[RFC Home] [TEXT|PDF|HTML] [Tracker] [IPR] [Info page]

INFORMATIONAL
Network Working Group                                       L-E. Jonsson
Request for Comments: 3759                                      Ericsson
Updates: 3095                                                 April 2004
Category: Informational


                   RObust Header Compression (ROHC):
                Terminology and Channel Mapping Examples

Status of this Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2004).  All Rights Reserved.

Abstract

   This document aims to clarify terms and concepts presented in RFC
   3095.  RFC 3095 defines a Proposed Standard framework with profiles
   for RObust Header Compression (ROHC).  The standard introduces
   various concepts which might be difficult to understand and
   especially to relate correctly to the surrounding environments where
   header compression may be used.  This document aims at clarifying
   these aspects of ROHC, discussing terms such as ROHC instances, ROHC
   channels, ROHC feedback, and ROHC contexts, and how these terms
   relate to other terms, like network elements and IP interfaces,
   commonly used, for example, when addressing MIB issues.




















Jonsson                      Informational                      [Page 1]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  2
   2.  Terminology. . . . . . . . . . . . . . . . . . . . . . . . . .  3
   3.  ROHC External Terminology. . . . . . . . . . . . . . . . . . .  6
       3.1.  Network Elements and IP Interfaces . . . . . . . . . . .  6
       3.2.  Channels . . . . . . . . . . . . . . . . . . . . . . . .  7
       3.3.  A Unidirectional Point-to-Point Link Example . . . . . .  8
       3.4.  A Bi-directional Point-to-Point Link Example . . . . . .  8
       3.5.  A Bi-directional Multipoint Link Example . . . . . . . .  9
       3.6.  A Multi-Channel Point-to-Point Link Example. . . . . . .  9
   4.  ROHC Instances . . . . . . . . . . . . . . . . . . . . . . . . 10
       4.1.  ROHC Compressors . . . . . . . . . . . . . . . . . . . . 11
       4.2.  ROHC Decompressors . . . . . . . . . . . . . . . . . . . 12
   5.  ROHC Channels. . . . . . . . . . . . . . . . . . . . . . . . . 13
   6.  ROHC Feedback Channels . . . . . . . . . . . . . . . . . . . . 14
       6.1.  Single-Channel Dedicated ROHC FB Channel Example . . . . 14
       6.2.  Piggybacked/Interspersed ROHC FB Channel Example . . . . 15
       6.3.  Dual-Channel Dedicated ROHC FB Channel Example . . . . . 16
   7.  ROHC Contexts. . . . . . . . . . . . . . . . . . . . . . . . . 17
   8.  Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
   9.  Implementation Implications. . . . . . . . . . . . . . . . . . 18
   10. Security Considerations. . . . . . . . . . . . . . . . . . . . 19
   11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 19
   12. Informative References . . . . . . . . . . . . . . . . . . . . 19
   13. Author's Address . . . . . . . . . . . . . . . . . . . . . . . 19
   14. Full Copyright Statement . . . . . . . . . . . . . . . . . . . 20

1.  Introduction

   In RFC 3095, the RObust Header Compression (ROHC) standard framework
   is defined, along with 4 compression profiles [RFC-3095].  Various
   concepts are introduced within the standard that are not all very
   extensively defined and described, which can easily be an obstacle
   when trying to understand the standard.  This can especially be the
   case when one considers how the various parts of ROHC relate to the
   surrounding environments where header compression may be used.

   The purpose of this document is to clarify these aspects of ROHC
   through examples and additional terminology, discussing terms such as
   ROHC instances, ROHC channels, ROHC feedback, and ROHC contexts.
   This especially means to clarify how these terms relate to other
   terms, such as network elements and IP interfaces, which are commonly
   used for example when addressing MIB issues.  One explicit goal of
   this document is to support and simplify the ROHC MIB development
   work.





Jonsson                      Informational                      [Page 2]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


   The main part of this document, sections 3 to 8, focuses on
   clarifying the conceptual aspects, entity relationships, and
   terminology of ROHC [RFC-3095].  Section 9 explains some
   implementation implications that arise from these conceptual aspects.

2.  Terminology

   ROHC instance

      A logical entity that performs header compression or decompression
      according to one or several ROHC profiles can be referred to as a
      ROHC instance.  A ROHC instance is either a ROHC compressor
      instance or a ROHC decompressor instance.  See section 4.

   ROHC compressor instance

      A ROHC compressor instance is a logical entity that performs
      header compression according to one or several ROHC profiles.
      There is a one-to-one relation between a ROHC compressor instance
      and a ROHC channel, where the ROHC compressor is located at the
      input end of the ROHC channel.  See section 4.1.

