This is a purely informative rendering of an RFC that includes verified errata. This rendering may not be used as a reference.

The following 'Verified' errata have been incorporated in this document: EID 334
Network Working Group                                          R. Woundy
Request for Comments: 3083                                 Cisco Systems
Category: Informational                                       March 2001


         Baseline Privacy Interface Management Information Base
 for DOCSIS Compliant Cable Modems and Cable Modem Termination Systems

Status of this Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2001).  All Rights Reserved.

Abstract

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it defines a basic set of managed objects for SNMP-
   based (Simple Network Management Protocol) management of the Baseline
   Privacy Interface (BPI), which provides data privacy for DOCSIS 1.0
   (Data-Over-Cable Service Interface Specifications) compliant Cable
   Modems and Cable Modem Termination Systems.  This MIB is defined as
   an extension to the DOCSIS Radio Frequency Interface MIB, RFC 2670.

   This memo specifies a MIB module in a manner that is compliant to the
   SMIv2 (Structure of Management Information Version 2).  The set of
   objects is consistent with the SNMP framework and existing SNMP
   standards.

   CableLabs requires the implementation of this MIB in DOCSIS 1.0 cable
   modems that implement the Baseline Privacy Interface, as a
   prerequisite for DOCSIS 1.0 certification.

Table of Contents

   1 The SNMP Management Framework ................................... 2
   2 Glossary ........................................................ 3
   2.1 Authorization key ............................................. 3
   2.2 BPI ........................................................... 4
   2.3 BPI+ .......................................................... 4
   2.4 CATV .......................................................... 4
   2.5 CM ............................................................ 4
   2.6 CMTS .......................................................... 4
   2.7 DOCSIS ........................................................ 4
   2.8 Downstream .................................................... 4
   2.9 Head-end ...................................................... 4
   2.10 MAC Packet ................................................... 4
   2.11 MCNS ......................................................... 5
   2.12 RF ........................................................... 5
   2.13 SID .......................................................... 5
   2.14 TEK .......................................................... 5
   2.15 Upstream ..................................................... 5
   3 Overview ........................................................ 5
   3.1 Structure of the MIB .......................................... 5
   3.2 Management requirements ....................................... 6
   3.3 Textual convention ............................................ 7
   4 Definitions ..................................................... 8
   5 Acknowledgments ................................................ 40
   6 References ..................................................... 40
   7 Security Considerations ........................................ 42
   8 Intellectual Property .......................................... 43
   9 Author's Address ............................................... 44
   10 Full Copyright Statement ...................................... 45

1.  The SNMP Management Framework

   The SNMP Management Framework presently consists of five major
   components:

   o  An overall architecture, described in RFC 2571 [1].

   o  Mechanisms for describing and naming objects and events for the
      purpose of management.  The first version of this Structure of
      Management Information (SMI) is called SMIv1 and described in STD
      16, RFC 1155 [2], STD 16, RFC 1212 [3] and RFC 1215 [4].  The
      second version, called SMIv2, is described in STD 58, RFC 2578
      [5], RFC 2579 [6] and RFC 2580 [7].

   o  Message protocols for transferring management information.  The
      first version of the SNMP message protocol is called SNMPv1 and
      described in STD 15, RFC 1157 [8].  A second version of the SNMP

      message protocol, which is not an Internet standards track
      protocol, is called SNMPv2c and described in RFC 1901 [9] and RFC
      1906 [10].  The third version of the message protocol is called
      SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and RFC 2574
      [12].

   o  Protocol operations for accessing management information. The
      first set of protocol operations and associated PDU formats is
      described in STD 15, RFC 1157 [8].  A second set of protocol
      operations and associated PDU formats is described in RFC 1905
      [13].

   o  A set of fundamental applications described in RFC 2573 [14] and
      the view-based access control mechanism described in RFC 2575
      [15].

   A more detailed introduction to the current SNMP Management Framework
   can be found in RFC 2570 [24].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  Objects in the MIB are
   defined using the mechanisms defined in the SMI.

   This memo specifies a MIB module that is compliant to the SMIv2.  A
   MIB conforming to the SMIv1 can be produced through the appropriate
   translations.  The resulting translated MIB must be semantically
   equivalent, except where objects or events are omitted because no
   translation is possible (use of Counter64).  Some machine readable
   information in SMIv2 will be converted into textual descriptions in
   SMIv1 during the translation process.  However, this loss of machine
   readable information is not considered to change the semantics of the
   MIB.

2.  Glossary

   The terms in this document are derived either from normal cable
   system usage, or from the documents associated with the Data Over
   Cable Service Interface Specification process.

2.1.  Authorization key

   A key used to derive a key encryption key (used to encrypt TEKs), and
   to derive message authentication keys.  When the CMTS communicates
   the authorization key to the CM, it encrypts the authorization key
   using the RSA public key of the CM [22].

2.2.  BPI - Baseline Privacy Interface

   A term referring to the DOCSIS specification [18] for enabling simple
   data privacy in the DOCSIS 1.0 system.  Management of the BPI is the
   focus of this document.

2.3.  BPI+ - Baseline Privacy Plus Interface

   A term referring to the DOCSIS specification [21] for enabling CM
   authentication and data privacy in the DOCSIS 1.1 system.  Management
   of the BPI+ is not addressed in this document.

2.4.  CATV

   Originally "Community Antenna Television", now used to refer to any
   cable or hybrid fiber and cable system used to deliver video signals
   to a community.

2.5.  CM - Cable Modem

   A CM acts as a "slave" station in a DOCSIS compliant cable data
   system.

2.6.  CMTS - Cable Modem Termination System

   A generic term covering a cable bridge or cable router in a head-end.
   A CMTS acts as the master station in a DOCSIS compliant cable data
   system.  It is the only station that transmits downstream, and it
   controls the scheduling of upstream transmissions by its associated
   CMs.

2.7.  DOCSIS

   "Data-Over-Cable Service Interface Specifications".  A term referring
   to the ITU-T J.112 Annex B standard for cable modem systems [19].

2.8.  Downstream

   The direction from the head-end towards the subscriber.

2.9.  Head-end

   The origination point in most cable systems of the subscriber video
   signals.  Generally also the location of the CMTS equipment.

2.10.  MAC Packet

   A DOCSIS PDU.

2.11.  MCNS

   "Multimedia Cable Network System".  Generally replaced in usage by
   DOCSIS.

2.12.  RF

   Radio Frequency.

2.13  SID

   Service ID.  The SID identifies a particular upstream bandwidth
   allocation and class-of-service management for DOCSIS, and identifies
   a particular bidirectional security association for BPI.

2.14.  TEK - Traffic Encryption Key

   Traffic Encryption Key, which is used for DES encryption of upstream
   and downstream traffic.  When the CMTS communicates the TEK to the
   CM, it encrypts the TEK using the key encryption key derived from the
   authorization key.

2.15.  Upstream

   The direction from the subscriber towards the head-end.

3.  Overview

   This MIB provides a set of objects required for the management of the
   Baseline Privacy Interface for DOCSIS compliant Cable Modems (CMs)
   and Cable Modem Termination Systems (CMTSs).  This MIB specification
   is derived from the DOCSIS Baseline Privacy Interface specification
   [18], which is an extension to the DOCSIS Radio Frequency Interface
   specification [19].

