Internet Engineering Task Force (IETF)                        J. Halpern
Request for Comments: 5812                                          Self
Category: Standards Track                                  J. Hadi Salim
ISSN: 2070-1721                                            Znyx Networks
                                                              March 2010


           Forwarding and Control Element Separation (ForCES)
                        Forwarding Element Model

Abstract

   This document defines the forwarding element (FE) model used in the
   Forwarding and Control Element Separation (ForCES) protocol.  The
   model represents the capabilities, state, and configuration of
   forwarding elements within the context of the ForCES protocol, so
   that control elements (CEs) can control the FEs accordingly.  More
   specifically, the model describes the logical functions that are
   present in an FE, what capabilities these functions support, and how
   these functions are or can be interconnected.  This FE model is
   intended to satisfy the model requirements specified in RFC 3654.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc5812.
















Halpern & Hadi Salim         Standards Track                    [Page 1]


RFC 5812                     ForCES FE Model                  March 2010


Copyright Notice

   Copyright (c) 2010 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.





































Halpern & Hadi Salim         Standards Track                    [Page 2]


RFC 5812                     ForCES FE Model                  March 2010


Table of Contents

   1. Introduction ....................................................5
      1.1. Requirements on the FE Model ...............................5
      1.2. The FE Model in Relation to FE Implementations .............6
      1.3. The FE Model in Relation to the ForCES Protocol ............6
      1.4. Modeling Language for the FE Model .........................7
      1.5. Document Structure .........................................8
   2. Definitions .....................................................8
   3. ForCES Model Concepts ..........................................10
      3.1. ForCES Capability Model and State Model ...................12
           3.1.1. FE Capability Model and State Model ................12
           3.1.2. Relating LFB and FE Capability and State Model .....14
      3.2. Logical Functional Block (LFB) Modeling ...................14
           3.2.1. LFB Outputs ........................................18
           3.2.2. LFB Inputs .........................................21
           3.2.3. Packet Type ........................................24
           3.2.4. Metadata ...........................................24
           3.2.5. LFB Events .........................................27
           3.2.6. Component Properties ...............................28
           3.2.7. LFB Versioning .....................................29
           3.2.8. LFB Inheritance ....................................29
      3.3. ForCES Model Addressing ...................................30
           3.3.1. Addressing LFB Components: Paths and Keys ..........32
      3.4. FE Data Path Modeling .....................................32
           3.4.1. Alternative Approaches for Modeling FE Data Paths ..33
           3.4.2. Configuring the LFB Topology .......................37
   4. Model and Schema for LFB Classes ...............................41
      4.1. Namespace .................................................42
      4.2. <LFBLibrary> Element ......................................42
      4.3. <load> Element ............................................44
      4.4. <frameDefs> Element for Frame Type Declarations ...........45
      4.5. <dataTypeDefs> Element for Data Type Definitions ..........45
           4.5.1. <typeRef> Element for Renaming Existing
                  Data Types .........................................49
           4.5.2. <atomic> Element for Deriving New Atomic Types .....49
           4.5.3. <array> Element to Define Arrays ...................50
           4.5.4. <struct> Element to Define Structures ..............54
           4.5.5. <union> Element to Define Union Types ..............56
           4.5.6. <alias> Element ....................................56
           4.5.7. Augmentations ......................................57
      4.6. <metadataDefs> Element for Metadata Definitions ...........58
      4.7. <LFBClassDefs> Element for LFB Class Definitions ..........59
           4.7.1. <derivedFrom> Element to Express LFB Inheritance ...62
           4.7.2. <inputPorts> Element to Define LFB Inputs ..........62
           4.7.3. <outputPorts> Element to Define LFB Outputs ........65
           4.7.4. <components> Element to Define LFB
                  Operational Components .............................67



Halpern & Hadi Salim         Standards Track                    [Page 3]


RFC 5812                     ForCES FE Model                  March 2010


           4.7.5. <capabilities> Element to Define LFB
                  Capability Components ..............................70
           4.7.6. <events> Element for LFB Notification Generation ...71
           4.7.7. <description> Element for LFB Operational
                  Specification ......................................79
      4.8. Properties ................................................79
           4.8.1. Basic Properties ...................................79
           4.8.2. Array Properties ...................................81
           4.8.3. String Properties ..................................81
           4.8.4. Octetstring Properties .............................82
           4.8.5. Event Properties ...................................83
           4.8.6. Alias Properties ...................................87
      4.9. XML Schema for LFB Class Library Documents ................88
   5. FE Components and Capabilities .................................99
      5.1. XML for FEObject Class Definition .........................99
      5.2. FE Capabilities ..........................................106
           5.2.1. ModifiableLFBTopology .............................106
           5.2.2. SupportedLFBs and SupportedLFBType ................106
      5.3. FE Components ............................................110
           5.3.1. FEState ...........................................110
           5.3.2. LFBSelectors and LFBSelectorType ..................110
           5.3.3. LFBTopology and LFBLinkType .......................110
           5.3.4. FENeighbors and FEConfiguredNeighborType ..........111
   6. Satisfying the Requirements on the FE Model ...................111
   7. Using the FE Model in the ForCES Protocol .....................112
      7.1. FE Topology Query ........................................115
      7.2. FE Capability Declarations ...............................116
      7.3. LFB Topology and Topology Configurability Query ..........116
      7.4. LFB Capability Declarations ..............................116
      7.5. State Query of LFB Components ............................118
      7.6. LFB Component Manipulation ...............................118
      7.7. LFB Topology Reconfiguration .............................118
   8. Example LFB Definition ........................................119
      8.1. Data Handling ............................................126
           8.1.1. Setting Up a DLCI .................................127
           8.1.2. Error Handling ....................................127
      8.2. LFB Components ...........................................128
      8.3. Capabilities .............................................128
      8.4. Events ...................................................129
   9. IANA Considerations ...........................................130
      9.1. URN Namespace Registration ...............................130
      9.2. LFB Class Names and LFB Class Identifiers ................130
   10. Authors Emeritus .............................................132
   11. Acknowledgments ..............................................132
   12. Security Considerations ......................................132
   13. References ...................................................132
      13.1. Normative References ....................................132
      13.2. Informative References ..................................133



Halpern & Hadi Salim         Standards Track                    [Page 4]


RFC 5812                     ForCES FE Model                  March 2010


1.  Introduction

   RFC 3746 [RFC3746] specifies a framework by which control elements
   (CEs) can configure and manage one or more separate forwarding
   elements (FEs) within a network element (NE) using the ForCES
   protocol.  The ForCES architecture allows forwarding elements of
   varying functionality to participate in a ForCES network element.
   The implication of this varying functionality is that CEs can make
   only minimal assumptions about the functionality provided by FEs in
   an NE.  Before CEs can configure and control the forwarding behavior
   of FEs, CEs need to query and discover the capabilities and states of
   their FEs.  RFC 3654 [RFC3654] mandates that the capabilities, states
   and configuration information be expressed in the form of an FE
   model.

   RFC 3444 [RFC3444] observed that information models (IMs) and data
   models (DMs) are different because they serve different purposes.
   "The main purpose of an IM is to model managed objects at a
   conceptual level, independent of any specific implementations or
   protocols used".  "DMs, conversely, are defined at a lower level of
   abstraction and include many details.  They are intended for
   implementors and include protocol-specific constructs".  Sometimes it
   is difficult to draw a clear line between the two.  The FE model
   described in this document is primarily an information model, but
   also includes some aspects of a data model, such as explicit
   definitions of the LFB (Logical Functional Block) class schema and FE
   schema.  It is expected that this FE model will be used as the basis
   to define the payload for information exchange between the CE and FE
   in the ForCES protocol.

1.1.  Requirements on the FE Model

   RFC 3654 [RFC3654] defines requirements that must be satisfied by a
   ForCES FE model.  To summarize, an FE model must define:

   o  Logically separable and distinct packet forwarding operations in
      an FE data path (Logical Functional Blocks or LFBs);

   o  The possible topological relationships (and hence the sequence of
      packet forwarding operations) between the various LFBs;

   o  The possible operational capabilities (e.g., capacity limits,
      constraints, optional features, granularity of configuration) of
      each type of LFB;

   o  The possible configurable parameters (e.g., components) of each
      type of LFB; and




Halpern & Hadi Salim         Standards Track                    [Page 5]


RFC 5812                     ForCES FE Model                  March 2010


   o  Metadata that may be exchanged between LFBs.

1.2.  The FE Model in Relation to FE Implementations

   The FE model proposed here is based on an abstraction using distinct
   Logical Functional Blocks (LFBs), which are interconnected in a
   directed graph, and receive, process, modify, and transmit packets
   along with metadata.  The FE model is designed, and any defined LFB
   classes should be designed, such that different implementations of
   the forwarding data path can be logically mapped onto the model with
   the functionality and sequence of operations correctly captured.
   However, the model is not intended to directly address how a
   particular implementation maps to an LFB topology.  It is left to the
   forwarding plane vendors to define how the FE functionality is
   represented using the FE model.  Our goal is to design the FE model
   such that it is flexible enough to accommodate most common
   implementations.

   The LFB topology model for a particular data path implementation must
   correctly capture the sequence of operations on the packet.  Metadata
   generation by certain LFBs MUST always precede any use of that
   metadata by subsequent LFBs in the topology graph; this is required
   for logically consistent operation.  Further, modification of packet
   fields that are subsequently used as inputs for further processing
   MUST occur in the order specified in the model for that particular
   implementation to ensure correctness.