   ROHC decompressor instance

      A ROHC decompressor instance is a logical entity that performs
      header decompression according to one or several ROHC profiles.
      There is a one-to-one relation between a ROHC decompressor
      instance and a ROHC channel, where the ROHC decompressor is
      located at the output end of the ROHC channel.  See section 4.2.

   Corresponding decompressor

      When talking about a compressor's corresponding decompressor, this
      refers to the peer decompressor located at the other end of the
      ROHC channel to which the compressor sends compressed header
      packets, i.e., the decompressor that decompresses the headers
      compressed by the compressor.

   Corresponding compressor

      When talking about a decompressor's corresponding compressor, this
      refers to the peer compressor located at the other end of the ROHC
      channel from which the decompressor receives compressed header
      packets, i.e., the compressor that compresses the headers the
      decompressor decompresses.






Jonsson                      Informational                      [Page 3]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


   ROHC peers

      A ROHC compressor and its corresponding ROHC decompressor are
      referred to as ROHC peers.

   Link

      A communication path between two network entities is, in this
      document, generally referred to as a link.

   Bi-directional compression

      If there are means to send feedback information from a
      decompressor to its corresponding compressor, the compression
      performance can be improved.  This way of operating, utilizing the
      feedback possibility for improved compression performance, is
      referred to as bi-directional compression.

   Unidirectional compression

      If there are no means to send feedback information from a
      decompressor to its corresponding compressor, the compression
      performance might not be as good as if feedback could be utilized.
      This way of operating, without making use of feedback for improved
      compression performance, is referred to as unidirectional
      compression.

   ROHC channel

      When a ROHC compressor has transformed original packets into ROHC
      packets with compressed headers, these ROHC packets are sent to
      the corresponding decompressor through a logical point-to-point
      connection dedicated to that traffic.  Such a logical channel,
      which only has to carry data in this single direction from
      compressor to decompressor, is referred to as a ROHC channel.  See
      section 5.

   ROHC feedback channel

      To allow bi-directional compression operation, a logical point-
      to-point connection must be provided for feedback data from the
      decompressor to its corresponding compressor.  Such a logical
      channel, which only has to carry data in the single direction from
      decompressor to compressor, is referred to as a ROHC feedback
      channel.  See section 6.






Jonsson                      Informational                      [Page 4]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


   Co-located compressor/decompressor

      A minimal ROHC instance is only a compressor or a decompressor,
      communicating with a corresponding decompressor or compressor peer
      at the other end of a ROHC channel, thus handling packet streams
      sent in one direction over the link.  However, in many cases, the
      link will carry packet streams in both directions, and it would
      then be desirable to also perform header compression in both
      directions.  That would require both a ROHC compressor and a ROHC
      decompressor at each end of the link, each referred to as a co-
      located compressor/decompressor pair.

   Associated compressor/decompressor

      If there is a co-located ROHC compressor/decompressor pair at each
      end of a link, feedback messages can be transmitted from a ROHC
      decompressor to its corresponding compressor by creating a virtual
      ROHC feedback channel among the compressed header packets sent
      from the co-located ROHC compressor to the decompressor co-located
      with the compressor at the other end.  When a co-located ROHC
      compressor/decompressor pair is connected for this purpose, they
      are said to be associated with each other.

   Interspersed feedback

      Feedback from a ROHC decompressor to a ROHC compressor can either
      be sent on a separate ROHC feedback channel dedicated to feedback
      packets, or sent among compressed header packets going in the
      opposite direction from a co-located (associated) compressor to a
      similarly co-located decompressor at the other end of the link.
      If feedback packets are transmitted in the latter way and sent as
      stand-alone packets, this is referred to as interspersed feedback.
      See section 6.2 for an example.

   Piggybacked feedback

      Feedback from a ROHC decompressor to a ROHC compressor can either
      be sent on a separate ROHC feedback channel dedicated to feedback
      packets, or sent among compressed header packets going in the
      opposite direction from a co-located (associated) compressor to a
      similarly co-located decompressor at the other end of the link.
      If feedback packets are transmitted in the latter way and sent
      encapsulated within compressed header packets going in the other
      direction, this is referred to as piggybacked feedback.  See
      section 6.2 for an example.






Jonsson                      Informational                      [Page 5]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


   Dedicated feedback channel

      A dedicated feedback channel is a logical layer two channel from a
      ROHC decompressor to a ROHC compressor, used only to transmit
      feedback packets.  See sections 6.1 and 6.3 for examples.

