[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]

INFORMATIONAL
Network Working Group                                           J. Welch
Request for Comments: 4445                        IneoQuest Technologies
Category: Informational                                         J. Clark
                                                           Cisco Systems
                                                              April 2006


                 A Proposed Media Delivery Index (MDI)

Status of This Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2006).

IESG Note

   This RFC is not a candidate for any level of Internet Standard.
   There are IETF standards which are highly applicable to the space
   defined by this document as its applicability, in particular, RFCs
   3393 and 3611, and there is ongoing IETF work in these areas as well.
   The IETF also notes that the decision to publish this RFC is not
   based on IETF review for such things as security, congestion control,
   MIB fitness, or inappropriate interaction with deployed protocols.
   The RFC Editor has chosen to publish this document at its discretion.
   Readers of this document should exercise caution in evaluating its
   value for implementation and deployment.  See RFC 3932 for more
   information.

Abstract

   This memo defines a Media Delivery Index (MDI) measurement that can
   be used as a diagnostic tool or a quality indicator for monitoring a
   network intended to deliver applications such as streaming media,
   MPEG video, Voice over IP, or other information sensitive to arrival
   time and packet loss.  It provides an indication of traffic jitter, a
   measure of deviation from nominal flow rates, and a data loss
   at-a-glance measure for a particular flow.  For instance, the MDI may
   be used as a reference in characterizing and comparing networks
   carrying UDP streaming media.

   The MDI measurement defined in this memo is intended for Information
   only.




Welch & Clark                Informational                      [Page 1]


RFC 4445         A Proposed Media Delivery Index (MDI)        April 2006


1.  Introduction

   There has been considerable progress over the last several years in
   the development of methods to provide for Quality of Service (QoS)
   over packet-switched networks to improve the delivery of streaming
   media and other time-sensitive and packet-loss-sensitive applications
   such as [i1], [i5], [i6], [i7].  QoS is required for many practical
   networks involving applications such as video transport to assure the
   availability of network bandwidth by providing upper limits on the
   number of flows admitted to a network, as well as to bound the packet
   jitter introduced by the network.  These bounds are required to
   dimension a receiver`s buffer to display the video properly in real
   time without buffer overflow or underflow.

   Now that large-scale implementations of such networks based on RSVP
   and Diffserv are undergoing trials [i3] and being specified by major
   service providers for the transport of streaming media such as MPEG
   video [i4], there is a need to diagnose issues easily and to monitor
   the real-time effectiveness of networks employing these QoS methods
   or to assess whether they are required.  Furthermore, due to the
   significant installed base of legacy networks without QoS methods, a
   delivery system`s transitional solution may be composed of networks
   with and without these methods, thus increasing the difficulty in
   characterizing the dynamic behavior of these networks.

   The purpose of this memo is to describe a set of measurements that
   can be used to derive a Media Delivery Index (MDI) that indicates the
   instantaneous and longer-term behavior of networks carrying streaming
   media such as MPEG video.

   While this memo addresses monitoring MPEG Transport Stream (TS)
   packets [i8] over UDP, the general approach is expected to be
   applicable to other streaming media and protocols.  The approach is
   applicable to both constant and variable bit rate streams though the
   variable bit rate case may be somewhat more difficult to calculate.
   This document focuses on the constant bit rate case as the example to
   describe the measurement, but as long as the dynamic bit rate of the
   encoded stream can be determined (the "drain rate" as described below
   in Section 3), then the MDI provides the measurement of network-
   induced cumulative jitter.  Suggestions and direction for calculation
   of MDI for a variable bit rate encoded stream may be the subject of a
   future document.

   Network packet delivery time variation and various statistics to
   characterize the same are described in a generic approach in [i10].
   The approach is capable of being parameterized for various purposes
   with the intent of defining a flexible, customizable definition that
   can be applied to a wide range of applications and further



Welch & Clark                Informational                      [Page 2]


RFC 4445         A Proposed Media Delivery Index (MDI)        April 2006


   experimentation.  Other approaches to characterizing jitter behavior
   are also captured such as in [i12].  A wide-ranging report format
   [i11] has been described to convey information including jitter for
   use with the RTP Control Protocol (RTCP) [i12].  The MDI is instead
   intended to specifically address the need for a scalable,
   economical-to-compute metric that characterizes network impairments
   that may be imposed on streaming media, independent of control plane
   or measurement transport protocol or stream encapsulation protocol.
   It is a targeted metric for use in production networks carrying large
   numbers of streams for the purpose of monitoring the network quality
   of the flows or for other applications intended to analyze large
   numbers of streams susceptible to IP network device impairments.  An
   example application is the burgeoning deployments of Internet
   Protocol Television (IPTV) by cable and telecommunication service
   providers.  As described below, MDI provides for a readily scalable
   per-stream measure focused on loss and the cumulative effects of
   jitter.