1.3.  The FE Model in Relation to the ForCES Protocol

   The ForCES base protocol [RFC5810] is used by the CEs and FEs to
   maintain the communication channel between the CEs and FEs.  The
   ForCES protocol may be used to query and discover the intra-FE
   topology.  The details of a particular data path implementation
   inside an FE, including the LFB topology, along with the operational
   capabilities and attributes of each individual LFB, are conveyed to
   the CE within information elements in the ForCES protocol.  The model
   of an LFB class should define all of the information that needs to be
   exchanged between an FE and a CE for the proper configuration and
   management of that LFB.

   Specifying the various payloads of the ForCES messages in a
   systematic fashion is difficult without a formal definition of the
   objects being configured and managed (the FE and the LFBs within).
   The FE model document defines a set of classes and components for
   describing and manipulating the state of the LFBs within an FE.
   These class definitions themselves will generally not appear in the





Halpern & Hadi Salim         Standards Track                    [Page 6]


RFC 5812                     ForCES FE Model                  March 2010


   ForCES protocol.  Rather, ForCES protocol operations will reference
   classes defined in this model, including relevant components and the
   defined operations.

   Section 7 provides more detailed discussion on how the FE model
   should be used by the ForCES protocol.

1.4.  Modeling Language for the FE Model

   Even though not absolutely required, it is beneficial to use a formal
   data modeling language to represent the conceptual FE model described
   in this document.  Use of a formal language can help to enforce
   consistency and logical compatibility among LFBs.  A full
   specification will be written using such a data modeling language.
   The formal definition of the LFB classes may facilitate the eventual
   automation of some of the code generation process and the functional
   validation of arbitrary LFB topologies.  These class definitions form
   the LFB library.  Documents that describe LFB classes are therefore
   referred to as LFB library documents.

   Human readability was the most important factor considered when
   selecting the specification language, whereas encoding, decoding, and
   transmission performance were not a selection factor.  The encoding
   method for over-the-wire transport is not dependent on the
   specification language chosen and is outside the scope of this
   document and up to the ForCES protocol to define.

   XML is chosen as the specification language in this document, because
   XML has the advantage of being both human and machine readable with
   widely available tools support.  This document uses an XML schema to
   define the structure of the LFB library documents, as defined in
   [RFC3470] and [Schema1] and [Schema2].  While these LFB class
   definitions are not sent in the ForCES protocol, these definitions
   comply with the recommendations in RFC 3470 [RFC3470] on the use of
   XML in IETF protocols.

   By using an XML schema to define the structure for the LFB library
   documents, we have a very clear set of syntactic restrictions to go
   with the desired semantic descriptions and restrictions covered in
   this document.  As a corollary to that, if it is determined that a
   change in the syntax is needed, then a new schema will be required.
   This would be identified by a different URN to identify the namespace
   for such a new schema.








Halpern & Hadi Salim         Standards Track                    [Page 7]


RFC 5812                     ForCES FE Model                  March 2010


1.5.  Document Structure

   Section 3 provides a conceptual overview of the FE model, laying the
   foundation for the more detailed discussion and specifications in the
   sections that follow.  Section 4 and Section 5 constitute the core of
   the FE model, detailing the two major aspects of the FE model: a
   general LFB model and a definition of the FE Object LFB, with its
   components, including FE capabilities and LFB topology information.
   Section 6 directly addresses the model requirements imposed by the
   ForCES requirements defined in RFC 3654 [RFC3654], while Section 7
   explains how the FE model should be used in the ForCES protocol.

2.  Definitions

   The use of compliance terminology (MUST, SHOULD, MAY, MUST NOT) is
   used in accordance with RFC 2119 [RFC2119].  Such terminology is used
   in describing the required behavior of ForCES forwarding elements or
   control elements in supporting or manipulating information described
   in this model.

   Terminology associated with the ForCES requirements is defined in RFC
   3654 [RFC3654] and is not copied here.  The following list of
   terminology relevant to the FE model is defined in this section.

   FE Model:  The FE model is designed to model the logical processing
      functions of an FE.  The FE model proposed in this document
      includes three components; the LFB modeling of individual Logical
      Functional Block (LFB model), the logical interconnection between
      LFBs (LFB topology), and the FE-level attributes, including FE
      capabilities.  The FE model provides the basis to define the
      information elements exchanged between the CE and the FE in the
      ForCES protocol [RFC5810].

   Data Path:  A conceptual path taken by packets within the forwarding
      plane inside an FE.  Note that more than one data path can exist
      within an FE.

   LFB (Logical Functional Block) Class (or type):  A template that
      represents a fine-grained, logically separable aspect of FE
      processing.  Most LFBs relate to packet processing in the data
      path.  LFB classes are the basic building blocks of the FE model.

   LFB Instance:  As a packet flows through an FE along a data path, it
      flows through one or multiple LFB instances, where each LFB is an
      instance of a specific LFB class.  Multiple instances of the same
      LFB class can be present in an FE's data path.  Note that we often





Halpern & Hadi Salim         Standards Track                    [Page 8]


RFC 5812                     ForCES FE Model                  March 2010


      refer to LFBs without distinguishing between an LFB class and LFB
      instance when we believe the implied reference is obvious for the
      given context.

   LFB Model:  The LFB model describes the content and structures in an
      LFB, plus the associated data definition.  XML is used to provide
      a formal definition of the necessary structures for the modeling.
      Four types of information are defined in the LFB model.  The core
      part of the LFB model is the LFB class definitions; the other
      three types of information define constructs associated with and
      used by the class definition.  These are reusable data types,
      supported frame (packet) formats, and metadata.

   Element:  Element is generally used in this document in accordance
      with the XML usage of the term.  It refers to an XML tagged part
      of an XML document.  For a precise definition, please see the full
      set of XML specifications from the W3C.  This term is included in
      this list for completeness because the ForCES formal model uses
      XML.

   Attribute:  Attribute is used in the ForCES formal modeling in
      accordance with standard XML usage of the term, i.e., to provide
      attribute information included in an XML tag.

   LFB Metadata:  Metadata is used to communicate per-packet state from
      one LFB to another, but is not sent across the network.  The FE
      model defines how such metadata is identified, produced, and
      consumed by the LFBs, but not how the per-packet state is
      implemented within actual hardware.  Metadata is sent between the
      FE and the CE on redirect packets.

   ForCES Component:  A ForCES Component is a well-defined, uniquely
      identifiable and addressable ForCES model building block.  A
      component has a 32-bit ID, name, type, and an optional synopsis
      description.  These are often referred to simply as components.

   LFB Component:  An LFB component is a ForCES component that defines
      the Operational parameters of the LFBs that must be visible to the
      CEs.

   Structure Component:  A ForCES component that is part of a complex
      data structure to be used in LFB data definitions.  The individual
      parts that make up a structured set of data are referred to as
      structure components.  These can themselves be of any valid data
      type, including tables and structures.






Halpern & Hadi Salim         Standards Track                    [Page 9]


RFC 5812                     ForCES FE Model                  March 2010


   Property:  ForCES components have properties associated with them,
      such as readability.  Other examples include lengths for variable-
      sized components.  These properties are accessed by the CE for
      reading (or, where appropriate, writing.)  Details on the ForCES
      properties are found in Section 4.8.

   LFB Topology:  LFB topology is a representation of the logical
      interconnection and the placement of LFB instances along the data
      path within one FE.  Sometimes this representation is called
      intra-FE topology, to be distinguished from inter-FE topology.
      LFB topology is outside of the LFB model, but is part of the FE
      model.

   FE Topology:  FE topology is a representation of how multiple FEs
      within a single network element (NE) are interconnected.
      Sometimes this is called inter-FE topology, to be distinguished
      from intra-FE topology (i.e., LFB topology).  An individual FE
      might not have the global knowledge of the full FE topology, but
      the local view of its connectivity with other FEs is considered to
      be part of the FE model.  The FE topology is discovered by the
      ForCES base protocol or by some other means.

   Inter-FE Topology:  See FE Topology.

   Intra-FE Topology:  See LFB Topology.

   LFB Class Library:  The LFB class library is a set of LFB classes
      that has been identified as the most common functions found in
      most FEs and hence should be defined first by the ForCES Working
      Group.

3.  ForCES Model Concepts

   Some of the important ForCES concepts used throughout this document
   are introduced in this section.  These include the capability and
   state abstraction, the FE and LFB model construction, and the unique
   addressing of the different model structures.  Details of these
   aspects are described in Section 4 and Section 5.  The intent of this
   section is to discuss these concepts at the high level and lay the
   foundation for the detailed description in the following sections.

   The ForCES FE model includes both a capability and a state
   abstraction.

   o  The FE/LFB capability model describes the capabilities and
      capacities of an FE/LFB by specifying the variation in functions
      supported and any limitations.  Capacity describes the limits of
      specific components (an example would be a table size limit).



Halpern & Hadi Salim         Standards Track                   [Page 10]


RFC 5812                     ForCES FE Model                  March 2010


   o  The state model describes the current state of the FE/LFB, that
      is, the instantaneous values or operational behavior of the FE/
      LFB.

   Section 3.1 explains the difference between a capability model and a
   state model, and describes how the two can be combined in the FE
   model.