3.  ROHC External Terminology

   When considering aspects of ROHC that relate to the surrounding
   networking environment where header compression may be applied,
   unnecessary confusion is easily created because a common, well
   understood, and well defined, terminology is missing.  One major goal
   with this document is to define the preferred terminology to use when
   discussing header compression network integration issues.

3.1.  Network Elements and IP Interfaces

   Header compression is applied over certain links, between two
   communicating entities in a network.  Such entities may be referred
   to as "nodes", "network devices", or "network elements", all terms
   usually having the same meaning.  However, practice within the area
   of network management favors using the term "network element", which
   is therefore consistently used throughout the rest of this document.

   A network element communicates through one or several network
   interfaces, which are often subject to network management, as defined
   by MIB specifications.  In all IP internetworking, each such
   interface has its own IP identity, providing a common network
   interface abstraction, independent of the link technology hidden
   below the interface.  Throughout the rest of this document, such
   interfaces will be referred to as "IP interfaces".

   Thus, to visualize the above terms, the top level hierarchy of a
   network element is as follows, with one or several IP interfaces:

         +-----------------------------------------------------+
         |                   Network Element                   |
         +---------------+--+---------------+------------------+
         |      IP       |  |      IP       |
         |   Interface   |  |   Interface   |
         +---------------+  +---------------+ ...

   The next section builds on this top level hierarchy by looking at
   what is below an IP interface.







Jonsson                      Informational                      [Page 6]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


3.2.  Channels

   As mentioned in the previous section, an IP interface can be
   implemented on top of almost any link technology, although different
   link technologies have different characteristics, and provide
   communication by different means.  However, all link technologies
   provide the common capability to send and/or receive data to/from the
   IP interface.  A generic way of visualizing the common ability to
   communicate is to envision it as one or several logical communication
   channels provided by the link, where each channel can be either bi-
   directional or unidirectional.  Such logical point-to-point
   connections will, throughout the rest of this document, be referred
   to as "channels", either bi-directional or unidirectional.  Note that
   this definition of "channels" is less restrictive than the definition
   of "ROHC channels", as given in section 5.

   Extending the above network element hierarchy with the concept of
   channels would then lead to the following:

         +-----------------------------------------------------+
         |                   Network Element                   |
         +---------------+--+---------------+------------------+
         |      IP       |  |      IP       |
         |   Interface   |  |   Interface   |
         ++ +-+ +-+ +----+  ++ +-+ +-+ +----+ ...
          |C| |C| |C|        |C| |C| |C|
          |h| |h| |h|        |h| |h| |h|
          |a| |a| |a|        |a| |a| |a|
          |n| |n| |n| ...    |n| |n| |n| ...
          |n| |n| |n|        |n| |n| |n|
          |e| |e| |e|        |e| |e| |e|
          |l| |l| |l|        |l| |l| |l|
          : : : : : :        : : : : : :

   Whether there is more than one channel, and whether the channel(s)
   is/are bi-directional or unidirectional (or a mix of both) is link
   technology dependent, as is the way in which channels are logically
   created.

   The following subsections, 3.3-3.6, give a number of different link
   examples, and relate these to the general descriptions above.
   Further, each section discusses how header compression might be
   applied in that particular case.  The core questions for header
   compression are:

   -  Are channels bi- or unidirectional?
   -  Is the link point-to-point?  If not, a lower layer addressing
      scheme is needed to create logical point-to-point channels.



Jonsson                      Informational                      [Page 7]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


   Note that these subsections talk about header compression in general,
   while later sections will address the case of ROHC in more detail.
   Further, one should remember that in the later sections, the general
   channel definition is slightly enhanced for header compression by the
   definition of the ROHC channel (section 5) and the ROHC feedback
   channel (section 6), while here the basic channel concept is used, as
   defined above.

3.3.  A Unidirectional Point-to-Point Link Example

   The simplest possible link example one can derive from the general
   overview above is the case with one single unidirectional channel
   between two communicating network elements.

         +-----------------+                  +-----------------+
         | Network Element |                  | Network Element |
         +-----------------+                  +-----------------+
         |       IP        |                  |       IP        |
         |    Interface    |                  |    Interface    |
         +------+   +------+                  +------+   +------+
                |   |                                |   |
                |   +--------------------------------+   |
                |     ->  Unidirectional channel  ->     |
                +----------------------------------------+

   A typical example of a point-to-point link with one unidirectional
   channel like this is a satellite link.  Since there is no return path
   present, only unidirectional header compression can be applied here.

3.4.  A Bi-directional Point-to-Point Link Example

   Taking the above example one step further, the natural extension
   would be an example with one single bi-directional channel between
   two communicating network elements.  In this example, there are still
   only two endpoints and one single channel, but the channel is simply
   enhanced to allow bi-directional communication.