   Please note that this MIB specification is not sufficient for the
   management of the DOCSIS Baseline Privacy Plus Interface
   specification [21].  The working group expects to issue a MIB for the
   management of BPI+ at a later time.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [23].

3.1.  Structure of the MIB

   This MIB consists of one group of CM-only objects (docsBpiCmGroup),
   and one group of CMTS-only objects (docsBpiCmtsGroup).

   The CM-only objects are organized into two tables:

   o  The docsBpiCmBaseTable contains objects for managing basic
      Baseline Privacy parameters and counters, and for managing the
      Authorization finite state machine.

   o  The docsBpiCmTEKTable contains objects for managing the Traffic
      Encryption Key (TEK) finite state machine per SID.

   The CMTS-only objects are organized into four sub-groups:

   o  The docsBpiCmtsBaseTable contains objects for managing basic
      Baseline Privacy parameters and counters.

   o  The docsBpiCmtsAuthTable contains objects for managing the
      Authorization association information per cable modem.

   o  The docsBpiCmtsTEKTable contains objects for managing the TEK
      association information per SID.

   o  The docsBpiMulticastControl consists of two tables.  The
      docsBpiIpMulticastMapTable controls the mapping of downstream IP
      multicast data traffic to downstream multicast SID values.  The
      docsBpiMulticastAuthTable controls which CMs are authorized to
      receive downstream traffic transmitted over particular multicast
      SIDs; a CM will receive TEKs corresponding to the multicast SIDs
      for which it is authorized.  The combination of these two tables
      will limit the distribution of downstream IP multicast data
      traffic to authorized CMs.

3.2.  Management requirements

   The Baseline Privacy Interface specification is documented in [18],
   and is an extension to the Radio Frequency Interface specification
   documented in [19].  In addition to the explicit requirements in this
   specification, the CM and CMTS enabled for Baseline Privacy MUST
   support all applicable DOCSIS and IETF requirements and MIB objects.
   Specifications that identify relevant requirements and MIB objects
   include the IETF Radio Frequency MIB [16], the IETF Cable Device MIB
   [17], and the DOCSIS OSSI Specification [20].

   The explicit management requirements of the Baseline Privacy
   Interface, which motivate the development of the MIB in this
   document, are detailed below:

   o  The CM and CMTS MUST support viewing relevant RSA public keys, for
      future subscriber authentication applications.

   o  The Baseline Privacy management interface needs to support
      operator configuration of Authorization and TEK Finite State
      Machine (FSM) parameters, for performance tuning and security
      incident handling.  The CMTS MUST support viewing (and configuring
      if possible) all FSM-related parameters, including baseline
      privacy status (enabled or disabled), key lifetimes, key grace
      times, and state timeout values.  The CM MUST support viewing
      these parameters where possible.

   o  The management interface needs to support operator analysis and
      override of FSM behavior, for fault management, subscriber service
      de-provisioning, and security incident handling.  The CM MUST
      support viewing the current FSM states.  The CM and CMTS MUST
      support viewing message error codes and message error strings, and
      counters for invalid KEK and TEK events, for key expirations and
      renewals, and for duplicate messages.  The CM and CMTS MUST
      support viewing current authorization key sequence numbers and key
      expiration times for failure diagnosis.

   o  The management interface needs to support dynamic control of the
      distribution of IP multicast data traffic.  This control includes
      forwarding IP multicast traffic to the correct multicast group
      (SID), and managing the membership lists of each multicast group
      (SID).  The CMTS MUST support configuring and viewing all IP
      multicast forwarding state, and all multicast group memberships,
      within the MAC domains of the CMTS.

3.3.  Textual convention

   CableLabs has required the implementation of prior versions of this
   MIB in DOCSIS 1.0 cable modems that implement the Baseline Privacy
   Interface, as a prerequisite for DOCSIS 1.0 certification.

   The Baseline Privacy Interface MIB contains eight MIB objects defined
   with the (now obsolete) DisplayString textual convention, and one MIB
   object defined with the (now undesirable) IpAddress textual
   convention.

   In the judgment of the working group, it is preferable to keep these
   less-than-desirable textual conventions, in order to maintain
   backward compatibility and interoperability with DOCSIS 1.0 cable
   modems that implemented previous versions of this MIB.

4.  Definitions

DOCS-BPI-MIB DEFINITIONS ::= BEGIN

IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
Integer32, Counter32, IpAddress
FROM SNMPv2-SMI
DisplayString, MacAddress, RowStatus, TruthValue, DateAndTime
FROM SNMPv2-TC
OBJECT-GROUP, MODULE-COMPLIANCE
FROM SNMPv2-CONF
ifIndex
FROM IF-MIB
docsIfMib, docsIfCmServiceId, docsIfCmtsServiceId
FROM DOCS-IF-MIB
;

docsBpiMIB      MODULE-IDENTITY
LAST-UPDATED "200103130000Z"
ORGANIZATION "IETF IPCDN Working Group"
CONTACT-INFO "Rich Woundy
              Postal: Cisco Systems
                      250 Apollo Drive
                      Chelmsford, MA 01824 U.S.A.
              Tel: +1 978 244 8000
              E-mail: rwoundy@cisco.com

              IETF IPCDN Working Group
              General Discussion: ipcdn@ietf.org
              Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn
              Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn
              Co-chairs: Richard Woundy, rwoundy@cisco.com
                         Andrew Valentine, a.valentine@eu.hns.com"
DESCRIPTION
"This is the MIB Module for the DOCSIS Baseline Privacy Interface
(BPI) at cable modems (CMs) and cable modem termination systems
(CMTSs). CableLabs requires the implementation of this MIB in
DOCSIS 1.0 cable modems that implement the Baseline Privacy
Interface, as a prerequisite for DOCSIS 1.0 certification."

REVISION "200103130000Z"
DESCRIPTION
"Version published as RFC 3083."

REVISION "200011031930Z"
DESCRIPTION
"Modified by Richard Woundy to fix problems identified by the MIB

doctor. I marked docsBpiCmtsDefaultAuthGraceTime and
docsBpiCmtsDefaultTEKGraceTime as obsolete objects, to prevent OID
reassignment. Several object descriptions were also corrected."