2.  Media Delivery Index Overview

   The MDI provides a relative indicator of needed buffer depths at the
   consumer node due to packet jitter as well as an indication of lost
   packets.  By probing a streaming media service network at various
   nodes and under varying load conditions, it is possible to quickly
   identify devices or locales that introduce significant jitter or
   packet loss to the packet stream.  By monitoring a network
   continuously, deviations from nominal jitter or loss behavior can be
   used to indicate an impending or ongoing fault condition such as
   excessive load.  It is believed that the MDI provides the necessary
   information to detect all network-induced impairments for streaming
   video or voice-over-IP applications.  Other parameters may be
   required to troubleshoot and correct the impairments.

   The MDI is updated at the termination of selected time intervals
   spanning multiple packets that contain the streaming media (such as
   transport stream packets in the MPEG-2 case).  The Maximums and
   Minimums of the MDI component values are captured over a measurement
   time.  The measurement time may range from just long enough to
   capture an anticipated network anomaly during a troubleshooting
   exercise to indefinitely long for a long-term monitoring or logging
   application.  The Maximums and Minimums may be obtained by sampling
   the measurement with adequate frequency.









Welch & Clark                Informational                      [Page 3]


RFC 4445         A Proposed Media Delivery Index (MDI)        April 2006


3.  Media Delivery Index Components

   The MDI consists of two components:  the Delay Factor (DF) and the
   Media Loss Rate (MLR).

3.1.  Delay Factor

   The Delay Factor is the maximum difference, observed at the end of
   each media stream packet, between the arrival of media data and the
   drain of media data.  This assumes the drain rate is the nominal
   constant traffic rate for constant bit rate streams or the piece-wise
   computed traffic rate of variable rate media stream packet data.  The
   "drain rate" here refers to the payload media rate; e.g., for a
   typical 3.75 Mb/s MPEG video Transport Stream (TS), the drain rate is
   3.75 Mb/s -- the rate at which the payload is consumed (displayed) at
   a decoding node.  If, at the sample time, the number of bytes
   received equals the number transmitted, the instantaneous flow rate
   balance will be zero; however, the minimum DF will be a line packet's
   worth of media data, as that is the minimum amount of data that must
   be buffered.

   The DF is the maximum observed value of the flow rate imbalance over
   a calculation interval.  This buffered media data in bytes is
   expressed in terms of how long, in milliseconds, it would take to
   drain (or fill) this data at the nominal traffic rate to obtain the
   DF.  Display of DF with a resolution of tenths of milliseconds is
   recommended to provide adequate indication of stream variations for
   monitoring and diagnostic applications for typical stream rates from
   1 to 40 Mb/s.  The DF value must be updated and displayed at the end
   of a selected time interval.  The selected time interval is chosen to
   be long enough to sample a number of TS packets and will, therefore,
   vary based on the nominal traffic rate.  For typical stream rates of
   1 Mb/s and up, an interval of 1 second provides a long enough sample
   time and should be included for all implementations.  The Delay
   Factor indicates how long a data stream must be buffered (i.e.,
   delayed) at its nominal bit rate to prevent packet loss.  This time
   may also be seen as a measure of the network latency that must be
   induced from buffering, which is required to accommodate stream
   jitter and prevent loss.  The DF`s max and min over the measurement
   period (multiple intervals) may also be displayed to show the worst
   case arrival time deviation, or jitter, relative to the nominal
   traffic rate in a measurement period.  It provides a dynamic flow
   rate balance indication with its max and min showing the worst
   excursions from balance.

   The Delay Factor gives a hint of the minimum size of the buffer
   required at the next downstream node.  As a stream progresses, the
   variation of the Delay Factor indicates packet bunching or packet



Welch & Clark                Informational                      [Page 4]


RFC 4445         A Proposed Media Delivery Index (MDI)        April 2006


   gaps (jitter).  Greater DF values also indicate that more network
   latency is necessary to deliver a stream due to the need to pre-fill
   a receive buffer before beginning the drain to guarantee no
   underflow.  The DF comprises a fixed part based on packet size and a
   variable part based on the buffer utilization of the various network
   component switch elements that comprise the switched network
   infrastructure [i2].

   To further detail the calculation of DF, consider a virtual buffer VB
   used to buffer received packets of a stream.  When a packet P(i)
   arrives during a calculation interval, compute two VB values,
   VB(i,pre) and VB(i,post), defined as:

   VB(i,pre) = sum (Sj) - MR * Ti; where j=1..i-1
   VB(i,post) = VB(i,pre) + Si

   where Sj is the media payload size of the jth packet, Ti is the
   relative time at which packet i arrives in the interval, and MR is
   the nominal media rate.