   The ForCES model construction laid out in this document allows an FE
   to provide information about its structure for operation.  This can
   be thought of as FE-level information and information about the
   individual instances of LFBs provided by the FE.

   o  The ForCES model includes the constructions for defining the class
      of Logical Functional Blocks (LFBs) that an FE may support.  These
      classes are defined in this and other documents.  The definition
      of such a class provides the information content for monitoring
      and controlling instances of the LFB class for ForCES purposes.
      Each LFB model class formally defines the operational LFB
      components, LFB capabilities, and LFB events.  Essentially,
      Section 3.2 introduces the concept of LFBs as the basic functional
      building blocks in the ForCES model.

   o  The FE model also provides the construction necessary to monitor
      and control the FE as a whole for ForCES purposes.  For
      consistency of operation and simplicity, this information is
      represented as an LFB, the FE Object LFB class and a singular LFB
      instance of that class, defined using the LFB model.  The FE
      Object class defines the components to provide information at the
      FE level, particularly the capabilities of the FE at a coarse
      level, i.e., not all possible capabilities or all details about
      the capabilities of the FE.  Part of the FE-level information is
      the LFB topology, which expresses the logical inter-connection
      between the LFB instances along the data path(s) within the FE.
      Section 3.3 discusses the LFB topology.  The FE Object also
      includes information about what LFB classes the FE can support.

   The ForCES model allows for unique identification of the different
   constructs it defines.  This includes identification of the LFB
   classes, and of LFB instances within those classes, as well as
   identification of components within those instances.

   The ForCES protocol [RFC5810] encapsulates target address(es) to
   eventually get to a fine-grained entity being referenced by the CE.
   The addressing hierarchy is broken into the following:

   o  An FE is uniquely identified by a 32-bit FEID.




Halpern & Hadi Salim         Standards Track                   [Page 11]


RFC 5812                     ForCES FE Model                  March 2010


   o  Each class of LFB is uniquely identified by a 32-bit LFB ClassID.
      The LFB ClassIDs are global within the network element and may be
      issued by IANA.

   o  Within an FE, there can be multiple instances of each LFB class.
      Each LFB class instance is identified by a 32-bit identifier that
      is unique within a particular LFB class on that FE.

   o  All the components within an LFB instance are further defined
      using 32-bit identifiers.

   Refer to Section 3.3 for more details on addressing.

3.1.  ForCES Capability Model and State Model

   Capability and state modeling applies to both the FE and LFB
   abstraction.

   Figure 1 shows the concepts of FE state, capabilities, and
   configuration in the context of CE-FE communication via the ForCES
   protocol.

   +-------+                                          +-------+
   |       | FE capabilities: what it can/cannot do.  |       |
   |       |<-----------------------------------------|       |
   |       |                                          |       |
   |   CE  | FE state: what it is now.                |  FE   |
   |       |<-----------------------------------------|       |
   |       |                                          |       |
   |       | FE configuration: what it should be.     |       |
   |       |----------------------------------------->|       |
   +-------+                                          +-------+

    Figure 1: Illustration of FE capabilities, state, and configuration
        exchange in the context of CE-FE communication via ForCES.

3.1.1.  FE Capability Model and State Model

   Conceptually, the FE capability model tells the CE which states are
   allowed on an FE, with capacity information indicating certain
   quantitative limits or constraints.  Thus, the CE has general
   knowledge about configurations that are applicable to a particular
   FE.








Halpern & Hadi Salim         Standards Track                   [Page 12]


RFC 5812                     ForCES FE Model                  March 2010


3.1.1.1.  FE Capability Model

   The FE capability model may be used to describe an FE at a coarse
   level.  For example, an FE might be defined as follows:

   o  the FE can handle IPv4 and IPv6 forwarding;

   o  the FE can perform classification based on the following fields:
      source IP address, destination IP address, source port number,
      destination port number, etc.;

   o  the FE can perform metering;

   o  the FE can handle up to N queues (capacity); and

   o  the FE can add and remove encapsulating headers of types including
      IPsec, GRE, L2TP.

   While one could try to build an object model to fully represent the
   FE capabilities, other efforts found this approach to be a
   significant undertaking.  The main difficulty arises in describing
   detailed limits, such as the maximum number of classifiers, queues,
   buffer pools, and meters that the FE can provide.  We believe that a
   good balance between simplicity and flexibility can be achieved for
   the FE model by combining coarse-level-capability reporting with an
   error reporting mechanism.  That is, if the CE attempts to instruct
   the FE to set up some specific behavior it cannot support, the FE
   will return an error indicating the problem.  Examples of similar
   approaches include Diffserv PIB RFC 3317 [RFC3317] and framework PIB
   RFC 3318 [RFC3318].

3.1.1.2.  FE State Model

   The FE state model presents the snapshot view of the FE to the CE.
   For example, using an FE state model, an FE might be described to its
   corresponding CE as the following:

   o  on a given port, the packets are classified using a given
      classification filter;

   o  the given classifier results in packets being metered in a certain
      way and then marked in a certain way;

   o  the packets coming from specific markers are delivered into a
      shared queue for handling, while other packets are delivered to a
      different queue; and





Halpern & Hadi Salim         Standards Track                   [Page 13]


RFC 5812                     ForCES FE Model                  March 2010


   o  a specific scheduler with specific behavior and parameters will
      service these collected queues.

3.1.1.3.  LFB Capability and State Model

   Both LFB capability and state information are defined formally using
   the LFB modeling XML schema.

   Capability information at the LFB level is an integral part of the
   LFB model and provides for powerful semantics.  For example, when
   certain features of an LFB class are optional, the CE needs to be
   able to determine whether those optional features are supported by a
   given LFB instance.  The schema for the definition of LFB classes
   provides a means for identifying such components.

   State information is defined formally using LFB component constructs.

3.1.2.  Relating LFB and FE Capability and State Model

   Capability information at the FE level describes the LFB classes that
   the FE can instantiate, the number of instances of each that can be
   created, the topological (linkage) limitations between these LFB
   instances, etc.  Section 5 defines the FE-level components including
   capability information.  Since all information is represented as
   LFBs, this is provided by a single instance of the FE Object LFB
   class.  By using a single instance with a known LFB class and a known
   instance identification, the ForCES protocol can allow a CE to access
   this information whenever it needs to, including while the CE is
   establishing the control of the FE.

   Once the FE capability is described to the CE, the FE state
   information can be represented at two levels.  The first level is the
   logically separable and distinct packet processing functions, called
   LFBs.  The second level of information describes how these individual
   LFBs are ordered and placed along the data path to deliver a complete
   forwarding plane service.  The interconnection and ordering of the
   LFBs is called LFB topology.  Section 3.2 discusses high-level
   concepts around LFBs, whereas Section 3.3 discusses LFB topology
   issues.  This topology information is represented as components of
   the FE Object LFB instance, to allow the CE to fetch and manipulate
   this.

3.2.   Logical Functional Block (LFB) Modeling

   Each LFB performs a well-defined action or computation on the packets
   passing through it.  Upon completion of its prescribed function,
   either the packets are modified in certain ways (e.g., decapsulator,
   marker), or some results are generated and stored, often in the form



Halpern & Hadi Salim         Standards Track                   [Page 14]


RFC 5812                     ForCES FE Model                  March 2010


   of metadata (e.g., classifier).  Each LFB typically performs a single
   action.  Classifiers, shapers, and meters are all examples of such
   LFBs.  Modeling LFBs at such a fine granularity allows us to use a
   small number of LFBs to express the higher-order FE functions (such
   as an IPv4 forwarder) precisely, which in turn can describe more
   complex networking functions and vendor implementations of software
   and hardware.  These fine-grained LFBs will be defined in detail in
   one or more documents to be published separately, using the material
   in this model.

   It is also the case that LFBs may exist in order to provide a set of
   components for control of FE operation by the CE (i.e., a locus of
   control), without tying that control to specific packets or specific
   parts of the data path.  An example of such an LFB is the FE Object,
   which provides the CE with information about the FE as a whole, and
   allows the FE to control some aspects of the FE, such as the data
   path itself.  Such LFBs will not have the packet-oriented properties
   described in this section.

   In general, multiple LFBs are contained in one FE, as shown in
   Figure 2, and all the LFBs share the same ForCES protocol (Fp)
   termination point that implements the ForCES protocol logic and
   maintains the communication channel to and from the CE.




























Halpern & Hadi Salim         Standards Track                   [Page 15]


RFC 5812                     ForCES FE Model                  March 2010


                             +-----------+
                             |    CE     |
                             +-----------+
                                   ^
                                   | Fp reference point
                                   |
        +--------------------------|-----------------------------------+
        | FE                       |                                   |
        |                          v                                   |
        | +----------------------------------------------------------+ |
        | |                ForCES protocol                           | |
        | |                   termination point                      | |
        | +----------------------------------------------------------+ |
        |           ^                            ^                     |
        |           :                            : Internal control    |
        |           :                            :                     |
        |       +---:----------+             +---:----------|          |
        |       |   :LFB1      |             |   :     LFB2 |          |
        | =====>|   v          |============>|   v          |======>...|
        | Inputs| +----------+ |Outputs      | +----------+ |          |
        | (P,M) | |Components| |(P',M')      | |Components| |(P",M")   |
        |       | +----------+ |             | +----------+ |          |
        |       +--------------+             +--------------+          |
        |                                                              |
        +--------------------------------------------------------------+

                      Figure 2: Generic LFB diagram.

