 header.  For example, in
   IPv4, TCP's MSS option is computed as the maximum packet size (a
   default value or a value learned through Path MTU Discovery) minus 40
   octets (20 octets for the minimum-length IPv4 header and 20 octets
   for the minimum-length TCP header).  When using TCP over IPv6, the
   MSS must be computed as the maximum packet size minus 60 octets,




Deering & Hinden            Standards Track                    [Page 28]


RFC 2460                   IPv6 Specification              December 1998


   because the minimum-length IPv6 header (i.e., an IPv6 header with no
   extension headers) is 20 octets longer than a minimum-length IPv4
   header.

8.4 Responding to Packets Carrying Routing Headers

   When an upper-layer protocol sends one or more packets in response to
   a received packet that included a Routing header, the response
   packet(s) must not include a Routing header that was automatically
   derived by "reversing" the received Routing header UNLESS the
   integrity and authenticity of the received Source Address and Routing
   header have been verified (e.g., via the use of an Authentication
   header in the received packet).  In other words, only the following
   kinds of packets are permitted in response to a received packet
   bearing a Routing header:

      o  Response packets that do not carry Routing headers.

      o  Response packets that carry Routing headers that were NOT
         derived by reversing the Routing header of the received packet
         (for example, a Routing header supplied by local
         configuration).

      o  Response packets that carry Routing headers that were derived
         by reversing the Routing header of the received packet IF AND
         ONLY IF the integrity and authenticity of the Source Address
         and Routing header from the received packet have been verified
         by the responder.























Deering & Hinden            Standards Track                    [Page 29]


RFC 2460                   IPv6 Specification              December 1998


Appendix A. Semantics and Usage of the Flow Label Field

   A flow is a sequence of packets sent from a particular source to a
   particular (unicast or multicast) destination for which the source
   desires special handling by the intervening routers.  The nature of
   that special handling might be conveyed to the routers by a control
   protocol, such as a resource reservation protocol, or by information
   within the flow's packets themselves, e.g., in a hop-by-hop option.
   The details of such control protocols or options are beyond the scope
   of this document.

   There may be multiple active flows from a source to a destination, as
   well as traffic that is not associated with any flow.  A flow is
   uniquely identified by the combination of a source address and a
   non-zero flow label.  Packets that do not belong to a flow carry a
   flow label of zero.

   A flow label is assigned to a flow by the flow's source node.  New
   flow labels must be chosen (pseudo-)randomly and uniformly from the
   range 1 to FFFFF hex.  The purpose of the random allocation is to
   make any set of bits within the Flow Label field suitable for use as
   a hash key by routers, for looking up the state associated with the
   flow.

   All packets belonging to the same flow must be sent with the same
   source address, destination address, and flow label.  If any of those
   packets includes a Hop-by-Hop Options header, then they all must be
   originated with the same Hop-by-Hop Options header contents
   (excluding the Next Header field of the Hop-by-Hop Options header).
   If any of those packets includes a Routing header, then they all must
   be originated with the same contents in all extension headers up to
   and including the Routing header (excluding the Next Header field in
   the Routing header).  The routers or destinations are permitted, but
   not required, to verify that these conditions are satisfied.  If a
   violation is detected, it should be reported to the source by an ICMP
   Parameter Problem message, Code 0, pointing to the high-order octet
   of the Flow Label field (i.e., offset 1 within the IPv6 packet).

   The maximum lifetime of any flow-handling state established along a
   flow's path must be specified as part of the description of the
   state-establishment mechanism, e.g., the resource reservation
   protocol or the flow-setup hop-by-hop option.  A source must not re-
   use a flow label for a new flow within the maximum lifetime of any
   flow-handling state that might have been established for the prior
   use of that flow label.