   VB(i,pre) is the Virtual Buffer size just before the arrival of P(i).
   VB(i,post) is the Virtual Buffer size just after the arrival of P(i).

   The initial condition of VB(0) = 0 is used at the beginning of each
   measurement interval.  A measurement interval is defined from just
   after the time of arrival of the last packet during a nominal period
   (typically 1 second) as mentioned above to the time just after the
   arrival of the last packet of the next nominal period.

   During a measurement interval, if k packets are received, then there
   are 2*k+1 VB values used in deriving VB(max) and VB(min).  After
   determining VB(max) and VB(min) from the 2k+1 VB samples, DF for the
   measurement interval is computed and displayed as:

   DF = [VB(max) - VB(min)]/ MR

   As noted above, a measurement interval of 1 second is typically used.
   If no packets are received during an interval, the last DF calculated
   during an interval in which packets did arrive is displayed.  The
   time of arrival of the last previous packet is always retained for
   use in calculating VB when the next packet arrives (even if the time
   of the last received packet spans measurement intervals).  For the
   first received measurement interval of a measurement period, no DF is
   calculated; however, packet arrival times are recorded for use in
   calculating VB during the following interval.






Welch & Clark                Informational                      [Page 5]


RFC 4445         A Proposed Media Delivery Index (MDI)        April 2006


3.2.  Media Loss Rate

   The Media Loss Rate is the count of lost or out-of-order flow packets
   over a selected time interval, where the flow packets are packets
   carrying streaming application information.  There may be zero or
   more streaming packets in a single IP packet.  For example, it is
   common to carry seven 188 Byte MPEG Transport Stream packets in an IP
   packet.  In such a case, a single IP packet loss would result in 7
   lost packets counted (if those 7 lost packets did not include null
   packets).  Including out-of-order packets is important, as many
   stream consumer-type devices do not attempt to reorder packets that
   are received out of order.

3.3.  Media Delivery Index

   Combining the Delay Factor and Media Loss Rate quantities for
   presentation results in the following MDI:

                                  DF:MLR
    Where:
                          DF is the Delay Factor
                        MLR is the Media Loss Rate

   At a receiving node, knowing its nominal drain bit rate, the DF`s max
   indicates the size of buffer required to accommodate packet jitter.
   Or, in terms of Leaky Bucket [i9] parameters, DF indicates bucket
   size b, expressed in time to transmit bucket traffic b, at the given
   nominal traffic rate, r.

3.4.  MDI Application Examples

   If a known, well-characterized receive node is separated from the
   data source by unknown or less well-characterized nodes such as
   intermediate switch nodes, the MDI measured at intermediate data
   links provides a relative indication of the behavior of upstream
   traffic flows.  DF difference indications between one node and
   another in a data stream for a given constant interval of calculation
   can indicate local areas of traffic congestion or possibly
   misconfigured QoS flow specification(s) leading to greater filling of
   measurement point local device buffers, resultant flow rate
   deviations, and possible data loss.










Welch & Clark                Informational                      [Page 6]


RFC 4445         A Proposed Media Delivery Index (MDI)        April 2006


   For a given MDI, if DF is high and/or the DF Max-Min captured over a
   significant measurement period of multiple intervals is high, jitter
   has been detected but the longer-term, average flow rate may be
   nominal.  This could be the result of a transient flow upset due to a
   coincident traffic stream unrelated to the flow of interest causing
   packet bunching.  A high DF may cause downstream buffer overflow or
   underflow or unacceptable latency even in the absence of lost data.

   Due to transient network failures or DF excursions, packets may be
   lost within the network.  The MLR component of the MDI shows this
   condition.

   Through automated or manual flow detection and identification and
   subsequent MDI calculations for real-time statistics on a flow, the
   DF can indicate the dynamic deterioration or increasing burstiness of
   a flow, which can be used to anticipate a developing network
   operation problem such as transient oversubscription.  Such
   statistics can be obtained for flows within network switches using
   available switch cpu resources due to the minimal computational
   requirements needed for small numbers of flows.  Statistics for all
   flows present on, say, a gigabit Ethernet network, will likely
   require dedicated hardware facilities, though these can be modest, as
   buffer requirements and the required calculations per flow are
   minimal.  By equipping network switches with MDI measurements, flow
   impairment issues can quickly be identified, localized, and
   corrected.  Until switches are so equipped with appropriate hardware
   resources, dedicated hardware tools can provide supplemental switch
   statistics by gaining access to switch flows via mirror ports, link
   taps, or the like as a transition strategy.