   An LFB, as shown in Figure 2, may have inputs, outputs, and
   components that can be queried and manipulated by the CE via an Fp
   reference point (defined in RFC 3746 [RFC3746]) and the ForCES
   protocol termination point.  The horizontal axis is in the forwarding
   plane for connecting the inputs and outputs of LFBs within the same
   FE.  P (with marks to indicate modification) indicates a data packet,
   while M (with marks to indicate modification) indicates the metadata
   associated with a packet.  The vertical axis between the CE and the
   FE denotes the Fp reference point where bidirectional communication
   between the CE and FE occurs: the CE-to-FE communication is for
   configuration, control, and packet injection, while the FE-to-CE
   communication is used for packet redirection to the control plane,
   reporting of monitoring and accounting information, reporting of
   errors, etc.  Note that the interaction between the CE and the LFB is
   only abstract and indirect.  The result of such an interaction is for
   the CE to manipulate the components of the LFB instances.

   An LFB can have one or more inputs.  Each input takes a pair of a
   packet and its associated metadata.  Depending upon the LFB input
   port definition, the packet or the metadata may be allowed to be



Halpern & Hadi Salim         Standards Track                   [Page 16]


RFC 5812                     ForCES FE Model                  March 2010


   empty (or equivalently to not be provided).  When input arrives at an
   LFB, either the packet or its associated metadata must be non-empty
   or there is effectively no input.  (LFB operation generally may be
   triggered by input arrival, by timers, or by other system state.  It
   is only in the case where the goal is to have input drive operation
   that the input must be non-empty.)

   The LFB processes the input, and produces one or more outputs, each
   of which is a pair of a packet and its associated metadata.  Again,
   depending upon the LFB output port definition, either the packet or
   the metadata may be allowed to be empty (or equivalently to be
   absent).  Metadata attached to packets on output may be metadata that
   was received, or may be information about the packet processing that
   may be used by later LFBs in the FEs packet processing.

   A namespace is used to associate a unique name and ID with each LFB
   class.  The namespace MUST be extensible so that a new LFB class can
   be added later to accommodate future innovation in the forwarding
   plane.

   LFB operation is specified in the model to allow the CE to understand
   the behavior of the forwarding data path.  For instance, the CE needs
   to understand at what point in the data path the IPv4 header TTL is
   decremented by the FE.  That is, the CE needs to know if a control
   packet could be delivered to it either before or after this point in
   the data path.  In addition, the CE needs to understand where and
   what type of header modifications (e.g., tunnel header append or
   strip) are performed by the FEs.  Further, the CE works to verify
   that the various LFBs along a data path within an FE are compatible
   to link together.  Connecting incompatible LFB instances will produce
   a non-working data path.  So the model is designed to provide
   sufficient information for the CE to make this determination.

   Selecting the right granularity for describing the functions of the
   LFBs is an important aspect of this model.  There is value to vendors
   if the operation of LFB classes can be expressed in sufficient detail
   so that physical devices implementing different LFB functions can be
   integrated easily into an FE design.  However, the model, and the
   associated library of LFBs, must not be so detailed and so specific
   as to significantly constrain implementations.  Therefore, a semi-
   formal specification is needed; that is, a text description of the
   LFB operation (human readable), but sufficiently specific and
   unambiguous to allow conformance testing and efficient design, so
   that interoperability between different CEs and FEs can be achieved.







Halpern & Hadi Salim         Standards Track                   [Page 17]


RFC 5812                     ForCES FE Model                  March 2010


   The LFB class model specifies the following, among other information:

   o  number of inputs and outputs (and whether they are configurable)

   o  metadata read/consumed from inputs

   o  metadata produced at the outputs

   o  packet types accepted at the inputs and emitted at the outputs

   o  packet content modifications (including encapsulation or
      decapsulation)

   o  packet routing criteria (when multiple outputs on an LFB are
      present)

   o  packet timing modifications

   o  packet flow ordering modifications

   o  LFB capability information components

   o  events that can be detected by the LFB, with notification to the
      CE

   o  LFB operational components

   Section 4 of this document provides a detailed discussion of the LFB
   model with a formal specification of LFB class schema.  The rest of
   Section 3.2 only intends to provide a conceptual overview of some
   important issues in LFB modeling, without covering all the specific
   details.

3.2.1.  LFB Outputs

   An LFB output is a conceptual port on an LFB that can send
   information to another LFB.  The information sent on that port is a
   pair of a packet and associated metadata, one of which may be empty.
   (If both were empty, there would be no output.)

   A single LFB output can be connected to only one LFB input.  This is
   required to make the packet flow through the LFB topology
   unambiguous.

   Some LFBs will have a single output, as depicted in Figure 3.a.






Halpern & Hadi Salim         Standards Track                   [Page 18]


RFC 5812                     ForCES FE Model                  March 2010


    +---------------+               +-----------------+
    |               |               |                 |
    |               |               |             OUT +-->
    ...          OUT +-->           ...               |
    |               |               |    EXCEPTIONOUT +-->
    |               |               |                 |
    +---------------+               +-----------------+

    a. One output               b. Two distinct outputs

    +---------------+               +-----------------+
    |               |               |    EXCEPTIONOUT +-->
    |         OUT:1 +-->            |                 |
    ...       OUT:2 +-->           ...          OUT:1 +-->
    |         ...   +...            |           OUT:2 +-->
    |         OUT:n +-->            |           ...   +...
    +---------------+               |           OUT:n +-->
                                    +-----------------+

    c. One output group       d. One output and one output group

       Figure 3: Examples of LFBs with various output combinations.

   To accommodate a non-trivial LFB topology, multiple LFB outputs are
   needed so that an LFB class can fork the data path.  Two mechanisms
   are provided for forking: multiple singleton outputs and output
   groups, which can be combined in the same LFB class.

   Multiple separate singleton outputs are defined in an LFB class to
   model a predetermined number of semantically different outputs.  That
   is, the LFB class definition MUST include the number of outputs,
   implying the number of outputs is known when the LFB class is
   defined.  Additional singleton outputs cannot be created at LFB
   instantiation time, nor can they be created on the fly after the LFB
   is instantiated.

   For example, an IPv4 LPM (Longest-Prefix-Matching) LFB may have one
   output (OUT) to send those packets for which the LPM look-up was
   successful, passing a META_ROUTEID as metadata; and have another
   output (EXCEPTIONOUT) for sending exception packets when the LPM
   look-up failed.  This example is depicted in Figure 3.b.  Packets
   emitted by these two outputs not only require different downstream
   treatment, but they are a result of two different conditions in the
   LFB and each output carries different metadata.  This concept assumes
   that the number of distinct outputs is known when the LFB class is
   defined.  For each singleton output, the LFB class definition defines
   the types of frames (packets) and metadata the output emits.




Halpern & Hadi Salim         Standards Track                   [Page 19]


RFC 5812                     ForCES FE Model                  March 2010


   An output group, on the other hand, is used to model the case where a
   flow of similar packets with an identical set of permitted metadata
   needs to be split into multiple paths.  In this case, the number of
   such paths is not known when the LFB class is defined because it is
   not an inherent property of the LFB class.  An output group consists
   of a number of outputs, called the output instances of the group,
   where all output instances share the same frame (packet) and metadata
   emission definitions (see Figure 3.c).  Each output instance can
   connect to a different downstream LFB, just as if they were separate
   singleton outputs, but the number of output instances can differ
   between LFB instances of the same LFB class.  The class definition
   may include a lower and/or an upper limit on the number of outputs.
   In addition, for configurable FEs, the FE capability information may
   define further limits on the number of instances in specific output
   groups for certain LFBs.  The actual number of output instances in a
   group is a component of the LFB instance, which is read-only for
   static topologies, and read-write for dynamic topologies.  The output
   instances in a group are numbered sequentially, from 0 to N-1, and
   are addressable from within the LFB.  To use Output Port groups, the
   LFB has to have a built-in mechanism to select one specific output
   instance for each packet.  This mechanism is described in the textual
   definition of the class and is typically configurable via some
   attributes of the LFB.

   For example, consider a redirector LFB, whose sole purpose is to
   direct packets to one of N downstream paths based on one of the
   metadata associated with each arriving packet.  Such an LFB is fairly
   versatile and can be used in many different places in a topology.
   For example, given LFBs that record the type of packet in a FRAMETYPE
   metadatum, or a packet rate class in a COLOR metadatum, one may uses
   these metadata for branching.  A redirector can be used to divide the
   data path into an IPv4 and an IPv6 path based on a FRAMETYPE
   metadatum (N=2), or to fork into rate-specific paths after metering
   using the COLOR metadatum (red, yellow, green; N=3), etc.

   Using an output group in the above LFB class provides the desired
   flexibility to adapt each instance of this class to the required
   operation.  The metadata to be used as a selector for the output
   instance is a property of the LFB.  For each packet, the value of the
   specified metadata may be used as a direct index to the output
   instance.  Alternatively, the LFB may have a configurable selector
   table that maps a metadatum value to output instance.

   Note that other LFBs may also use the output group concept to build
   in similar adaptive forking capability.  For example, a classifier
   LFB with one input and N outputs can be defined easily by using the
   output group concept.  Alternatively, a classifier LFB with one
   singleton output in combination with an explicit N-output re-director



Halpern & Hadi Salim         Standards Track                   [Page 20]


RFC 5812                     ForCES FE Model                  March 2010


   LFB models the same processing behavior.  The decision of whether to
   use the output group model for a certain LFB class is left to the LFB
   class designers.