REVISION "200002161930Z"
DESCRIPTION
"Initial version.
CableLabs requires the implementation of this MIB in certified DOCSIS
1.0 cable modems implementing the Baseline Privacy Interface, per
DOCSIS 1.0 engineering change notice oss-n-99027."
::= { docsIfMib 5 }

docsBpiMIBObjects  OBJECT IDENTIFIER ::= { docsBpiMIB 1 }

-- Cable Modem Group

docsBpiCmObjects OBJECT IDENTIFIER ::= { docsBpiMIBObjects 1 }

--
-- The BPI base and authorization table for CMs, indexed by ifIndex
--

docsBpiCmBaseTable      OBJECT-TYPE
SYNTAX                  SEQUENCE OF     DocsBpiCmBaseEntry
MAX-ACCESS              not-accessible
STATUS                  current
DESCRIPTION
"This table describes the basic and authorization-related Baseline
Privacy attributes of each CM MAC interface."
::= { docsBpiCmObjects 1 }

docsBpiCmBaseEntry      OBJECT-TYPE
SYNTAX                  DocsBpiCmBaseEntry
MAX-ACCESS              not-accessible
STATUS                  current
DESCRIPTION
"Each entry contains objects describing attributes of one CM MAC
interface. An entry in this table exists for each ifEntry with an
ifType of docsCableMaclayer(127)."
INDEX                   { ifIndex }
::= { docsBpiCmBaseTable 1 }

DocsBpiCmBaseEntry ::= SEQUENCE {
docsBpiCmPrivacyEnable                  TruthValue,
docsBpiCmPublicKey                      OCTET STRING,
docsBpiCmAuthState                      INTEGER,
docsBpiCmAuthKeySequenceNumber          Integer32,
docsBpiCmAuthExpires                    DateAndTime,
docsBpiCmAuthReset                      TruthValue,
docsBpiCmAuthGraceTime                  Integer32,
docsBpiCmTEKGraceTime                   Integer32,
docsBpiCmAuthWaitTimeout                Integer32,
docsBpiCmReauthWaitTimeout              Integer32,
docsBpiCmOpWaitTimeout                  Integer32,
docsBpiCmRekeyWaitTimeout               Integer32,
docsBpiCmAuthRejectWaitTimeout          Integer32,
docsBpiCmAuthRequests                   Counter32,
docsBpiCmAuthReplies                    Counter32,
docsBpiCmAuthRejects                    Counter32,
docsBpiCmAuthInvalids                   Counter32,
docsBpiCmAuthRejectErrorCode            INTEGER,
docsBpiCmAuthRejectErrorString          DisplayString,
docsBpiCmAuthInvalidErrorCode           INTEGER,
docsBpiCmAuthInvalidErrorString         DisplayString
}

docsBpiCmPrivacyEnable  OBJECT-TYPE
SYNTAX                  TruthValue
MAX-ACCESS              read-only
STATUS                  current
DESCRIPTION
"This object identifies whether this CM is provisioned to run
Baseline Privacy. This is analogous to the presence (or absence)
of the Baseline Privacy Configuration Setting option. The status
of each individual SID with respect to Baseline Privacy is
captured in the docsBpiCmTEKPrivacyEnable object."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1."
::= { docsBpiCmBaseEntry 1 }

docsBpiCmPublicKey      OBJECT-TYPE
SYNTAX                  OCTET STRING (SIZE (74 | 106 | 140 | 270))
MAX-ACCESS              read-only
STATUS                  current
DESCRIPTION
"The value of this object is a DER-encoded RSAPublicKey ASN.1 type
string, as defined in the RSA Encryption Standard (PKCS #1) [22],
corresponding to the public key of the CM. The 74, 106, 140, and
270 byte key encoding lengths correspond to 512 bit, 768 bit, 1024
bit, and 2048 public moduli respectively."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.2.4."
::= { docsBpiCmBaseEntry 2 }

   docsBpiCmAuthState      OBJECT-TYPE 
   SYNTAX                  INTEGER {

                                   start(1),
                                   authWait(2),
                                   authorized(3),
                                   reauthWait(4),
                                   authRejectWait(5)

EID 334 (Verified) is as follows:

Section: 4

Original Text:

   docsBpiCmAuthState      OBJECT-TYPE
   SYNTAX                  INTEGER {
    
                                   authWait(2),
                                   authorized(3),
                                   reauthWait(4),
                                   authRejectWait(5)

Corrected Text:

   docsBpiCmAuthState      OBJECT-TYPE
   SYNTAX                  INTEGER {

                                   start(1),
                                   authWait(2),
                                   authorized(3),
                                   reauthWait(4),
                                   authRejectWait(5)
Notes:
2014-07-14: comma added. Thanks to Mark Ellison for the correction.
} MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the state of the CM authorization FSM. The start state indicates that FSM is in its initial state." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.1.2.1." ::= { docsBpiCmBaseEntry 3 } docsBpiCmAuthKeySequenceNumber OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the authorization key sequence number for this FSM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.2 and 4.2.2.10." ::= { docsBpiCmBaseEntry 4 } docsBpiCmAuthExpires OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time when the current authorization for this FSM expires. If the CM does not have an active authorization, then the value is of the expiration date and time of the last active authorization." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.2 and 4.2.2.9." ::= { docsBpiCmBaseEntry 5 } docsBpiCmAuthReset OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to TRUE generates a Reauthorize event in the authorization FSM. Reading this object always returns FALSE." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.1.2.3.4." ::= { docsBpiCmBaseEntry 6 } docsBpiCmAuthGraceTime OBJECT-TYPE SYNTAX Integer32 (1..1800) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the grace time for an authorization key. A CM is expected to start trying to get a new authorization key beginning AuthGraceTime seconds before the authorization key actually expires." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.3." ::= { docsBpiCmBaseEntry 7 } docsBpiCmTEKGraceTime OBJECT-TYPE SYNTAX Integer32 (1..1800) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the grace time for a TEK. A CM is expected to start trying to get a new TEK beginning TEKGraceTime seconds before the TEK actually expires." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.6." ::= { docsBpiCmBaseEntry 8 } docsBpiCmAuthWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..30) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Authorize Wait Timeout." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.1." ::= { docsBpiCmBaseEntry 9 } docsBpiCmReauthWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..30) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Reauthorize Wait Timeout in seconds." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.2." ::= { docsBpiCmBaseEntry 10 } docsBpiCmOpWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..10) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Operational Wait Timeout in seconds." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.4." ::= { docsBpiCmBaseEntry 11 } docsBpiCmRekeyWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..10) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Rekey Wait Timeout in seconds." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.5." ::= { docsBpiCmBaseEntry 12 } docsBpiCmAuthRejectWaitTimeout OBJECT-TYPE SYNTAX Integer32 (1..600) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Authorization Reject Wait Timeout in seconds." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.7." ::= { docsBpiCmBaseEntry 13 } docsBpiCmAuthRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CM has transmitted an Authorization Request message." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.1." ::= { docsBpiCmBaseEntry 14 } docsBpiCmAuthReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CM has received an Authorization Reply message." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.2." ::= { docsBpiCmBaseEntry 15 } docsBpiCmAuthRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CM has received an Authorization Reject message." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.3." ::= { docsBpiCmBaseEntry 16 } docsBpiCmAuthInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CM has received an Authorization Invalid message." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.7." ::= { docsBpiCmBaseEntry 17 } docsBpiCmAuthRejectErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedCm(3), unauthorizedSid(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent Authorization Reject message received by the CM. This has value unknown(2) if the last Error-Code value was 0, and none(1) if no Authorization Reject message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.3 and 4.2.2.16." ::= { docsBpiCmBaseEntry 18 } docsBpiCmAuthRejectErrorString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent Authorization Reject message received by the CM. This is a zero length string if no Authorization Reject message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.3 and 4.2.2.6." ::= { docsBpiCmBaseEntry 19 } docsBpiCmAuthInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedCm(3), unsolicited(5), invalidKeySequence(6), keyRequestAuthenticationFailure(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent Authorization Invalid message received by the CM. This has value unknown(2) if the last Error-Code value was 0, and none(1) if no Authorization Invalid message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.7 and 4.2.2.16." ::= { docsBpiCmBaseEntry 20 } docsBpiCmAuthInvalidErrorString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent Authorization Invalid message received by the CM. This is a zero length string if no Authorization Invalid message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.7 and 4.2.2.6." ::= { docsBpiCmBaseEntry 21 } -- -- The CM TEK Table, indexed by ifIndex and SID -- docsBpiCmTEKTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpiCmTEKEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the attributes of each CM Traffic Encryption Key (TEK) association. The CM maintains (no more than) one TEK association per SID per CM MAC interface." ::= { docsBpiCmObjects 2 } docsBpiCmTEKEntry OBJECT-TYPE SYNTAX DocsBpiCmTEKEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing the TEK association attributes of one SID. The CM MUST create one entry per unicast SID, regardless of whether the SID was obtained from a Registration Response message, or from an Authorization Reply message." INDEX { ifIndex, docsIfCmServiceId } ::= { docsBpiCmTEKTable 1 } DocsBpiCmTEKEntry ::= SEQUENCE { docsBpiCmTEKPrivacyEnable TruthValue, docsBpiCmTEKState INTEGER, docsBpiCmTEKExpiresOld DateAndTime, docsBpiCmTEKExpiresNew DateAndTime, docsBpiCmTEKKeyRequests Counter32, docsBpiCmTEKKeyReplies Counter32, docsBpiCmTEKKeyRejects Counter32, docsBpiCmTEKInvalids Counter32, docsBpiCmTEKAuthPends Counter32, docsBpiCmTEKKeyRejectErrorCode INTEGER, docsBpiCmTEKKeyRejectErrorString DisplayString, docsBpiCmTEKInvalidErrorCode INTEGER, docsBpiCmTEKInvalidErrorString DisplayString } docsBpiCmTEKPrivacyEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies whether this SID is provisioned to run Baseline Privacy. This is analogous to enabling Baseline Privacy on a provisioned SID using the Class-of-Service Privacy Enable option. Baseline Privacy is not effectively enabled for any SID unless Baseline Privacy is enabled for the CM, which is managed via the docsBpiCmPrivacyEnable object." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.1.2." ::= { docsBpiCmTEKEntry 1 } docsBpiCmTEKState OBJECT-TYPE SYNTAX INTEGER { start(1), opWait(2), opReauthWait(3), operational(4), rekeyWait(5), rekeyReauthWait(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the state of the indicated TEK FSM. The start(1) state indicates that FSM is in its initial state." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.1.3.1." ::= { docsBpiCmTEKEntry 2 } docsBpiCmTEKExpiresOld OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the immediate predecessor of the most recent TEK for this FSM. If this FSM has only one TEK, then the value is the time of activation of this FSM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.5 and 4.2.2.9." ::= { docsBpiCmTEKEntry 3 } docsBpiCmTEKExpiresNew OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the most recent TEK for this FSM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.5 and 4.2.2.9." ::= { docsBpiCmTEKEntry 4 } docsBpiCmTEKKeyRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CM has transmitted a Key Request message." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.4." ::= { docsBpiCmTEKEntry 5 } docsBpiCmTEKKeyReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CM has received a Key Reply message, including a message whose authentication failed." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.5." ::= { docsBpiCmTEKEntry 6 } docsBpiCmTEKKeyRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CM has received a Key Reject message, including a message whose authentication failed." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.6." ::= { docsBpiCmTEKEntry 7 } docsBpiCmTEKInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CM has received a TEK Invalid message, including a message whose authentication failed." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.8." ::= { docsBpiCmTEKEntry 8 } docsBpiCmTEKAuthPends OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times an Authorization Pending (Auth Pend) event occurred in this FSM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.1.3.3.3." ::= { docsBpiCmTEKEntry 9 } docsBpiCmTEKKeyRejectErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedSid(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent Key Reject message received by the CM. This has value unknown(2) if the last Error-Code value was 0, and none(1) if no Key Reject message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.1.2.6 and 4.2.2.16." ::= { docsBpiCmTEKEntry 10 } docsBpiCmTEKKeyRejectErrorString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent Key Reject message received by the CM. This is a zero length string if no Key Reject message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.1.2.6 and 4.2.2.6." ::= { docsBpiCmTEKEntry 11 } docsBpiCmTEKInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), invalidKeySequence(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent TEK Invalid message received by the CM. This has value unknown(2) if the last Error-Code value was 0, and none(1) if no TEK Invalid message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.1.2.8 and 4.2.2.16." ::= { docsBpiCmTEKEntry 12 } docsBpiCmTEKInvalidErrorString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent TEK Invalid message received by the CM. This is a zero length string if no TEK Invalid message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.1.2.8 and 4.2.2.6." ::= { docsBpiCmTEKEntry 13 } -- Cable Modem Termination System Group docsBpiCmtsObjects OBJECT IDENTIFIER ::= { docsBpiMIBObjects 2 } -- -- The BPI base table for CMTSs, indexed by ifIndex -- docsBpiCmtsBaseTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpiCmtsBaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the basic Baseline Privacy attributes of each CMTS MAC interface." ::= { docsBpiCmtsObjects 1 } docsBpiCmtsBaseEntry OBJECT-TYPE SYNTAX DocsBpiCmtsBaseEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing attributes of one CMTS MAC interface. An entry in this table exists for each ifEntry with an ifType of docsCableMaclayer(127)." INDEX { ifIndex } ::= { docsBpiCmtsBaseTable 1 } DocsBpiCmtsBaseEntry ::= SEQUENCE { docsBpiCmtsDefaultAuthLifetime Integer32, docsBpiCmtsDefaultTEKLifetime Integer32, docsBpiCmtsDefaultAuthGraceTime Integer32, docsBpiCmtsDefaultTEKGraceTime Integer32, docsBpiCmtsAuthRequests Counter32, docsBpiCmtsAuthReplies Counter32, docsBpiCmtsAuthRejects Counter32, docsBpiCmtsAuthInvalids Counter32 } docsBpiCmtsDefaultAuthLifetime OBJECT-TYPE SYNTAX Integer32 (1..6048000) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the default lifetime, in seconds, the CMTS assigns to a new authorization key." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.2." ::= { docsBpiCmtsBaseEntry 1 } docsBpiCmtsDefaultTEKLifetime OBJECT-TYPE SYNTAX Integer32 (1..604800) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the default lifetime, in seconds, the CMTS assigns to a new Traffic Encryption Key (TEK)." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.2." ::= { docsBpiCmtsBaseEntry 2 } -- Note: the following two objects have been obsoleted from this MIB. docsBpiCmtsDefaultAuthGraceTime OBJECT-TYPE SYNTAX Integer32 (1..1800) UNITS "seconds" MAX-ACCESS read-write STATUS obsolete DESCRIPTION "This object was obsoleted because the provisioning system, not the CMTS, manages the authorization key grace time for DOCSIS CMs." ::= { docsBpiCmtsBaseEntry 3 } docsBpiCmtsDefaultTEKGraceTime OBJECT-TYPE SYNTAX Integer32 (1..1800) UNITS "seconds" MAX-ACCESS read-write STATUS obsolete DESCRIPTION "This object was obsoleted because the provisioning system, not the CMTS, manages the Traffic Encryption Key (TEK) grace time for DOCSIS CMs." ::= { docsBpiCmtsBaseEntry 4 } docsBpiCmtsAuthRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has received an Authorization Request message from any CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.1." ::= { docsBpiCmtsBaseEntry 5 } docsBpiCmtsAuthReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has transmitted an Authorization Reply message to any CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.2." ::= { docsBpiCmtsBaseEntry 6 } docsBpiCmtsAuthRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has transmitted an Authorization Reject message to any CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.3." ::= { docsBpiCmtsBaseEntry 7 } docsBpiCmtsAuthInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has transmitted an Authorization Invalid message to any CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.7." ::= { docsBpiCmtsBaseEntry 8 } -- -- The CMTS Authorization Table, indexed by ifIndex and CM MAC address -- docsBpiCmtsAuthTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpiCmtsAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the attributes of each CM authorization association. The CMTS maintains one authorization association with each Baseline Privacy-enabled CM on each CMTS MAC interface." ::= { docsBpiCmtsObjects 2 } docsBpiCmtsAuthEntry OBJECT-TYPE SYNTAX DocsBpiCmtsAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing attributes of one authorization association. The CMTS MUST create one entry per CM per MAC interface, based on the receipt of an Authorization Request message, and MUST not delete the entry before the CM authorization permanently expires." INDEX { ifIndex, docsBpiCmtsAuthCmMacAddress } ::= { docsBpiCmtsAuthTable 1 } DocsBpiCmtsAuthEntry ::= SEQUENCE { docsBpiCmtsAuthCmMacAddress MacAddress, docsBpiCmtsAuthCmPublicKey OCTET STRING, docsBpiCmtsAuthCmKeySequenceNumber Integer32, docsBpiCmtsAuthCmExpires DateAndTime, docsBpiCmtsAuthCmLifetime Integer32, docsBpiCmtsAuthCmGraceTime Integer32, docsBpiCmtsAuthCmReset INTEGER, docsBpiCmtsAuthCmRequests Counter32, docsBpiCmtsAuthCmReplies Counter32, docsBpiCmtsAuthCmRejects Counter32, docsBpiCmtsAuthCmInvalids Counter32, docsBpiCmtsAuthRejectErrorCode INTEGER, docsBpiCmtsAuthRejectErrorString DisplayString, docsBpiCmtsAuthInvalidErrorCode INTEGER, docsBpiCmtsAuthInvalidErrorString DisplayString } docsBpiCmtsAuthCmMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object is the physical address of the CM to which the authorization association applies." ::= { docsBpiCmtsAuthEntry 1 } docsBpiCmtsAuthCmPublicKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0 | 74 | 106 | 140 | 270)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is a DER-encoded RSAPublicKey ASN.1 type string, as defined in the RSA Encryption Standard (PKCS #1) [22], corresponding to the public key of the CM. The 74, 106, 140, and 270 byte key encoding lengths correspond to 512 bit, 768 bit, 1024 bit, and 2048 public moduli respectively. This is a zero-length string if the CMTS does not retain the public key." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.2.4." ::= { docsBpiCmtsAuthEntry 2 } docsBpiCmtsAuthCmKeySequenceNumber OBJECT-TYPE SYNTAX Integer32 (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the authorization key sequence number for this CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.2 and 4.2.2.10." ::= { docsBpiCmtsAuthEntry 3 } docsBpiCmtsAuthCmExpires OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time when the current authorization for this CM expires. If this CM does not have an active authorization, then the value is of the expiration date and time of the last active authorization." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.2 and 4.2.2.9." ::= { docsBpiCmtsAuthEntry 4 } docsBpiCmtsAuthCmLifetime OBJECT-TYPE SYNTAX Integer32 (1..6048000) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the lifetime, in seconds, the CMTS assigns to an authorization key for this CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.2 and Appendix A.2." ::= { docsBpiCmtsAuthEntry 5 } docsBpiCmtsAuthCmGraceTime OBJECT-TYPE SYNTAX Integer32 (1..1800) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the grace time for the authorization key in seconds. The CM is expected to start trying to get a new authorization key beginning AuthGraceTime seconds before the authorization key actually expires." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.3." ::= { docsBpiCmtsAuthEntry 6 } docsBpiCmtsAuthCmReset OBJECT-TYPE SYNTAX INTEGER { noResetRequested(1), invalidateAuth(2), sendAuthInvalid(3), invalidateTeks(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to invalidateAuth(2) causes the CMTS to invalidate the current CM authorization key, but not to transmit an Authorization Invalid message nor to invalidate unicast TEKs. Setting this object to sendAuthInvalid(3) causes the CMTS to invalidate the current CM authorization key, and to transmit an Authorization Invalid message to the CM, but not to invalidate unicast TEKs. Setting this object to invalidateTeks(4) causes the CMTS to invalidate the current CM authorization key, to transmit an Authorization Invalid message to the CM, and to invalidate all unicast TEKs associated with this CM authorization. Reading this object returns the most-recently-set value of this object, or returns noResetRequested(1) if the object has not been set since the last CMTS reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.1.2.3.4, 4.1.2.3.5, and 4.1.3.3.5." ::= { docsBpiCmtsAuthEntry 7 } docsBpiCmtsAuthCmRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has received an Authorization Request message from this CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.1." ::= { docsBpiCmtsAuthEntry 8 } docsBpiCmtsAuthCmReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has transmitted an Authorization Reply message to this CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.2." ::= { docsBpiCmtsAuthEntry 9 } docsBpiCmtsAuthCmRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has transmitted an Authorization Reject message to this CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.3." ::= { docsBpiCmtsAuthEntry 10 } docsBpiCmtsAuthCmInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has transmitted an Authorization Invalid message to this CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.7." ::= { docsBpiCmtsAuthEntry 11 } docsBpiCmtsAuthRejectErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedCm(3), unauthorizedSid(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent Authorization Reject message transmitted to the CM. This has value unknown(2) if the last Error-Code value was 0, and none(1) if no Authorization Reject message has been transmitted to the CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.3 and 4.2.2.16." ::= { docsBpiCmtsAuthEntry 12 } docsBpiCmtsAuthRejectErrorString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent Authorization Reject message transmitted to the CM. This is a zero length string if no Authorization Reject message has been transmitted to the CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.3 and 4.2.2.6." ::= { docsBpiCmtsAuthEntry 13 } docsBpiCmtsAuthInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedCm(3), unsolicited(5), invalidKeySequence(6), keyRequestAuthenticationFailure(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in most recent Authorization Invalid message transmitted to the CM. This has value unknown(2) if the last Error-Code value was 0, and none(1) if no Authorization Invalid message has been transmitted to the CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.7 and 4.2.2.16." ::= { docsBpiCmtsAuthEntry 14 } docsBpiCmtsAuthInvalidErrorString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in most recent Authorization Invalid message transmitted to the CM. This is a zero length string if no Authorization Invalid message has been transmitted to the CM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.7 and 4.2.2.6." ::= { docsBpiCmtsAuthEntry 15 } -- -- The CMTS TEK Table, indexed by ifIndex and SID -- docsBpiCmtsTEKTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpiCmtsTEKEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the attributes of each CM Traffic Encryption Key (TEK) association. The CMTS maintains one TEK association per BPI SID on each CMTS MAC interface." ::= { docsBpiCmtsObjects 3 } docsBpiCmtsTEKEntry OBJECT-TYPE SYNTAX DocsBpiCmtsTEKEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing attributes of one TEK association on a particular CMTS MAC interface. The CMTS MUST create one entry per SID per MAC interface, based on the receipt of an Key Request message, and MUST not delete the entry before the CM authorization for the SID permanently expires." INDEX { ifIndex, docsIfCmtsServiceId } ::= { docsBpiCmtsTEKTable 1 } DocsBpiCmtsTEKEntry ::= SEQUENCE { docsBpiCmtsTEKLifetime Integer32, docsBpiCmtsTEKGraceTime Integer32, docsBpiCmtsTEKExpiresOld DateAndTime, docsBpiCmtsTEKExpiresNew DateAndTime, docsBpiCmtsTEKReset TruthValue, docsBpiCmtsKeyRequests Counter32, docsBpiCmtsKeyReplies Counter32, docsBpiCmtsKeyRejects Counter32, docsBpiCmtsTEKInvalids Counter32, docsBpiCmtsKeyRejectErrorCode INTEGER, docsBpiCmtsKeyRejectErrorString DisplayString, docsBpiCmtsTEKInvalidErrorCode INTEGER, docsBpiCmtsTEKInvalidErrorString DisplayString } docsBpiCmtsTEKLifetime OBJECT-TYPE SYNTAX Integer32 (1..604800) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object is the lifetime, in seconds, the CMTS assigns to keys for this TEK association." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.5 and Appendix A.2." ::= { docsBpiCmtsTEKEntry 1 } docsBpiCmtsTEKGraceTime OBJECT-TYPE SYNTAX Integer32 (1..1800) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the grace time for the TEK in seconds. The CM is expected to start trying to get a new TEK beginning TEKGraceTime seconds before the TEK actually expires." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.6." ::= { docsBpiCmtsTEKEntry 2 } docsBpiCmtsTEKExpiresOld OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the immediate predecessor of the most recent TEK for this FSM. If this FSM has only one TEK, then the value is the time of activation of this FSM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.5 and 4.2.2.9." ::= { docsBpiCmtsTEKEntry 3 } docsBpiCmtsTEKExpiresNew OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the actual clock time for expiration of the most recent TEK for this FSM." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.5 and 4.2.2.9." ::= { docsBpiCmtsTEKEntry 4 } docsBpiCmtsTEKReset OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to TRUE causes the CMTS to invalidate the current active TEK(s) (plural due to key transition periods), and to generate a new TEK for the associated SID; the CMTS MAY also generate an unsolicited TEK Invalid message, to optimize the TEK synchronization between the CMTS and the CM. Reading this object always returns FALSE." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.1.3.3.5." ::= { docsBpiCmtsTEKEntry 5 } docsBpiCmtsKeyRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has received a Key Request message." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.4." ::= { docsBpiCmtsTEKEntry 6 } docsBpiCmtsKeyReplies OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has transmitted a Key Reply message." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.5." ::= { docsBpiCmtsTEKEntry 7 } docsBpiCmtsKeyRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has transmitted a Key Reject message." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.6." ::= { docsBpiCmtsTEKEntry 8 } docsBpiCmtsTEKInvalids OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the count of times the CMTS has transmitted a TEK Invalid message." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.8." ::= { docsBpiCmtsTEKEntry 9 } docsBpiCmtsKeyRejectErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), unauthorizedSid(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent Key Reject message sent in response to a Key Request for this BPI SID. This has value unknown(2) if the last Error-Code value was 0, and none(1) if no Key Reject message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.6 and 4.2.2.16." ::= { docsBpiCmtsTEKEntry 10 } docsBpiCmtsKeyRejectErrorString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in the most recent Key Reject message sent in response to a Key Request for this BPI SID. This is a zero length string if no Key Reject message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.6 and 4.2.2.6." ::= { docsBpiCmtsTEKEntry 11 } docsBpiCmtsTEKInvalidErrorCode OBJECT-TYPE SYNTAX INTEGER { none(1), unknown(2), invalidKeySequence(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the enumerated description of the Error-Code in the most recent TEK Invalid message sent in association with this BPI SID. This has value unknown(2) if the last Error-Code value was 0, and none(1) if no TEK Invalid message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.8 and 4.2.2.16." ::= { docsBpiCmtsTEKEntry 12 } docsBpiCmtsTEKInvalidErrorString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the Display-String in the most recent TEK Invalid message sent in association with this BPI SID. This is a zero length string if no TEK Invalid message has been received since reboot." REFERENCE "DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.8 and 4.2.2.6." ::= { docsBpiCmtsTEKEntry 13 } -- -- The CMTS Multicast Control Group -- docsBpiMulticastControl OBJECT IDENTIFIER ::= { docsBpiCmtsObjects 4 } -- -- The CMTS IP Multicast Mapping Table, indexed by IP multicast -- address and prefix, and by ifindex -- docsBpiIpMulticastMapTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpiIpMulticastMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the mapping of IP multicast address prefixes to multicast SIDs on each CMTS MAC interface." ::= { docsBpiMulticastControl 1 } docsBpiIpMulticastMapEntry OBJECT-TYPE SYNTAX DocsBpiIpMulticastMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing the mapping of one IP multicast address prefix to one multicast SID on one CMTS MAC interface. The CMTS uses the mapping when forwarding downstream IP multicast traffic." INDEX { ifIndex, docsBpiIpMulticastAddress, docsBpiIpMulticastPrefixLength } ::= { docsBpiIpMulticastMapTable 1 } DocsBpiIpMulticastMapEntry ::= SEQUENCE { docsBpiIpMulticastAddress IpAddress, docsBpiIpMulticastPrefixLength Integer32, docsBpiIpMulticastServiceId Integer32, docsBpiIpMulticastMapControl RowStatus } docsBpiIpMulticastAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the IP multicast address (prefix) to be mapped by this row, in conjunction with docsBpiIpMulticastPrefixLength." ::= { docsBpiIpMulticastMapEntry 1 } docsBpiIpMulticastPrefixLength OBJECT-TYPE SYNTAX Integer32 (0..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the IP multicast address prefix length for this row. The value of this object represents the length in bits of docsBpiIpMulticastAddress for multicast address comparisons, using big-endian ordering. An IP multicast address matches this row if the (docsBpiIpMulticastPrefixLength) most significant bits of the IP multicast address and of the (docsBpiIpMulticastAddress) are identical. This object is similar in usage to an IP address mask. The value 0 corresponds to IP address mask 0.0.0.0, the value 1 corresponds to IP address mask 128.0.0.0, the value 8 corresponds to IP address mask 255.0.0.0, and the value 32 corresponds to IP address mask 255.255.255.255." ::= { docsBpiIpMulticastMapEntry 2 } docsBpiIpMulticastServiceId OBJECT-TYPE SYNTAX Integer32 (8192..16368) MAX-ACCESS read-create STATUS current DESCRIPTION "This object represents the multicast SID to be used in this IP multicast address prefix mapping entry." -- DEFVAL is an unused multicast SID value chosen by CMTS. ::= { docsBpiIpMulticastMapEntry 3 } docsBpiIpMulticastMapControl OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object controls and reflects the IP multicast address prefix mapping entry. There is no restriction on the ability to change values in this row while the row is active." ::= { docsBpiIpMulticastMapEntry 4 } -- -- The CMTS Multicast SID Authorization Table, indexed by ifIndex by -- multicast SID by CM MAC address -- docsBpiMulticastAuthTable OBJECT-TYPE SYNTAX SEQUENCE OF DocsBpiMulticastAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the multicast SID authorization for each CM on each CMTS MAC interface." ::= { docsBpiMulticastControl 2 } docsBpiMulticastAuthEntry OBJECT-TYPE SYNTAX DocsBpiMulticastAuthEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains objects describing the key authorization of one cable modem for one multicast SID for one CMTS MAC interface." INDEX { ifIndex, docsBpiMulticastServiceId, docsBpiMulticastCmMacAddress } ::= { docsBpiMulticastAuthTable 1 } DocsBpiMulticastAuthEntry ::= SEQUENCE { docsBpiMulticastServiceId Integer32, docsBpiMulticastCmMacAddress MacAddress, docsBpiMulticastAuthControl RowStatus } docsBpiMulticastServiceId OBJECT-TYPE SYNTAX Integer32 (8192..16368) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the multicast SID for authorization." ::= { docsBpiMulticastAuthEntry 1 } docsBpiMulticastCmMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the MAC address of the CM to which the multicast SID authorization applies." ::= { docsBpiMulticastAuthEntry 2 } docsBpiMulticastAuthControl OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object controls and reflects the CM authorization for each multicast SID. There is no restriction on the ability to change values in this row while the row is active." ::= { docsBpiMulticastAuthEntry 3 } -- -- The BPI MIB Conformance Statements (with a placeholder for -- notifications) -- docsBpiNotification OBJECT IDENTIFIER ::= { docsBpiMIB 2 } docsBpiConformance OBJECT IDENTIFIER ::= { docsBpiMIB 3 } docsBpiCompliances OBJECT IDENTIFIER ::= { docsBpiConformance 1 } docsBpiGroups OBJECT IDENTIFIER ::= { docsBpiConformance 2 } docsBpiBasicCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "This is the compliance statement for devices which implement the DOCSIS Baseline Privacy Interface." MODULE -- docsBpiMIB -- conditionally mandatory group GROUP docsBpiCmGroup DESCRIPTION "This group is implemented only in CMs, not in CMTSs." -- conditionally mandatory group GROUP docsBpiCmtsGroup DESCRIPTION "This group is implemented only in CMTSs, not in CMs." -- relaxation on mandatory range (unnecessary since object is read-only) -- OBJECT docsBpiCmAuthGraceTime -- SYNTAX Integer32 (300..1800) -- DESCRIPTION -- "The refined range corresponds to the minimum and maximum values in -- operational networks, according to Appendix A.2 in [18]." -- relaxation on mandatory range (unnecessary since object is read-only) -- OBJECT docsBpiCmTEKGraceTime -- SYNTAX Integer32 (300..1800) -- DESCRIPTION -- "The refined range corresponds to the minimum and maximum values in -- operational networks, according to Appendix A.2 in [18]." -- relaxation on mandatory range OBJECT docsBpiCmtsDefaultAuthLifetime SYNTAX Integer32 (86400..6048000) DESCRIPTION "The refined range corresponds to the minimum and maximum values in operational networks, according to Appendix A.2 in [18]." -- relaxation on mandatory range OBJECT docsBpiCmtsDefaultTEKLifetime SYNTAX Integer32 (1800..604800) DESCRIPTION "The refined range corresponds to the minimum and maximum values in operational networks, according to Appendix A.2 in [18]." -- relaxation on mandatory range (object removed from MIB) -- OBJECT docsBpiCmtsDefaultAuthGraceTime -- SYNTAX INTEGER (300..1800) -- DESCRIPTION -- "The refined range corresponds to the minimum and maximum values in -- operational networks, according to Appendix A.2 in [18]." -- relaxation on mandatory range (object removed from MIB) -- OBJECT docsBpiCmtsDefaultTEKGraceTime -- SYNTAX INTEGER (300..1800) -- DESCRIPTION -- "The refined range corresponds to the minimum and maximum values in -- operational networks, according to Appendix A.2 in [18]." -- relaxation on mandatory range OBJECT docsBpiCmtsAuthCmLifetime SYNTAX Integer32 (86400..6048000) DESCRIPTION "The refined range corresponds to the minimum and maximum values in operational networks, according to Appendix A.2 in [18]." -- relaxation on mandatory range (unnecessary since object is read-only) -- OBJECT docsBpiCmtsAuthCmGraceTime -- SYNTAX Integer32 (300..1800) -- DESCRIPTION -- "The refined range corresponds to the minimum and maximum values in -- operational networks, according to Appendix A.2 in [18]." -- relaxation on mandatory range OBJECT docsBpiCmtsTEKLifetime SYNTAX Integer32 (1800..604800) DESCRIPTION "The refined range corresponds to the