Deering & Hinden            Standards Track                    [Page 30]


RFC 2460                   IPv6 Specification              December 1998


   When a node stops and restarts (e.g., as a result of a "crash"), it
   must be careful not to use a flow label that it might have used for
   an earlier flow whose lifetime may not have expired yet.  This may be
   accomplished by recording flow label usage on stable storage so that
   it can be remembered across crashes, or by refraining from using any
   flow labels until the maximum lifetime of any possible previously
   established flows has expired.  If the minimum time for rebooting the
   node is known, that time can be deducted from the necessary waiting
   period before starting to allocate flow labels.

   There is no requirement that all, or even most, packets belong to
   flows, i.e., carry non-zero flow labels.  This observation is placed
   here to remind protocol designers and implementors not to assume
   otherwise.  For example, it would be unwise to design a router whose
   performance would be adequate only if most packets belonged to flows,
   or to design a header compression scheme that only worked on packets
   that belonged to flows.


































Deering & Hinden            Standards Track                    [Page 31]


RFC 2460                   IPv6 Specification              December 1998


Appendix B. Formatting Guidelines for Options

   This appendix gives some advice on how to lay out the fields when
   designing new options to be used in the Hop-by-Hop Options header or
   the Destination Options header, as described in section 4.2.  These
   guidelines are based on the following assumptions:

      o  One desirable feature is that any multi-octet fields within the
         Option Data area of an option be aligned on their natural
         boundaries, i.e., fields of width n octets should be placed at
         an integer multiple of n octets from the start of the Hop-by-
         Hop or Destination Options header, for n = 1, 2, 4, or 8.

      o  Another desirable feature is that the Hop-by-Hop or Destination
         Options header take up as little space as possible, subject to
         the requirement that the header be an integer multiple of 8
         octets long.

      o  It may be assumed that, when either of the option-bearing
         headers are present, they carry a very small number of options,
         usually only one.

   These assumptions suggest the following approach to laying out the
   fields of an option: order the fields from smallest to largest, with
   no interior padding, then derive the alignment requirement for the
   entire option based on the alignment requirement of the largest field
   (up to a maximum alignment of 8 octets).  This approach is
   illustrated in the following examples:

   Example 1

   If an option X required two data fields, one of length 8 octets and
   one of length 4 octets, it would be laid out as follows:


                                   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
                                   | Option Type=X |Opt Data Len=12|
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         4-octet field                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                         8-octet field                         +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+







Deering & Hinden            Standards Track                    [Page 32]


RFC 2460                   IPv6 Specification              December 1998


   Its alignment requirement is 8n+2, to ensure that the 8-octet field
   starts at a multiple-of-8 offset from the start of the enclosing
   header.  A complete Hop-by-Hop or Destination Options header
   containing this one option would look as follows:

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  Next Header  | Hdr Ext Len=1 | Option Type=X |Opt Data Len=12|
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         4-octet field                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                         8-octet field                         +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Example 2

   If an option Y required three data fields, one of length 4 octets,
   one of length 2 octets, and one of length 1 octet, it would be laid
   out as follows:

                                                   +-+-+-+-+-+-+-+-+
                                                   | Option Type=Y |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |Opt Data Len=7 | 1-octet field |         2-octet field         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         4-octet field                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Its alignment requirement is 4n+3, to ensure that the 4-octet field
   starts at a multiple-of-4 offset from the start of the enclosing
   header.  A complete Hop-by-Hop or Destination Options header
   containing this one option would look as follows:

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  Next Header  | Hdr Ext Len=1 | Pad1 Option=0 | Option Type=Y |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |Opt Data Len=7 | 1-octet field |         2-octet field         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         4-octet field                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | PadN Option=1 |Opt Data Len=2 |       0       |       0       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+








Deering & Hinden            Standards Track                    [Page 33]


RFC 2460                   IPv6 Specification              December 1998


   Example 3

   A Hop-by-Hop or Destination Options header containing both options X
   and Y from Examples 1 and 2 would have one of the two following
   formats, depending on which option appeared first:

   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  Next Header  | Hdr Ext Len=3 | Option Type=X |Opt Data Len=12|
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         4-octet field                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                         8-octet field                         +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | PadN Option=1 |Opt Data Len=1 |       0       | Option Type=Y |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |Opt Data Len=7 | 1-octet field |         2-octet field         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         4-octet field                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | PadN Option=1 |Opt Data Len=2 |       0       |       0       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |  Next Header  | Hdr Ext Len=3 | Pad1 Option=0 | Option Type=Y |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |Opt Data Len=7 | 1-octet field |         2-octet field         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         4-octet field                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | PadN Option=1 |Opt Data Len=4 |       0       |       0       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       0       |       0       | Option Type=X |Opt Data Len=12|
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         4-octet field                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                         8-octet field                         +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+









Deering & Hinden            Standards Track                    [Page 34]


RFC 2460                   IPv6 Specification              December 1998


Security Considerations

   The security features of IPv6 are described in the Security
   Architecture for the Internet Protocol [RFC-2401].

Acknowledgments

   The authors gratefully acknowledge the many helpful suggestions of
   the members of the IPng working group, the End-to-End Protocols
   research group, and the Internet Community At Large.

Authors' Addresses

   Stephen E. Deering
   Cisco Systems, Inc.
   170 West Tasman Drive
   San Jose, CA 95134-1706
   USA

   Phone: +1 408 527 8213
   Fax:   +1 408 527 8254
   EMail: deering@cisco.com


   Robert M. Hinden
   Nokia
   232 Java Drive
   Sunnyvale, CA 94089
   USA

   Phone: +1 408 990-2004
   Fax:   +1 408 743-5677
   EMail: hinden@iprg.nokia.com

References

   [RFC-2401]   Kent, S. and R. Atkinson, "Security Architecture for the
                Internet Protocol", RFC 2401, November 1998.

   [RFC-2402]   Kent, S. and R. Atkinson, "IP Authentication Header",
                RFC 2402, November 1998.

   [RFC-2406]   Kent, S. and R. Atkinson, "IP Encapsulating Security
                Protocol (ESP)", RFC 2406, November 1998.

   [ICMPv6]     Conta, A. and S. Deering, "ICMP for the Internet
                Protocol Version 6 (IPv6)", RFC 2463, December 1998.




Deering & Hinden            Standards Track                    [Page 35]


RFC 2460                   IPv6 Specification              December 1998


   [ADDRARCH]   Hinden, R. and S. Deering, "IP Version 6 Addressing
                Architecture", RFC 2373, July 1998.

   [RFC-1981]   McCann, J., Mogul, J. and S. Deering, "Path MTU
                Discovery for IP version 6", RFC 1981, August 1996.

   [RFC-791]    Postel, J., "Internet Protocol", STD 5, RFC 791,
                September 1981.

   [RFC-1700]   Reynolds, J. and J. Postel, "Assigned Numbers", STD 2,
                RFC 1700, October 1994.  See also:
                http://www.iana.org/numbers.html

   [RFC-1661]   Simpson, W., "The Point-to-Point Protocol (PPP)", STD
                51, RFC 1661, July 1994.

CHANGES SINCE RFC-1883

   This memo has the following changes from RFC-1883.  Numbers identify
   the Internet-Draft version in which the change was made.

    02) Removed all references to jumbograms and the Jumbo Payload
        option (moved to a separate document).

    02) Moved most of Flow Label description from section 6 to (new)
        Appendix A.

    02) In Flow Label description, now in Appendix A, corrected maximum
        Flow Label value from FFFFFF to FFFFF (i.e., one less "F") due
        to reduction of size of Flow Label field from 24 bits to 20
        bits.

    02) Renumbered (relettered?) the previous Appendix A to be Appendix
        B.

    02) Changed the wording of the Security Considerations section to
        avoid dependency loop between this spec and the IPsec specs.

    02) Updated R. Hinden's email address and company affiliation.


        --------------------------------------------------------

    01) In section 3, changed field name "Class" to "Traffic Class" and
        increased its size from 4 to 8 bits.  Decreased size of Flow
        Label field from 24 to 20 bits to compensate for increase in
        Traffic Class field.