   The model allows the output group to be combined with other singleton
   output(s) in the same class, as demonstrated in Figure 3.d.  The LFB
   here has two types of outputs, OUT, for normal packet output, and
   EXCEPTIONOUT, for packets that triggered some exception.  The normal
   OUT has multiple instances; thus, it is an output group.

   In summary, the LFB class may define one output, multiple singleton
   outputs, one or more output groups, or a combination thereof.
   Multiple singleton outputs should be used when the LFB must provide
   for forking the data path and at least one of the following
   conditions hold:

   o  the number of downstream directions is inherent from the
      definition of the class and hence fixed

   o  the frame type and set of permitted metadata emitted on any of the
      outputs are different from what is emitted on the other outputs
      (i.e., they cannot share their frametype and permitted metadata
      definitions)

   An output group is appropriate when the LFB must provide for forking
   the data path and at least one of the following conditions hold:

   o  the number of downstream directions is not known when the LFB
      class is defined

   o  the frame type and set of metadata emitted on these outputs are
      sufficiently similar or, ideally, identical, such they can share
      the same output definition

3.2.2.  LFB Inputs

   An LFB input is a conceptual port on an LFB on which the LFB can
   receive information from other LFBs.  The information is typically a
   pair of a packet and its associated metadata.  Either the packet or
   the metadata may for some LFBs and some situations be empty.  They
   cannot both be empty, as then there is no input.

   For LFB instances that receive packets from more than one other LFB
   instance (fan-in), there are three ways to model fan-in, all
   supported by the LFB model and can all be combined in the same LFB:

   o  Implicit multiplexing via a single input




Halpern & Hadi Salim         Standards Track                   [Page 21]


RFC 5812                     ForCES FE Model                  March 2010


   o  Explicit multiplexing via multiple singleton inputs

   o  Explicit multiplexing via a group of inputs (input group)

   The simplest form of multiplexing uses a singleton input
   (Figure 4.a).  Most LFBs will have only one singleton input.
   Multiplexing into a single input is possible because the model allows
   more than one LFB output to connect to the same LFB input.  This
   property applies to any LFB input without any special provisions in
   the LFB class.  Multiplexing into a single input is applicable when
   the packets from the upstream LFBs are similar in frametype and
   accompanying metadata, and require similar processing.  Note that
   this model does not address how potential contention is handled when
   multiple packets arrive simultaneously.  If contention handling needs
   to be explicitly modeled, one of the other two modeling solutions
   must be used.

   The second method to model fan-in uses individually defined singleton
   inputs (Figure 4.b).  This model is meant for situations where the
   LFB needs to handle distinct types of packet streams, requiring
   input-specific handling inside the LFB, and where the number of such
   distinct cases is known when the LFB class is defined.  For example,
   an LFB that can perform both Layer 2 decapsulation (to Layer 3) and
   Layer 3 encapsulation (to Layer 2) may have two inputs, one for
   receiving Layer 2 frames for decapsulation, and one for receiving
   Layer 3 frames for encapsulation.  This LFB type expects different
   frames (L2 versus L3) at its inputs, each with different sets of
   metadata, and would thus apply different processing on frames
   arriving at these inputs.  This model is capable of explicitly
   addressing packet contention by defining how the LFB class handles
   the contending packets.

   +--------------+       +------------------------+
   | LFB X        +---+   |                        |
   +--------------+   |   |                        |
                      |   |                        |
   +--------------+   v   |                        |
   | LFB Y        +---+-->|input     Meter LFB     |
   +--------------+   ^   |                        |
                      |   |                        |
   +--------------+   |   |                        |
   | LFB Z        |---+   |                        |
   +--------------+       +------------------------+

   (a) An LFB connects with multiple upstream LFBs via a single input.






Halpern & Hadi Salim         Standards Track                   [Page 22]


RFC 5812                     ForCES FE Model                  March 2010


   +--------------+       +------------------------+
   | LFB X        +---+   |                        |
   +--------------+   +-->|layer2                  |
   +--------------+       |                        |
   | LFB Y        +------>|layer3     LFB          |
   +--------------+       +------------------------+

   (b) An LFB connects with multiple upstream LFBs via two separate
   singleton inputs.

   +--------------+       +------------------------+
   | Queue LFB #1 +---+   |                        |
   +--------------+   |   |                        |
                      |   |                        |
   +--------------+   +-->|in:0   \                |
   | Queue LFB #2 +------>|in:1   | input group    |
   +--------------+       |...    |                |
                      +-->|in:N-1 /                |
   ...                |   |                        |
   +--------------+   |   |                        |
   | Queue LFB #N |---+   |     Scheduler LFB      |
   +--------------+       +------------------------+

   (c) A Scheduler LFB uses an input group to differentiate which queue
   LFB packets are coming from.

        Figure 4: Examples of LFBs with various input combinations.

   The third method to model fan-in uses the concept of an input group.
   The concept is similar to the output group introduced in the previous
   section and is depicted in Figure 4.c.  An input group consists of a
   number of input instances, all sharing the properties (same frame and
   metadata expectations).  The input instances are numbered from 0 to
   N-1.  From the outside, these inputs appear as normal inputs, i.e.,
   any compatible upstream LFB can connect its output to one of these
   inputs.  When a packet is presented to the LFB at a particular input
   instance, the index of the input where the packet arrived is known to
   the LFB and this information may be used in the internal processing.
   For example, the input index can be used as a table selector, or as
   an explicit precedence selector to resolve contention.  As with
   output groups, the number of input instances in an input group is not
   defined in the LFB class.  However, the class definition may include
   restrictions on the range of possible values.  In addition, if an FE
   supports configurable topologies, it may impose further limitations
   on the number of instances for particular port group(s) of a
   particular LFB class.  Within these limitations, different instances
   of the same class may have a different number of input instances.




Halpern & Hadi Salim         Standards Track                   [Page 23]


RFC 5812                     ForCES FE Model                  March 2010


   The number of actual input instances in the group is a component
   defined in the LFB class, which is read-only for static topologies,
   and is read-write for configurable topologies.

   As an example for the input group, consider the Scheduler LFB
   depicted in Figure 4.c.  Such an LFB receives packets from a number
   of Queue LFBs via a number of input instances, and uses the input
   index information to control contention resolution and scheduling.

   In summary, the LFB class may define one input, multiple singleton
   inputs, one or more input groups, or a combination thereof.  Any
   input allows for implicit multiplexing of similar packet streams via
   connecting multiple outputs to the same input.  Explicit multiple
   singleton inputs are useful when either the contention handling must
   be handled explicitly or when the LFB class must receive and process
   a known number of distinct types of packet streams.  An input group
   is suitable when contention handling must be modeled explicitly, but
   the number of inputs is not inherent from the class (and hence is not
   known when the class is defined), or when it is critical for LFB
   operation to know exactly on which input the packet was received.

3.2.3.  Packet Type

   When LFB classes are defined, the input and output packet formats
   (e.g., IPv4, IPv6, Ethernet) MUST be specified.  These are the types
   of packets that a given LFB input is capable of receiving and
   processing, or that a given LFB output is capable of producing.  This
   model requires that distinct packet types be uniquely labeled with a
   symbolic name and/or ID.

   Note that each LFB has a set of packet types that it operates on, but
   does not care whether the underlying implementation is passing a
   greater portion of the packets.  For example, an IPv4 LFB might only
   operate on IPv4 packets, but the underlying implementation may or may
   not be stripping the L2 header before handing it over.  Whether or
   not such processing is happening is opaque to the CE.

3.2.4.  Metadata

   Metadata is state that is passed from one LFB to another alongside a
   packet.  The metadata passed with the packet assists subsequent LFBs
   to process that packet.

   The ForCES model defines metadata as precise atomic definitions in
   the form of label, value pairs.






Halpern & Hadi Salim         Standards Track                   [Page 24]


RFC 5812                     ForCES FE Model                  March 2010


   The ForCES model provides to the authors of LFB classes a way to
   formally define how to achieve metadata creation, modification,
   reading, as well as consumption (deletion).

   Inter-FE metadata, i.e., metadata crossing FEs, while it is likely to
   be semantically similar to this metadata, is out of scope for this
   document.

   Section 4 has informal details on metadata.

3.2.4.1.  Metadata Lifecycle within the ForCES Model

   Each metadatum is modeled as a <label, value> pair, where the label
   identifies the type of information (e.g., "color"), and its value
   holds the actual information (e.g., "red").  The label here is shown
   as a textual label, but for protocol processing it is associated with
   a unique numeric value (identifier).

   To ensure inter-operability between LFBs, the LFB class specification
   must define what metadata the LFB class "reads" or "consumes" on its
   input(s) and what metadata it "produces" on its output(s).  For
   maximum extensibility, this definition should specify neither which
   LFBs the metadata is expected to come from for a consumer LFB nor
   which LFBs are expected to consume metadata for a given producer LFB.

3.2.4.2.  Metadata Production and Consumption

   For a given metadatum on a given packet path, there MUST be at least
   one producer LFB that creates that metadatum and SHOULD be at least
   one consumer LFB that needs that metadatum.

   In the ForCES model, the producer and consumer LFBs of a metadatum
   are not required to be adjacent.  In addition, there may be multiple
   producers and consumers for the same metadatum.  When a packet path
   involves multiple producers of the same metadatum, then subsequent
   producers overwrite that metadatum value.