         +-----------------+                  +-----------------+
         | Network Element |                  | Network Element |
         +-----------------+                  +-----------------+
         |       IP        |                  |       IP        |
         |    Interface    |                  |    Interface    |
         +------+   +------+                  +------+   +------+
                |   |                                |   |
                |   +--------------------------------+   |
                |    <->  Bi-directional channel  <->    |
                +----------------------------------------+




Jonsson                      Informational                      [Page 8]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


   A typical example of a point-to-point link with such a bi-directional
   channel is a PPP modem connection over a regular telephone line.
   Header compression can easily be applied here as well, as is usually
   done over e.g., PPP, and the compression scheme can make use of the
   return path to improve compression performance.

3.5.  A Bi-directional Multipoint Link Example

   Leaving the simple point-to-point link examples, this section
   addresses the case of a bi-directional link connecting more than two
   communicating network elements.  To simplify the example, the case
   with three endpoints is considered.

      +-----------------+   +-----------------+   +-----------------+
      | Network Element |   | Network Element |   | Network Element |
      +-----------------+   +-----------------+   +-----------------+
      |       IP        |   |       IP        |   |       IP        |
      |    Interface    |   |    Interface    |   |    Interface    |
      +------+   +------+   +------+   +------+   +------+   +------+
             |   |                 |   |                 |   |
             |   |                 |   |                 |   |
             |   +-----------------+   +-----------------+   |
             |   <->  Bi-directional "shared channel"  <->   |
             +-----------------------------------------------+

   A typical example of a multipoint link with such a bi-directional
   "shared channel" is an Ethernet.  Since the channel is shared,
   applying header compression would require a lower layer addressing
   scheme to provide logical point-to-point channels, according to the
   definition of "channels".

   As an aside, it should be noted that a case of unidirectional
   multipoint links is basically the same as a number of unidirectional
   point-to-point links.  In such a case, each receiver only sees one
   single sender, and the sender's behavior is independent of the number
   of receivers and is unaffected by their behavior.

3.6.  A Multi-Channel Point-to-Point Link Example

   This final example addresses a scenario which is expected to be
   typical in many environments where ROHC will be applied.  The key
   point of the example is the multi-channel property, which is common
   in, for example, cellular environments.  Data through the same IP
   interface might here be transmitted on different channels, depending
   on its characteristics.  In the following example, there are three
   channels present, one bi-directional, and one unidirectional in each
   direction, but the channel configuration could of course be
   arbitrary.



Jonsson                      Informational                      [Page 9]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


      +-----------------+                      +-----------------+
      | Network Element |                      | Network Element |
      +-----------------+                      +-----------------+
      |       IP        |                      |       IP        |
      |    Interface    |                      |    Interface    |
      +-+ +---+ +---+ +-+                      +-+ +---+ +---+ +-+
        | |   | |   | |                          | |   | |   | |
        | |   | |   | +--------------------------+ |   | |   | |
        | |   | |   | <- Unidirectional channel <- |   | |   | |
        | |   | |   +------------------------------+   | |   | |
        | |   | |                                      | |   | |
        | |   | |                                      | |   | |
        | |   | +--------------------------------------+ |   | |
        | |   |      <-> Bi-directional channel <->      |   | |
        | |   +------------------------------------------+   | |
        | |                                                  | |
        | |                                                  | |
        | +--------------------------------------------------+ |
        |             -> Unidirectional channel ->             |
        +------------------------------------------------------+

   As mentioned above, a typical example of a multi-channel link is a
   cellular wireless link.  In this example, header compression would be
   applicable on a per-channel basis, for each channel operating either
   in a bi-directional or unidirectional manner, depending on the
   channel properties.

4.  ROHC Instances

   For various purposes, such as network management on an IP interface
   implementing ROHC, it is necessary to identify the various ROHC
   entities that might be present on an interface.  Such a minimal ROHC
   entity will, from now on, be referred to as a "ROHC instance".  A
   ROHC instance can be one of two different types, either a "ROHC
   compressor" or a "ROHC decompressor" instance, and an IP interface
   can have N ROHC compressors and M ROHC decompressors, where N and M
   are arbitrary numbers.  It should be noted that although a compressor
   is often co-located with a decompressor, a ROHC instance can never
   include both a compressor and a decompressor; where both are present,
   they will be referred to as two ROHC instances.

   The following two subsections describe the two kinds of ROHC
   instances and their external interfaces, while sections 5 and 6
   address how communication over these interfaces is realized through
   "ROHC channels" and "ROHC feedback channels".  Section 7 builds on
   top of the instance, channel and feedback channel concepts, and
   clarifies how ROHC contexts map to this.