   The MDI figure can also be used to characterize a flow decoder's
   acceptable performance.  For example, an MPEG decoder could be
   characterized as tolerating a flow with a given maximum DF and MLR
   for acceptable display performance (acceptable on-screen artifacts).
   Network conditions such as Interior Gateway Protocol (IGP)
   reconvergence time then might also be included in the flow tolerance
   DF resulting in a higher-quality user experience.

4.  Summary

   The MDI combines the Delay Factor, which indicates potential for
   impending data loss, and Media Loss Rate as the indicator of lost
   data.  By monitoring the DF and MLR and their min and max excursions
   over a measurement period and at multiple strategic locations in a
   network, traffic congestion or device impairments may be detected and
   isolated for a network carrying streaming media content.





Welch & Clark                Informational                      [Page 7]


RFC 4445         A Proposed Media Delivery Index (MDI)        April 2006


5.  Security Considerations

   The measurements identified in this document do not directly affect
   the security of a network or user.  Actions taken in response to
   these measurements that may affect the available bandwidth of the
   network or the availability of a service is out of scope for this
   document.

   Performing the measurements described in this document only requires
   examination of payload header information (such as MPEG transport
   stream headers or RTP headers) to determine nominal stream bit rate
   and sequence number information.  Content may be encrypted without
   affecting these measurements.  Therefore, content privacy is not
   expected to be a concern.

6.  Informative References

   [i1]  Braden, R., Zhang, L., Berson, S., Herzog, S., and S. Jamin,
         "Resource ReSerVation Protocol (RSVP) -- Version 1 Functional
         Specification", RFC 2205, September 1997.

   [i2]  Partridge, C., "A Proposed Flow Specification", RFC 1363,
         September 1992.

   [i3]  R. Fellman, `Hurdles to Overcome for Broadcast Quality Video
         Delivery over IP` VidTranS 2002.

   [i4]  CableLabs `PacketCable Dynamic Quality-of-Service
         Specification`, PKT-SP-DQOS-I06-030415, 2003.

   [i5]  Shenker, S., Partridge, C., and R. Guerin, "Specification of
         Guaranteed Quality of Service", RFC 2212, September 1997.

   [i6]  Wroclawski, J., "Specification of the Controlled-Load Network
         Element Service", RFC 2211, September 1997.

   [i7]  Braden, R., Clark, D., and S. Shenker, "Integrated Services in
         the Internet Architecture: an Overview", RFC 1633, June 1994.

   [i8]  ISO/IEC 13818-1 (MPEG-2 Systems)

   [i9]  V. Raisanen, "Implementing Service Quality in IP Networks",
         John Wiley & Sons Ltd., 2003.

   [i10] Demichelis, C. and P. Chimento, "IP Packet Delay Variation
         Metric for IP Performance Metrics (IPPM)", RFC 3393, November
         2002.




Welch & Clark                Informational                      [Page 8]


RFC 4445         A Proposed Media Delivery Index (MDI)        April 2006


   [i11] Friedman, T., Caceres, R., and A. Clark, "RTP Control Protocol
         Extended Reports (RTCP XR)", RFC 3611, November 2003.

   [i12] Schulzrinne, H.,  Casner, S., Frederick, R., and V. Jacobson,
         "RTP: A Transport Protocol for Real-Time Applications", STD 64,
         RFC 3550, July 2003.

7.  Acknowledgements

   The authors gratefully acknowledge the contributions of Marc Todd and
   Jesse Beeson of IneoQuest Technologies, Inc., Bill Trubey and John
   Carlucci of Time Warner Cable, Nishith Sinha of Cox Communications,
   Ken Chiquoine of SeaChange International, Phil Proulx of Bell Canada,
   Dr Paul Stallard of TANDBERG Television, Gary Hughes of Broadbus
   Technologies, Brad Medford of SBC Laboratories, John Roy of Adelphia
   Communications, Cliff Mercer, PhD of Kasenna, Mathew Ho of Rogers
   Cable, and Irl Duling of Optinel Systems for reviewing and evaluating
   early versions of this document and implementations for MDI.

Authors' Addresses

   James Welch
   IneoQuest Technologies, Inc
   170 Forbes Blvd
   Mansfield, Massachusetts 02048

   Phone: 508 618 0312
   EMail: Jim.Welch@ineoquest.com


   James Clark
   Cisco Systems, Inc
   500 Northridge Road
   Suite 800
   Atlanta, Georgia 30350

   Phone: 678 352 2726
   EMail: jiclark@cisco.com













Welch & Clark                Informational                      [Page 9]


RFC 4445         A Proposed Media Delivery Index (MDI)        April 2006


Full Copyright Statement

   Copyright (C) The Internet Society (2006).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78 and at www.rfc-editor.org/copyright.html, and
   except as set forth therein, the authors retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is provided by the IETF
   Administrative Support Activity (IASA).







Welch & Clark                Informational                     [Page 10]