   The metadata that is produced by an LFB is specified by the LFB class
   definition on a per-output-port-group basis.  A producer may always
   generate the metadata on the port group, or may generate it only
   under certain conditions.  We call the former "unconditional"
   metadata, whereas the latter is "conditional" metadata.  For example,
   deep packet inspection LFB might produce several pieces of metadata
   about the packet.  The first metadatum might be the IP protocol (TCP,
   UDP, SCTP, ...) being carried, and two additional metadata items
   might be the source and destination port number.  These additional
   metadata items are conditional on the value of the first metadatum
   (IP carried protocol) as they are only produced for protocols that



Halpern & Hadi Salim         Standards Track                   [Page 25]


RFC 5812                     ForCES FE Model                  March 2010


   use port numbers.  In the case of conditional metadata, it should be
   possible to determine from the definition of the LFB when
   "conditional" metadata is produced.  The consumer behavior of an LFB,
   that is, the metadata that the LFB needs for its operation, is
   defined in the LFB class definition on a per-input-port-group basis.
   An input port group may "require" a given metadatum, or may treat it
   as "optional" information.  In the latter case, the LFB class
   definition MUST explicitly define what happens if any optional
   metadata is not provided.  One approach is to specify a default value
   for each optional metadatum, and assume that the default value is
   used for any metadata that is not provided with the packet.

   When specifying the metadata tags, some harmonization effort must be
   made so that the producer LFB class uses the same tag as its intended
   consumer(s).

3.2.4.3.  LFB Operations on Metadata

   When the packet is processed by an LFB (i.e., between the time it is
   received and forwarded by the LFB), the LFB may perform read, write,
   and/or consume operations on any active metadata associated with the
   packet.  If the LFB is considered to be a black box, one of the
   following operations is performed on each active metadatum.

      *  IGNORE: ignores and forwards the metadatum

      *  READ: reads and forwards the metadatum

      *  READ/RE-WRITE: reads, over-writes, and forwards the metadatum

      *  WRITE: writes and forwards the metadatum (can also be used to
         create new metadata)

      *  READ-AND-CONSUME: reads and consumes the metadatum

      *  CONSUME: consumes metadatum without reading

   The last two operations terminate the life-cycle of the metadatum,
   meaning that the metadatum is not forwarded with the packet when the
   packet is sent to the next LFB.

   In the ForCES model, a new metadatum is generated by an LFB when the
   LFB applies a WRITE operation to a metadatum type that was not
   present when the packet was received by the LFB.  Such implicit
   creation may be unintentional by the LFB; that is, the LFB may apply
   the WRITE operation without knowing or caring whether or not the
   given metadatum existed.  If it existed, the metadatum gets over-
   written; if it did not exist, the metadatum is created.



Halpern & Hadi Salim         Standards Track                   [Page 26]


RFC 5812                     ForCES FE Model                  March 2010


   For LFBs that insert packets into the model, WRITE is the only
   meaningful metadata operation.

   For LFBs that remove the packet from the model, they may either READ-
   AND-CONSUME (read) or CONSUME (ignore) each active metadatum
   associated with the packet.

3.2.5.  LFB Events

   During operation, various conditions may occur that can be detected
   by LFBs.  Examples range from link failure or restart to timer
   expiration in special purpose LFBs.  The CE may wish to be notified
   of the occurrence of such events.  The description of how such
   messages are sent, and their format, is part of the Forwarding and
   Control Element Separation (ForCES) protocol [RFC5810] document.
   Indicating how such conditions are understood is part of the job of
   this model.

   Events are declared in the LFB class definition.  The LFB event
   declaration constitutes:

   o  a unique 32-bit identifier.

   o  An LFB component that is used to trigger the event.  This entity
      is known as the event target.

   o  A condition that will happen to the event target that will result
      in a generation of an event to the CE.  Examples of a condition
      include something getting created or deleted, a config change,
      etc.

   o  What should be reported to the CE by the FE if the declared
      condition is met.

   The declaration of an event within an LFB class essentially defines
   what part of the LFB component(s) need to be monitored for events,
   what condition on the LFB monitored LFB component an FE should detect
   to trigger such an event, and what to report to the CE when the event
   is triggered.

   While events may be declared by the LFB class definition, runtime
   activity is controlled using built-in event properties using LFB
   component properties (discussed in Section 3.2.6).  A CE subscribes
   to the events on an LFB class instance by setting an event property
   for subscription.  Each event has a subscription property that is by
   default off.  A CE wishing to receive a specific event needs to turn
   on the subscription property at runtime.




Halpern & Hadi Salim         Standards Track                   [Page 27]


RFC 5812                     ForCES FE Model                  March 2010


   Event properties also provide semantics for runtime event filtering.
   A CE may set an event property to further suppress events to which it
   has already subscribed.  The LFB model defines such filters to
   include threshold values, hysteresis, time intervals, number of
   events, etc.

   The contents of reports with events are designed to allow for the
   common, closely related information that the CE can be strongly
   expected to need to react to the event.  It is not intended to carry
   information that the CE already has, large volumes of information, or
   information related in complex fashions.

   From a conceptual point of view, at runtime, event processing is
   split into:

   1.  Detection of something happening to the (declared during LFB
       class definition) event target.  Processing the next step happens
       if the CE subscribed (at runtime) to the event.

   2.  Checking of the (declared during LFB class definition) condition
       on the LFB event target.  If the condition is met, proceed with
       the next step.

   3.  Checking (runtime set) event filters if they exist to see if the
       event should be reported or suppressed.  If the event is to be
       reported, proceed to the next step.

   4.  Submitting of the declared report to the CE.

   Section 4.7.6 discusses events in more details.

3.2.6.  Component Properties

   LFBs and structures are made up of components, containing the
   information that the CE needs to see and/or change about the
   functioning of the LFB.  These components, as described in detail in
   Section 4.7, may be basic values, complex structures (containing
   multiple components themselves, each of which can be values,
   structures, or tables), or tables (which contain values, structures,
   or tables).  Components may be defined such that their appearance in
   LFB instances is optional.  Components may be readable or writable at
   the discretion of the FE implementation.  The CE needs to know these
   properties.  Additionally, certain kinds of components (arrays /
   tables, aliases, and events) have additional property information
   that the CE may need to read or write.  This model defines the
   structure of the property information for all defined data types.

   Section 4.8 describes properties in more details.



Halpern & Hadi Salim         Standards Track                   [Page 28]


RFC 5812                     ForCES FE Model                  March 2010


3.2.7.  LFB Versioning

   LFB class versioning is a method to enable incremental evolution of
   LFB classes.  In general, an FE is not allowed to contain an LFB
   instance for more than one version of a particular class.
   Inheritance (discussed next in Section 3.2.8) has special rules.  If
   an FE data path model containing an LFB instance of a particular
   class C also simultaneously contains an LFB instance of a class C'
   inherited from class C; C could have a different version than C'.

   LFB class versioning is supported by requiring a version string in
   the class definition.  CEs may support multiple versions of a
   particular LFB class to provide backward compatibility, but FEs MUST
   NOT support more than one version of a particular class.

   Versioning is not restricted to making backward-compatible changes.
   It is specifically expected to be used to make changes that cannot be
   represented by inheritance.  Often this will be to correct errors,
   and hence may not be backward compatible.  It may also be used to
   remove components that are not considered useful (particularly if
   they were previously mandatory, and hence were an implementation
   impediment).

3.2.8.  LFB Inheritance

   LFB class inheritance is supported in the FE model as a method to
   define new LFB classes.  This also allows FE vendors to add vendor-
   specific extensions to standardized LFBs.  An LFB class specification
   MUST specify the base class and version number it inherits from (the
   default is the base LFB class).  Multiple inheritance is not allowed,
   however, to avoid unnecessary complexity.

   Inheritance should be used only when there is significant reuse of
   the base LFB class definition.  A separate LFB class should be
   defined if little or no reuse is possible between the derived and the
   base LFB class.

   An interesting issue related to class inheritance is backward
   compatibility between a descendant and an ancestor class.  Consider
   the following hypothetical scenario where a standardized LFB class
   "L1" exists.  Vendor A builds an FE that implements LFB "L1", and
   vendor B builds a CE that can recognize and operate on LFB "L1".
   Suppose that a new LFB class, "L2", is defined based on the existing
   "L1" class by extending its capabilities incrementally.  Let us
   examine the FE backward-compatibility issue by considering what would
   happen if vendor B upgrades its FE from "L1" to "L2" and vendor C's





Halpern & Hadi Salim         Standards Track                   [Page 29]


RFC 5812                     ForCES FE Model                  March 2010


   CE is not changed.  The old L1-based CE can interoperate with the new
   L2-based FE if the derived LFB class "L2" is indeed backward
   compatible with the base class "L1".

   The reverse scenario is a much less problematic case, i.e., when CE
   vendor B upgrades to the new LFB class "L2", but the FE is not
   upgraded.  Note that as long as the CE is capable of working with
   older LFB classes, this problem does not affect the model; hence we
   will use the term "backward compatibility" to refer to the first
   scenario concerning FE backward compatibility.

   Backward compatibility can be designed into the inheritance model by
   constraining LFB inheritance to require that the derived class be a
   functional superset of the base class (i.e., the derived class can
   only add functions to the base class, but not remove functions).
   Additionally, the following mechanisms are required to support FE
   backward compatibility:

   1.  When detecting an LFB instance of an LFB type that is unknown to
       the CE, the CE MUST be able to query the base class of such an
       LFB from the FE.

   2.  The LFB instance on the FE SHOULD support a backward-
       compatibility mode (meaning the LFB instance reverts itself back
       to the base class instance), and the CE SHOULD be able to
       configure the LFB to run in such a mode.