Jonsson                      Informational                     [Page 10]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


   It should be noted that all figures in sections 4-6 have been rotated
   90 degrees to simplify drawing, i.e., they do not show a "stack
   view".

4.1.  ROHC Compressors

   A ROHC compressor instance supports header compression according to
   one or several ROHC profiles.  Apart from potential configuration or
   control interfaces, a compressor instance receives and sends data
   through 3 inputs and 1 output, as illustrated by the figure below:

                               +--------------+
                      -> UI -> |              | -> CO ->
                               |     ROHC     |
                               |  Compressor  |
                      -> PI -> |              | <- FI <-
                               +--------------+

      Uncompressed Input (UI): Uncompressed packets are delivered from
                               higher layers to the compressor through
                               the UI.

      Compressed Output (CO):  Compressed packets are sent from the
                               compressor through the CO, which is
                               always connected to the input end of a
                               ROHC channel (see section 5).

      Feedback Input (FI):     Feedback from the corresponding
           [optional]          decompressor is received by the
                               compressor through the FI, which (if
                               present) is connected to the output end
                               of a ROHC feedback channel of some kind
                               (see section 6).  When there are no
                               means to transmit feedback from
                               decompressor to compressor, FI is not
                               used, and bi-directional compression
                               will not be possible.

      Piggyback Input (PI):    If the compressor is associated with a
           [optional]          co-located decompressor, for which the
                               compressor delivers feedback to the
                               other end of the link, feedback data
                               for piggybacking is delivered to the
                               compressor through the PI.  If this input
                               is used, it is connected to the FO of the
                               co-located decompressor (see section
                               4.2).




Jonsson                      Informational                     [Page 11]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


4.2.  ROHC Decompressors

   A ROHC decompressor instance supports header decompression according
   to one or several ROHC profiles.  Apart from potential configuration
   or control interfaces, a decompressor instance receives and sends
   data through 1 input and 3 outputs, as illustrated by the figure
   below:

                               +--------------+
                      -> CI -> |              | -> DO ->
                               |     ROHC     |
                               | Decompressor |
                      <- FO <- |              | -> PO ->
                               +--------------+

      Compressed Input (CI):    Compressed packets are received by the
                                decompressor through the CI, which is
                                always connected to the output end of a
                                ROHC channel (see section 5).

      Decompressed Output (DO): Decompressed packets are delivered from
                                the decompressor to higher layers
                                through the DO.

      Feedback Output (FO):     Feedback to the corresponding compressor
           [optional]           is sent from the compressor through the
                                FO, which (if present) is connected to
                                the input end of a ROHC feedback channel
                                of some kind (see section 6).  When
                                there are no means to transmit feedback
                                from decompressor to compressor, FO is
                                not used, and bi-directional compression
                                will not be possible.

      Piggyback Output (PO):    If the decompressor is associated with
           [optional]           a co-located compressor to which the
                                decompressor delivers feedback it
                                receives piggybacked from the other end
                                of the link, the received feedback data
                                is delivered from the decompressor
                                through the PO.  If this output is used,
                                it is connected to the FI of the co-
                                located compressor (see section 4.1).








Jonsson                      Informational                     [Page 12]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


5.  ROHC Channels

   In section 3, a general concept of channels was introduced.
   According to that definition, a channel is basically a logical
   point-to-point connection between the IP interfaces of two
   communicating network elements.  By that definition, a channel
   represents the kind of logical connection needed to make header
   compression generally applicable, and then the channel properties
   control whether compression can operate in a unidirectional or bi-
   directional manner.

   The channel concept thus facilitates general header compression
   discussions, but since it groups unidirectional and bi-directional
   connections together, it does not provide the means for describing
   details of how ROHC logically works.  Therefore, for the case of
   ROHC, the channel concept is enhanced and a more restricted concept
   of "ROHC channels" is defined.

   A ROHC channel has the same properties as a channel, with the
   difference that a ROHC channel is always unidirectional.  A ROHC
   channel therefore has one single input endpoint, connected to the CO
   of one single ROHC compressor instance, and one single output
   endpoint, connected to the CI of one single ROHC decompressor
   instance.  A ROHC channel must thus in this way be logically
   dedicated to one ROHC compressor and one ROHC decompressor, hereafter
   referred to as ROHC peers, creating a one-to-one mapping between a
   ROHC channel and two ROHC compressor/decompressor peers.