Deering & Hinden            Standards Track                    [Page 36]


RFC 2460                   IPv6 Specification              December 1998


    01) In section 4.1, restored the order of the Authentication Header
        and the ESP header, which were mistakenly swapped in the 00
        version of this memo.

    01) In section 4.4, deleted the Strict/Loose Bit Map field and the
        strict routing functionality from the Type 0 Routing header, and
        removed the restriction on number of addresses that may be
        carried in the Type 0 Routing header (was limited to 23
        addresses, because of the size of the strict/loose bit map).

    01) In section 5, changed the minimum IPv6 MTU from 576 to 1280
        octets, and added a recommendation that links with configurable
        MTU (e.g., PPP links) be configured to have an MTU of at least
        1500 octets.

    01) In section 5, deleted the requirement that a node must not send
        fragmented packets that reassemble to more than 1500 octets
        without knowledge of the destination reassembly buffer size, and
        replaced it with a recommendation that upper-layer protocols or
        applications should not do that.

    01) Replaced reference to the IPv4 Path MTU Discovery spec (RFC-
        1191) with reference to the IPv6 Path MTU Discovery spec (RFC-
        1981), and deleted the Notes at the end of section 5 regarding
        Path MTU Discovery, since those details are now covered by RFC-
        1981.

    01) In section 6, deleted specification of "opportunistic" flow
        set-up, and removed all references to the 6-second maximum
        lifetime for opportunistically established flow state.

    01) In section 7, deleted the provisional description of the
        internal structure and semantics of the Traffic Class field, and
        specified that such descriptions be provided in separate
        documents.

        --------------------------------------------------------

    00) In section 4, corrected the Code value to indicate "unrecognized
        Next Header type encountered" in an ICMP Parameter Problem
        message (changed from 2 to 1).

    00) In the description of the Payload Length field in section 3, and
        of the Jumbo Payload Length field in section 4.3, made it
        clearer that extension headers are included in the payload
        length count.





Deering & Hinden            Standards Track                    [Page 37]


RFC 2460                   IPv6 Specification              December 1998


    00) In section 4.1, swapped the order of the Authentication header
        and the ESP header.  (NOTE: this was a mistake, and the change
        was undone in version 01.)

    00) In section 4.2, made it clearer that options are identified by
        the full 8-bit Option Type, not by the low-order 5 bits of an
        Option Type.  Also specified that the same Option Type numbering
        space is used for both Hop-by-Hop Options and Destination
        Options headers.

    00) In section 4.4, added a sentence requiring that nodes processing
        a Routing header must send an ICMP Packet Too Big message in
        response to a packet that is too big to fit in the next hop link
        (rather than, say, performing fragmentation).

    00) Changed the name of the IPv6 Priority field to "Class", and
        replaced the previous description of Priority in section 7 with
        a description of the Class field.  Also, excluded this field
        from the set of fields that must remain the same for all packets
        in the same flow, as specified in section 6.

    00) In the pseudo-header in section 8.1, changed the name of the
        "Payload Length" field to "Upper-Layer Packet Length".  Also
        clarified that, in the case of protocols that carry their own
        length info (like non-jumbogram UDP), it is the upper-layer-
        derived length, not the IP-layer-derived length, that is used in
        the pseudo-header.

    00) Added section 8.4, specifying that upper-layer protocols, when
        responding to a received packet that carried a Routing header,
        must not include the reverse of the Routing header in the
        response packet(s) unless the received Routing header was
        authenticated.

    00) Fixed some typos and grammatical errors.

    00) Authors' contact info updated.

        --------------------------------------------------------












Deering & Hinden            Standards Track                    [Page 38]


RFC 2460                   IPv6 Specification              December 1998


Full Copyright Statement

   Copyright (C) The Internet Society (1998).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
























Deering & Hinden            Standards Track                    [Page 39]