3.3.  ForCES Model Addressing

   Figure 5 demonstrates the abstraction of the different ForCES model
   entities.  The ForCES protocol provides the mechanism to uniquely
   identify any of the LFB class instance components.

        FE Address = FE01
        +--------------------------------------------------------------+
        |                                                              |
        | +--------------+             +--------------+                |
        | | LFB ClassID 1|             |LFB ClassID 91|                |
        | | InstanceID 3 |============>|InstanceID 3  |======>...      |
        | | +----------+ |             | +----------+ |                |
        | | |Components| |             | |Components| |                |
        | | +----------+ |             | +----------+ |                |
        | +--------------+             +--------------+                |
        |                                                              |
        +--------------------------------------------------------------+

                      Figure 5: FE entity hierarchy.




Halpern & Hadi Salim         Standards Track                   [Page 30]


RFC 5812                     ForCES FE Model                  March 2010


   At the top of the addressing hierarchy is the FE identifier.  In the
   example above, the 32-bit FE identifier is illustrated with the
   mnemonic FE01.  The next 32-bit entity selector is the LFB ClassID.
   In the illustration above, two LFB classes with identifiers 1 and 91
   are demonstrated.  The example above further illustrates one instance
   of each of the two classes.  The scope of the 32-bit LFB class
   instance identifier is valid only within the LFB class.  To emphasize
   that point, each of class 1 and 91 has an instance of 3.

   Using the described addressing scheme, a message could be sent to
   address FE01, LFB ClassID 1, LFB InstanceID 3, utilizing the ForCES
   protocol.  However, to be effective, such a message would have to
   target entities within an LFB.  These entities could be carrying
   state, capability, etc.  These are further illustrated in Figure 6
   below.

          LFB Class ID 1,InstanceID 3 Components
          +-------------------------------------+
          |                                     |
          | LFB ComponentID 1                   |
          | +----------------------+            |
          | |                      |            |
          | +----------------------+            |
          |                                     |
          | LFB ComponentID 31                  |
          | +----------------------+            |
          | |                      |            |
          | +----------------------+            |
          |                                     |
          | LFB ComponentID 51                  |
          | +----------------------+            |
          | | LFB ComponentID 89   |            |
          | | +-----------------+  |            |
          | | |                 |  |            |
          | | +-----------------+  |            |
          | +----------------------+            |
          |                                     |
          |                                     |
          +-------------------------------------+

                         Figure 6: LFB hierarchy.

   Figure 6 zooms into the components carried by LFB Class ID 1, LFB
   InstanceID 3 from Figure 5.







Halpern & Hadi Salim         Standards Track                   [Page 31]


RFC 5812                     ForCES FE Model                  March 2010


   The example shows three components with 32-bit component identifiers
   1, 31, and 51.  LFB ComponentID 51 is a complex structure
   encapsulating within it an entity with LFB ComponentID 89.  LFB
   ComponentID 89 could be a complex structure itself, but is restricted
   in the example for the sake of clarity.

3.3.1.  Addressing LFB Components: Paths and Keys

   As mentioned above, LFB components could be complex structures, such
   as a table, or even more complex structures such as a table whose
   cells are further tables, etc.  The ForCES model XML schema
   (Section 4) allows for uniquely identifying anything with such
   complexity, utilizing the concept of dot-annotated static paths and
   content addressing of paths as derived from keys.  As an example, if
   LFB ComponentID 51 were a structure, then the path to LFB ComponentID
   89 above will be 51.89.

   LFB ComponentID 51 might represent a table (an array).  In that case,
   to select the LFB component with ID 89 from within the 7th entry of
   the table, one would use the path 51.7.89.  In addition to supporting
   explicit table element selection by including an index in the dotted
   path, the model supports identifying table elements by their
   contents.  This is referred to as using keys, or key indexing.  So,
   as a further example, if ComponentID 51 was a table that was key
   index-able, then a key describing content could also be passed by the
   CE, along with path 51 to select the table, and followed by the path
   89 to select the table structure element, which upon computation by
   the FE would resolve to the LFB ComponentID 89 within the specified
   table entry.

3.4.  FE Data Path Modeling

   Packets coming into the FE from ingress ports generally flow through
   one or more LFBs before leaving out of the egress ports.  How an FE
   treats a packet depends on many factors, such as type of the packet
   (e.g., IPv4, IPv6, or MPLS), header values, time of arrival, etc.
   The result of LFB processing may have an impact on how the packet is
   to be treated in downstream LFBs.  This differentiation of packet
   treatment downstream can be conceptualized as having alternative data
   paths in the FE.  For example, the result of a 6-tuple classification
   performed by a classifier LFB could control which rate meter is
   applied to the packet by a rate meter LFB in a later stage in the
   data path.

   LFB topology is a directed graph representation of the logical data
   paths within an FE, with the nodes representing the LFB instances and
   the directed link depicting the packet flow direction from one LFB to




Halpern & Hadi Salim         Standards Track                   [Page 32]


RFC 5812                     ForCES FE Model                  March 2010


   the next.  Section 3.4.1 discusses how the FE data paths can be
   modeled as LFB topology, while Section 3.4.2 focuses on issues
   related to LFB topology reconfiguration.

3.4.1.  Alternative Approaches for Modeling FE Data Paths

   There are two basic ways to express the differentiation in packet
   treatment within an FE; one represents the data path directly and
   graphically (topological approach) and the other utilizes metadata
   (the encoded state approach).

   o  Topological Approach

   Using this approach, differential packet treatment is expressed by
   splitting the LFB topology into alternative paths.  In other words,
   if the result of an LFB operation controls how the packet is further
   processed, then such an LFB will have separate output ports, one for
   each alternative treatment, connected to separate sub-graphs, each
   expressing the respective treatment downstream.

   o  Encoded State Approach

   An alternate way of expressing differential treatment is by using
   metadata.  The result of the operation of an LFB can be encoded in a
   metadatum, which is passed along with the packet to downstream LFBs.
   A downstream LFB, in turn, can use the metadata and its value (e.g.,
   as an index into some table) to determine how to treat the packet.

   Theoretically, either approach could substitute for the other, so one
   could consider using a single pure approach to describe all data
   paths in an FE.  However, neither model by itself results in the best
   representation for all practically relevant cases.  For a given FE
   with certain logical data paths, applying the two different modeling
   approaches will result in very different looking LFB topology graphs.
   A model using only the topological approach may require a very large
   graph with many links or paths, and nodes (i.e., LFB instances) to
   express all alternative data paths.  On the other hand, a model using
   only the encoded state model would be restricted to a string of LFBs,
   which is not an intuitive way to describe different data paths (such
   as MPLS and IPv4).  Therefore, a mix of these two approaches will
   likely be used for a practical model.  In fact, as we illustrate
   below, the two approaches can be mixed even within the same LFB.

   Using a simple example of a classifier with N classification outputs
   followed by other LFBs, Figure 7.a shows what the LFB topology looks
   like when using the pure topological approach.  Each output from the
   classifier goes to one of the N LFBs where no metadata is needed.
   The topological approach is simple, straightforward, and graphically



Halpern & Hadi Salim         Standards Track                   [Page 33]


RFC 5812                     ForCES FE Model                  March 2010


   intuitive.  However, if N is large and the N nodes following the
   classifier (LFB#1, LFB#2, ..., LFB#N) all belong to the same LFB type
   (e.g., meter), but each has its own independent components, the
   encoded state approach gives a much simpler topology representation,
   as shown in Figure 7.b.  The encoded state approach requires that a
   table of N rows of meter components be provided in the Meter node
   itself, with each row representing the attributes for one meter
   instance.  A metadatum M is also needed to pass along with the packet
   P from the classifier to the meter, so that the meter can use M as a
   look-up key (index) to find the corresponding row of the attributes
   that should be used for any particular packet P.

   What if those N nodes (LFB#1, LFB#2, ..., LFB#N) are not of the same
   type?  For example, if LFB#1 is a queue while the rest are all
   meters, what is the best way to represent such data paths?  While it
   is still possible to use either the pure topological approach or the
   pure encoded state approach, the natural combination of the two
   appears to be the best option.  Figure 7.c depicts two different
   functional data paths using the topological approach while leaving
   the N-1 meter instances distinguished by metadata only, as shown in
   Figure 7.c.

                                   +----------+
                            P      |   LFB#1  |
                        +--------->|(Compon-1)|
   +-------------+      |          +----------+
   |            1|------+   P      +----------+
   |            2|---------------->|   LFB#2  |
   | classifier 3|                 |(Compon-2)|
   |          ...|...              +----------+
   |            N|------+          ...
   +-------------+      |   P      +----------+
                        +--------->|   LFB#N  |
                                   |(Compon-N)|
                                   +----------+

   (a) Using pure topological approach














Halpern & Hadi Salim         Standards Track                   [Page 34]


RFC 5812                     ForCES FE Model                  March 2010


   +-------------+                 +-------------+
   |            1|                 |   Meter     |
   |            2|   (P, M)        | (Compon-1)  |
   |            3|---------------->| (Compon-2)  |
   |          ...|                 |   ...       |
   |            N|                 | (Compon-N)  |
   +-------------+                 +-------------+

   (b) Using pure encoded state approach to represent the LFB
   topology in 5(a), if LFB#1, LFB#2, ..., and LFB#N are of the
   same type (e.g., meter).