   +--------------+          --->-->-->-->---          +--------------+
   |              | -> CO ->   ROHC Channel   -> CI -> |              |
   |     ROHC     |          --->-->-->-->---          |     ROHC     |
   |  Compressor  |                                    | Decompressor |
   |              |                                    |              |
   +--------------+                                    +--------------+

   In many cases the lower layer channel is by nature bi-directional,
   but for ROHC communication over that channel, a ROHC channel would
   only represent one communication direction of that channel.  For bi-
   directional channels, a common case would be to logically allocate
   one ROHC channel in each direction, allowing ROHC compression to be
   performed in both directions.  The reason for defining ROHC channels
   as unidirectional is basically to separate and generalize the concept
   of feedback, as described and exemplified in section 6.








Jonsson                      Informational                     [Page 13]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


6.  ROHC Feedback Channels

   Since ROHC can be implemented over various kinds of links,
   unidirectional or bi-directional one-channel links, as well as
   multi-channel links, the logical transmission of feedback from
   decompressor to compressor has been separated out from the transport
   of actual ROHC packets through the definition of ROHC channels as
   always being unidirectional from compressor to decompressor.  This
   means that an additional channel concept must be defined for
   feedback, which is what will hereafter be referred to as "ROHC
   feedback channels".

   In the same way as a ROHC channel is a logically dedicated
   unidirectional channel from a ROHC compressor to its corresponding
   ROHC peer decompressor, a ROHC feedback channel is a logically
   dedicated unidirectional channel from a ROHC decompressor to its
   corresponding ROHC peer compressor.  A ROHC feedback channel thus has
   one single input endpoint, connected to the FO of one single ROHC
   decompressor instance, and one single output endpoint, connected to
   the FI of one single ROHC compressor instance.

   +--------------+                                     +--------------+
   |              |                                     |              |
   |     ROHC     |                                     |     ROHC     |
   |  Compressor  |          --<--<--<--<--<--          | Decompressor |
   |              | <- FI <-  ROHC FB Channel  <- FO <- |              |
   +--------------+          --<--<--<--<--<--          +--------------+

   The reason for making this simplification and logically separating
   ROHC channels from ROHC feedback channels is generality for handling
   of feedback.  ROHC has been designed with the assumption of logical
   separation, which creates flexibility in realizing feedback
   transport, as discussed in [RFC-3095, section 5.2.1].  There are no
   restrictions on how to implement a ROHC feedback channel, other than
   that it must be made available and be logically dedicated to the ROHC
   peers if bi-directional compression operation is to be allowed.

   The following subsections provide some, not at all exhaustive,
   examples of how a ROHC feedback channel might possibly be realized.

6.1.  Single-Channel Dedicated ROHC Feedback Channel Example

   This section illustrates a one-way compression example where one bi-
   directional channel has been configured to represent a ROHC channel
   in one direction and a dedicated ROHC feedback channel in the other
   direction.





Jonsson                      Informational                     [Page 14]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


                          Bi-directional channel
                            ..................
       +--------------+     : -->-->-->-->-- :     +--------------+
   --> |UI          CO| --> :  ROHC Channel  : --> |CI          DO| -->
       |     ROHC     |     : -->-->-->-->-- :     |     ROHC     |
       |  Compressor  |     :                :     | Decompressor |
       |              |     : --<--<--<--<-- :     |              |
     o |PI          FI| <-- :   FB Channel   : <-- |FO          PO| o
       +--------------+     : --<--<--<--<-- :     +--------------+
                            :................:

   In this example, feedback is sent on its own dedicated channel, as
   discussed in e.g., feedback realization example 1-3 of ROHC [RFC-
   3095, page 44].  This means that the piggybacking/interspersing
   mechanism of ROHC is not used, and the PI/PO connections are thus
   left open (marked with a "o").  To facilitate communication with ROHC
   compression in a two-way manner using this approach, an identical
   configuration must be provided for the other direction, i.e., making
   use of four logical unidirectional channels.

6.2.  Piggybacked/Interspersed ROHC Feedback Channel Example

   This section illustrates how a bi-directional channel has been
   configured to represent one ROHC channel in each direction, while
   still allowing feedback to be transmitted through ROHC piggybacking
   and interspersing.