minimum and maximum values in operational networks, according to Appendix A.2 in [18]." -- relaxation on mandatory range (unnecessary since object is read-only) -- OBJECT docsBpiCmtsTEKGraceTime -- SYNTAX Integer32 (300..1800) -- DESCRIPTION -- "The refined range corresponds to the minimum and maximum values in -- operational networks, according to Appendix A.2 in [18]." ::= { docsBpiCompliances 1 } docsBpiCmGroup OBJECT-GROUP OBJECTS { docsBpiCmPrivacyEnable, docsBpiCmPublicKey, docsBpiCmAuthState, docsBpiCmAuthKeySequenceNumber, docsBpiCmAuthExpires, docsBpiCmAuthReset, docsBpiCmAuthGraceTime, docsBpiCmTEKGraceTime, docsBpiCmAuthWaitTimeout, docsBpiCmReauthWaitTimeout, docsBpiCmOpWaitTimeout, docsBpiCmRekeyWaitTimeout, docsBpiCmAuthRejectWaitTimeout, docsBpiCmAuthRequests, docsBpiCmAuthReplies, docsBpiCmAuthRejects, docsBpiCmAuthInvalids, docsBpiCmAuthRejectErrorCode, docsBpiCmAuthRejectErrorString, docsBpiCmAuthInvalidErrorCode, docsBpiCmAuthInvalidErrorString, docsBpiCmTEKPrivacyEnable, docsBpiCmTEKState, docsBpiCmTEKExpiresOld, docsBpiCmTEKExpiresNew, docsBpiCmTEKKeyRequests, docsBpiCmTEKKeyReplies, docsBpiCmTEKKeyRejects, docsBpiCmTEKInvalids, docsBpiCmTEKAuthPends, docsBpiCmTEKKeyRejectErrorCode, docsBpiCmTEKKeyRejectErrorString, docsBpiCmTEKInvalidErrorCode, docsBpiCmTEKInvalidErrorString } STATUS current DESCRIPTION "This collection of objects provides CM BPI status and control." ::= { docsBpiGroups 1 } docsBpiCmtsGroup OBJECT-GROUP OBJECTS { docsBpiCmtsDefaultAuthLifetime, docsBpiCmtsDefaultTEKLifetime, docsBpiCmtsAuthRequests, docsBpiCmtsAuthReplies, docsBpiCmtsAuthRejects, docsBpiCmtsAuthInvalids, docsBpiCmtsAuthCmPublicKey, docsBpiCmtsAuthCmKeySequenceNumber, docsBpiCmtsAuthCmExpires, docsBpiCmtsAuthCmLifetime, docsBpiCmtsAuthCmGraceTime, docsBpiCmtsAuthCmReset, docsBpiCmtsAuthCmRequests, docsBpiCmtsAuthCmReplies, docsBpiCmtsAuthCmRejects, docsBpiCmtsAuthCmInvalids, docsBpiCmtsAuthRejectErrorCode, docsBpiCmtsAuthRejectErrorString, docsBpiCmtsAuthInvalidErrorCode, docsBpiCmtsAuthInvalidErrorString, docsBpiCmtsTEKLifetime, docsBpiCmtsTEKGraceTime, docsBpiCmtsTEKExpiresOld, docsBpiCmtsTEKExpiresNew, docsBpiCmtsTEKReset, docsBpiCmtsKeyRequests, docsBpiCmtsKeyReplies, docsBpiCmtsKeyRejects, docsBpiCmtsTEKInvalids, docsBpiCmtsKeyRejectErrorCode, docsBpiCmtsKeyRejectErrorString, docsBpiCmtsTEKInvalidErrorCode, docsBpiCmtsTEKInvalidErrorString, docsBpiIpMulticastServiceId, docsBpiIpMulticastMapControl, docsBpiMulticastAuthControl } STATUS current DESCRIPTION "This collection of objects provides CMTS BPI status and control." ::= { docsBpiGroups 2 } docsBpiObsoleteObjectsGroup OBJECT-GROUP OBJECTS { docsBpiCmtsDefaultAuthGraceTime, docsBpiCmtsDefaultTEKGraceTime } STATUS obsolete DESCRIPTION "This is a collection of obsolete BPI objects." ::= { docsBpiGroups 3 } END 5. Acknowledgments This document was produced by the IPCDN Working Group. Much of the content of this MIB was conceived by Chet Birger and Mike StJohns. Kazuyoshi Ozawa and Bob Himlin provided many useful technical corrections. 6. References [1] Harrington, D., Presuhn, R. and B. Wijnen, "An Architecture for Describing SNMP Management Frameworks", RFC 2571, April 1999. [2] Rose, M. and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based Internets", STD 16, RFC 1155, May 1990. [3] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD 16, RFC 1212, March 1991. [4] Rose, M., "A Convention for Defining Traps for use with the SNMP", RFC 1215, March 1991. [5] McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Structure of e Management Information for Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [6] McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [7] McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [8] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple Network Management Protocol", STD 15, RFC 1157, May 1990. [9] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901, January 1996. [10] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1906, January 1996. [11] Case, J., Harrington D., Presuhn R. and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2572, April 1999. [12] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2574, April 1999. [13] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996. [14] Levi, D., Meyer, P. and B. Stewart, "SNMP Applications", RFC 2573, April 1999. [15] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2575, April 1999. [16] St. Johns, M., editor, "Radio Frequency (RF) Interface Management Information Base for MCNS/DOCSIS compliant RF interfaces", RFC 2670, August 1999. [17] St. Johns, M., editor, "DOCSIS Cable Device MIB, Cable Device Management Information Base for DOCSIS compliant Cable Modems and Cable Modem Termination Systems", RFC 2669, August 1999. [18] "Data-Over-Cable Service Interface Specifications: Baseline Privacy Interface Specification SP-BPI-I02-990319", DOCSIS, March 1999, http://www.cablemodem.com/. [19] "Data-Over-Cable Service Interface Specifications: Cable Modem Radio Frequency Interface Specification SP-RFI-I05-991105", DOCSIS, November 1999, http://www.cablemodem.com/. [20] "Data-Over-Cable Service Interface Specifications: Operations Support System Interface Specification RF Interface SP-OSSI-RF- I02-990113", DOCSIS, January 1999, http://www.cablemodem.com/. [21] "Data-Over-Cable Service Interface Specifications: Baseline Privacy Plus Interface Specification SP-BPI+-I05-000714", DOCSIS, July 2000, http://www.cablemodem.com/. [22] RSA Laboratories, "The Public-Key Cryptography Standards", RSA Data Security Inc., Redwood City, CA. [23] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [24] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction to Version 3 of the Internet-standard Network Management Framework", RFC 2570, April 1999. 7. Security Considerations The Baseline Privacy Interface provides data encryption for DOCSIS data-over-cable services. Baseline Privacy-capable cable modems have RSA private/public key pairs installed by manufacturers. The public key is used to encrypt an Authorization key, and the Authorization key is used to encrypt one or more Traffic Encryption Keys (TEKs). The TEKs are used to encrypt both upstream and downstream data traffic. Please refer to [18] to obtain further information on the Baseline Privacy specification. In particular, the Baseline Privacy Interface does not provide an authentication service. CMTS implementors are encouraged not to rely on the MAC address of the CM for service authorization -- in particular, for the docsBpiMulticastAuthTable in this MIB. The Baseline Privacy Plus Interface does provide a CM authentication service, and the working group expects to issue a MIB for the management of BPI+ at a later time. This MIB specification contains a number of read-write objects, that should be protected from unauthorized modification to prevent denial of service and theft of service attacks: in particular, objects that reset state machines (ex. docsBpiCmAuthReset), change key lifetimes (ex. docsBpiCmtsDefaultAuthLifetime), change rekeying grace times (ex. docsBpiCmtsDefaultAuthGraceTime), and control multicast traffic (ex. most objects in the docsBpiMulticastControl group). The desired means to protect these objects from unwarranted access is to implement the security features as provided by the SNMPv3 framework. Specifically, the use of the User-based Security Model [12] and the View-based Access Control Model [15] is recommended. Weaker methods to protect CMs from unauthorized access include using the docsDevNmAccessTable from the Cable Device MIB [17] to disallow configuration changes from unauthorized network management stations, and using the SNMP MIB Object and SNMP Write-Access Control configuration file options from the Radio Frequency Interface [19] to set MIB object values and disable SNMP SET operations at cable modem boot time. Note that these mechanisms may be vulnerable to an unauthorized network management station "spoofing" the source address of a legitimate network management station. 8. Intellectual Property The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director. 9. Author's Address Richard Woundy Cisco Systems 250 Apollo Drive Chelmsford, MA 01824 U.S.A. Phone: +1 978 244 8000 EMail: rwoundy@cisco.com 10. Full Copyright Statement Copyright (C) The Internet Society (2001). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Acknowledgement Funding for the RFC Editor function is currently provided by the Internet Society.