                          Bi-directional channel
                            ..................
       +--------------+     : -->-->-->-->-- :     +--------------+
   --> |UI          CO| --> : ROHC Channel A : --> |CI          DO| -->
       |     ROHC     |     : -->-->-->-->-- :     |     ROHC     |
       |  Compressor  |     :                :     | Decompressor |
       |      A       |     :                :     |      A       |
   +-> |PI          FI| <-+ :                : +-- |PO          FO| --+
   |   +--------------+   | :                : |   +--------------+   |
   |                      | :                : |                      |
   |                      | :                : |                      |
   |   +--------------+   | :                : |   +--------------+   |
   +-- |FO          PO| --+ :                : +-> |FI          PI| <-+
       |     ROHC     |     :                :     |     ROHC     |
       | Decompressor |     :                :     |  Compressor  |
       |      B       |     : --<--<--<--<-- :     |      B       |
   <-- |DO          CI| <-- : ROHC Channel B : <-- |CO          UI| <--
       +--------------+     : --<--<--<--<-- :     +--------------+
                            :................:





Jonsson                      Informational                     [Page 15]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


   In this example, feedback is transmitted piggybacked or interspersed
   among compressed header packets in the ROHC channels, as discussed in
   e.g., feedback realization example 4-6 of ROHC [RFC-3095, page 44].
   Feedback from decompressor A to compressor A is here sent through
   FO(A)->PI(B), piggybacked on a compressed packet over ROHC channel B,
   and delivered to compressor A through PO(B)->FI(A).  A logical ROHC
   feedback channel is thus provided from the PI input at compressor B
   to the PO output at decompressor B.  It should be noted that in this
   picture, PO and FO at the decompressors have been swapped to simplify
   drawing.

6.3.  Dual-Channel Dedicated ROHC Feedback Channel Example

   This section illustrates how two bi-directional channels have been
   configured to represent two ROHC channels and two dedicated ROHC
   feedback channels, respectively.

                          Bi-directional channel
                            ..................
       +--------------+     : -->-->-->-->-- :     +--------------+
     ->|UI          CO| --> : ROHC Channel A : --> |CI          DO|->
       |     ROHC     |     : -->-->-->-->-- :     |     ROHC     |
       |  Compressor  |     :                :     | Decompressor |
       |      A       |     :                :     |      A       |
       |              |     :                :     |              |
   +-> |FI          PI| o   :                :   o |PO          FO| --+
   |   +--------------+     : --<--<--<--<-- :     +--------------+   |
   |                     +- : ROHC Channel B :<-+                     |
   |                     |  : --<--<--<--<-- :  |                     |
   |   +--------------+  |  :................:  |  +--------------+   |
   | <-|DO          CI|<-+                      +- |CO          UI|<- |
   |   |     ROHC     |                            |     ROHC     |   |
   |   | Decompressor |   Bi-directional channel   |  Compressor  |   |
   |   |      B       |     ..................     |      B       |   |
   |   |              |     : -->-->-->-->-- :     |              |   |
   |  o|PO          FO| --> :  FB Channel B  : --> |FI          PI|o  |
   |   +--------------+     : -->-->-->-->-- :     +--------------+   |
   |                        :                :                        |
   |                        : --<--<--<--<-- :                        |
   +----------------------- :  FB Channel A  : <----------------------+
                            : --<--<--<--<-- :
                            :................:

   In this example, feedback is, in both directions, sent on its own
   dedicated channel, as discussed in e.g., feedback realization example
   1-3 of ROHC [RFC-3095, page 44].  With this configuration, the
   piggybacking/interspersing mechanism of ROHC is not used, and the
   PI/PO connections are thus left open (marked with a "o").  It should



Jonsson                      Informational                     [Page 16]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


   be noted that in this picture FI/PI and PO/FO at the A-instances have
   been swapped to simplify drawing, while the B-instances have been
   horizontally mirrored.

7.  ROHC Contexts

   In previous sections, it has been clarified that one network element
   may have multiple IP interfaces, one IP interface may have multiple
   ROHC instances running (not necessarily both compressors and
   decompressors), and for each ROHC instance, there is exactly one ROHC
   channel and optionally one ROHC feedback channel.  How ROHC channels
   and ROHC feedback channels are realized will differ from case to
   case, depending on the actual layer two technology used.

   Each compressor/decompressor can further compress/decompress an
   arbitrary (but limited) number of concurrent packet streams sent over
   the ROHC channel connected to that compressor/decompressor.  Each
   packet stream relates to one particular context in the
   compressor/decompressor.  When sent over the ROHC channel, compressed
   packets are labeled with a context identifier (CID), indicating to
   which context the compressed packet corresponds.  There is thus a
   one-to-one mapping between the number of contexts that can be present
   in a compressor/decompressor and the context identifier (CID) space
   used in compressed packets over that ROHC channel.  This is
   illustrated by the following figure:

    +------------------------------------------------------------------+
    |                           IP Interface                           |
    +---------------+----+---------------+----+---------------+--------+
    |     ROHC      |    |     ROHC      |    |     ROHC      |
    |  Compressor   |    |  Compressor   |    | Decompressor  |
    | Context 0...N |    | Context 0...M |    | Context 0...K |  ...
    +--+---------+--+    +--+---------+--+    +--+---------+--+
       ^         |          ^         |          :         ^
       :   CID   |          :   CID   |          :   CID   |
       :  0...N  |          :  0...M  |          :  0...K  |
       :         v          :         v          v         |
     ROHC      ROHC       ROHC      ROHC       ROHC      ROHC
   Feedback   Channel   Feedback   Channel   Feedback   Channel
    Channel              Channel              Channel

   It should be noted that each ROHC instance at an IP interface
   therefore has its own context and CID space, and it must be ensured
   that the CID size of the corresponding decompressor at the other end
   of the ROHC channel is not smaller than the CID space of the
   compressor.





Jonsson                      Informational                     [Page 17]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


8.  Summary

   This document has introduced and defined a number of concepts and
   terms for use in ROHC network integration, and explained how the
   various pieces relate to each other.  In the following bullet list,
   the most important relationship conclusions are repeated:

   -  A network element may have one or several IP interfaces.

   -  Each IP interface is connected to one or several logical layer two
      channels.

   -  Each IP interface may have one or several ROHC instances, either
      compressors, decompressors, or an arbitrary mix of both.

   -  For each ROHC instance, there is exactly one ROHC channel, and
      optionally exactly one ROHC feedback channel.

   -  How ROHC channels and ROHC feedback channels are realized through
      the available logical layer two channels will vary, and there is
      therefore no general relation between ROHC instances and logical
      layer two channels.  ROHC instances map only to ROHC channels and
      ROHC feedback channels.

   -  Each compressor owns its own context identifier (CID) space, which
      is the multiplexing mechanism it uses when sending compressed
      header packets to its corresponding decompressor.  That CID space
      thus defines how many compressed packet streams can be
      concurrently sent over the ROHC channel allocated to the
      compressor/decompressor peers.

9.  Implementation Implications

   This section will address how the conceptual aspects discussed above
   affect implementations of ROHC.

   ROHC is defined as a general header compression framework on top of
   which compression profiles can be defined for each specific set of
   headers to compress.  Although the framework holds a number of
   important mechanisms, the separation between framework and profiles
   is mainly a separation from a standardization point of view, to
   indicate what must be common to all profiles, what must be defined by
   all profiles, and what are profile-specific details.  To implement
   the framework as a separate module is thus not an obvious choice,
   especially if one wants to use profile implementations from different
   vendors.  However, optimized implementations will probably separate
   the common parts and implement those in a ROHC framework module, and
   add profile modules to that.



Jonsson                      Informational                     [Page 18]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


   A ROHC instance might thus consist of various pieces of
   implementation modules, profiles, and potentially also a common ROHC
   module, possibly from different vendors.  If vendor and
   implementation version information is made available for network
   management purposes, this should thus be done on a per-profile basis,
   and potentially also for the instance as a whole.

10.  Security Considerations

   The clear understanding of ROHC channels and their relations to IP
   interfaces and the physical medium, plays a critical role in ensuring
   secure usage of ROHC.  This document is therefore a valuable adjunct
   to the Security Considerations found in RFC 3095 and other ROHC
   specifications.  However, as it just reviews information and
   definitions, it does not add new security issues to the ROHC protocol
   specifications.

11.  Acknowledgements

   Thanks to Juergen Quittek, Hans Hannu, Carsten Bormann, and Ghyslain
   Pelletier for fruitful discussions, improvement suggestions, and
   review.  Thanks also to Peter Eriksson for doing a language review.

12.  Informative References

   [RFC-3095] Bormann, C., Burmeister, C., Degermark, M., Fukushima, H.,
              Hannu, H., Jonsson, L-E., Hakenberg, R., Koren, T., Le,
              K., Liu, Z., Martensson, A., Miyazaki, A., Svanbro, K.,
              Wiebke, T., Yoshimura, T. and H. Zheng, "RObust Header
              Compression (ROHC): Framework and four profiles: RTP, UDP,
              ESP, and uncompressed", RFC 3095, July 2001.

13.  Author's Address

   Lars-Erik Jonsson
   Ericsson AB
   Box 920
   SE-971 28 Lulea
   Sweden

   Phone: +46 920 20 21 07
   Fax:   +46 920 20 20 99
   EMail: lars-erik.jonsson@ericsson.com








Jonsson                      Informational                     [Page 19]


RFC 3759     ROHC Terminology and Channel Mapping Examples    April 2004


14.  Full Copyright Statement

   Copyright (C) The Internet Society (2004).  This document is subject
   to the rights, licenses and restrictions contained in BCP 78, and
   except as set forth therein, the authors retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at ietf-
   ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.









Jonsson                      Informational                     [Page 20]