                                +-------------+
   +-------------+ (P, M)       | queue       |
   |            1|------------->| (Compon-1)  |
   |            2|              +-------------+
   |            3| (P, M)       +-------------+
   |          ...|------------->|   Meter     |
   |            N|              | (Compon-2)  |
   +-------------+              |   ...       |
                                | (Compon-N)  |
                                +-------------+

   (c) Using a combination of the two, if LFB#1, LFB#2, ..., and
   LFB#N are of different types (e.g., queue and meter).

            Figure 7: An example of how to model FE data paths.

   From this example, we demonstrate that each approach has a distinct
   advantage depending on the situation.  Using the encoded state
   approach, fewer connections are typically needed between a fan-out
   node and its next LFB instances of the same type because each packet
   carries metadata the following nodes can interpret and hence invoke a
   different packet treatment.  For those cases, a pure topological
   approach forces one to build elaborate graphs with many more
   connections and often results in an unwieldy graph.  On the other
   hand, a topological approach is the most intuitive for representing
   functionally different data paths.

   For complex topologies, a combination of the two is the most
   flexible.  A general design guideline is provided to indicate which
   approach is best used for a particular situation.  The topological
   approach should primarily be used when the packet data path forks to
   distinct LFB classes (not just distinct parameterizations of the same
   LFB class), and when the fan-outs do not require changes, such as
   adding/removing LFB outputs, or require only very infrequent changes.





Halpern & Hadi Salim         Standards Track                   [Page 35]


RFC 5812                     ForCES FE Model                  March 2010


   Configuration information that needs to change frequently should be
   expressed by using the internal attributes of one or more LFBs (and
   hence using the encoded state approach).

                      +---------------------------------------------+
                      |                                             |
        +----------+  V      +----------+           +------+        |
        |          |  |      |          |if IP-in-IP|      |        |
   ---->| ingress  |->+----->|classifier|---------->|Decap.|---->---+
        | ports    |         |          |---+       |      |
        +----------+         +----------+   |others +------+
                                            |
                                            V
   (a)  The LFB topology with a logical loop


       +-------+   +-----------+            +------+   +-----------+
       |       |   |           |if IP-in-IP |      |   |           |
   --->|ingress|-->|classifier1|----------->|Decap.|-->+classifier2|->
       | ports |   |           |----+       |      |   |           |
       +-------+   +-----------+    |others +------+   +-----------+
                                    |
                                    V
   (b) The LFB topology without the loop utilizing two independent
              classifier instances.

                    Figure 8: An LFB topology example.

   It is important to point out that the LFB topology described here is
   the logical topology, not the physical topology of how the FE
   hardware is actually laid out.  Nevertheless, the actual
   implementation may still influence how the functionality is mapped to
   the LFB topology.  Figure 8 shows one simple FE example.  In this
   example, an IP-in-IP packet from an IPsec application like VPN may go
   to the classifier first and have the classification done based on the
   outer IP header.  Upon being classified as an IP-in-IP packet, the
   packet is then sent to a decapsulator to strip off the outer IP
   header, followed by a classifier again to perform classification on
   the inner IP header.  If the same classifier hardware or software is
   used for both outer and inner IP header classification with the same
   set of filtering rules, a logical loop is naturally present in the
   LFB topology, as shown in Figure 8.a.  However, if the classification
   is implemented by two different pieces of hardware or software with
   different filters (i.e., one set of filters for the outer IP header
   and another set for the inner IP header), then it is more natural to
   model them as two different instances of classifier LFB, as shown in
   Figure 8.b.




Halpern & Hadi Salim         Standards Track                   [Page 36]


RFC 5812                     ForCES FE Model                  March 2010


3.4.2.   Configuring the LFB Topology

   While there is little doubt that an individual LFB must be
   configurable, the configurability question is more complicated for
   LFB topology.  Since the LFB topology is really the graphic
   representation of the data paths within an FE, configuring the LFB
   topology means dynamically changing the data paths, including
   changing the LFBs along the data paths on an FE (e.g., creating/
   instantiating, updating, or deleting LFBs) and setting up or deleting
   interconnections between outputs of upstream LFBs to inputs of
   downstream LFBs.

   Why would the data paths on an FE ever change dynamically?  The data
   paths on an FE are set up by the CE to provide certain data plane
   services (e.g., Diffserv, VPN) to the network element's (NE)
   customers.  The purpose of reconfiguring the data paths is to enable
   the CE to customize the services the NE is delivering at run time.
   The CE needs to change the data paths when the service requirements
   change, such as adding a new customer or when an existing customer
   changes their service.  However, note that not all data path changes
   result in changes in the LFB topology graph.  Changes in the graph
   are dependent on the approach used to map the data paths into LFB
   topology.  As discussed in Section 3.4.1, the topological approach
   and encoded state approach can result in very different looking LFB
   topologies for the same data paths.  In general, an LFB topology
   based on a pure topological approach is likely to experience more
   frequent topology reconfiguration than one based on an encoded state
   approach.  However, even an LFB topology based entirely on an encoded
   state approach may have to change the topology at times, for example,
   to bypass some LFBs or insert new LFBs.  Since a mix of these two
   approaches is used to model the data paths, LFB topology
   reconfiguration is considered an important aspect of the FE model.

   We want to point out that allowing a configurable LFB topology in the
   FE model does not mandate that all FEs are required to have this
   capability.  Even if an FE supports configurable LFB topology, the FE
   may impose limitations on what can actually be configured.
   Performance-optimized hardware implementations may have zero or very
   limited configurability, while FE implementations running on network
   processors may provide more flexibility and configurability.  It is
   entirely up to the FE designers to decide whether or not the FE
   actually implements reconfiguration and if so, how much.  Whether a
   simple runtime switch is used to enable or disable (i.e., bypass)
   certain LFBs, or more flexible software reconfiguration is used, is
   an implementation detail internal to the FE and outside the scope of
   the FE model.  In either case, the CE(s) MUST be able to learn the
   FE's configuration capabilities.  Therefore, the FE model MUST




Halpern & Hadi Salim         Standards Track                   [Page 37]


RFC 5812                     ForCES FE Model                  March 2010


   provide a mechanism for describing the LFB topology configuration
   capabilities of an FE.  These capabilities may include (see Section 5
   for full details):

   o  Which LFB classes the FE can instantiate

   o  The maximum number of instances of the same LFB class that can be
      created

   o  Any topological limitations, for example:

      *  The maximum number of instances of the same class or any class
         that can be created on any given branch of the graph

      *  Ordering restrictions on LFBs (e.g., any instance of LFB class
         A must be always downstream of any instance of LFB class B)

   The CE needs some programming help in order to cope with the range of
   complexity.  In other words, even when the CE is allowed to configure
   LFB topology for the FE, the CE is not expected to be able to
   interpret an arbitrary LFB topology and determine which specific
   service or application (e.g., VPN, Diffserv) is supported by the FE.
   However, once the CE understands the coarse capability of an FE, the
   CE MUST configure the LFB topology to implement the network service
   the NE is supposed to provide.  Thus, the mapping the CE has to
   understand is from the high-level NE service to a specific LFB
   topology, not the other way around.  The CE is not expected to have
   the ultimate intelligence to translate any high-level service policy
   into the configuration data for the FEs.  However, it is conceivable
   that within a given network service domain, a certain amount of
   intelligence can be programmed into the CE to give the CE a general
   understanding of the LFBs involved to allow the translation from a
   high-level service policy to the low-level FE configuration to be
   done automatically.  Note that this is considered an implementation
   issue internal to the control plane and outside the scope of the FE
   model.  Therefore, it is not discussed any further in this document.















Halpern & Hadi Salim         Standards Track                   [Page 38]


RFC 5812                     ForCES FE Model                  March 2010


         +----------+     +-----------+
    ---->| Ingress  |---->|classifier |--------------+
         |          |     |chip       |              |
         +----------+     +-----------+              |
                                                     v
                         +-------------------------------------------+
           +--------+    |   Network Processor                       |
      <----| Egress |    |   +------+    +------+   +-------+        |
           +--------+    |   |Meter |    |Marker|   |Dropper|        |
                 ^       |   +------+    +------+   +-------+        |
                 |       |                                           |
      +----------+-------+                                           |
      |          |                                                   |
      |    +---------+       +---------+   +------+    +---------+   |
      |    |Forwarder|<------|Scheduler|<--|Queue |    |Counter  |   |
      |    +---------+       +---------+   +------+    +---------+   |
      +--------------------------------------------------------------+

         Figure 9: The capability of an FE as reported to the CE.

   Figure 9 shows an example where a QoS-enabled (quality-of-service)
   router has several line cards that have a few ingress ports and
   egress ports, a specialized classification chip, and a network
   processor containing codes for FE blocks like meter, marker, dropper,
   counter, queue, scheduler, and IPv4 forwarder.  Some of the LFB
   topology is already fixed and has to remain static due to the
   physical layout of the line cards.  For example, all of the ingress
   ports might be hardwired into the classification chip so all packets
   flow from the ingress port into the classification engine.  On the
   other hand, the LFBs on the network processor and their execution
   order are programmable.  However, certain capacity limits and linkage
   constraints could exist between these LFBs.  Examples of the capacity
   limits might be:

   o  8 meters

   o  16 queues in one FE

   o  the scheduler can handle at most up to 16 queues

   o  The linkage constraints might dictate that:

      *  the classification engine may be followed by:

         +  a meter

         +  marker




Halpern & Hadi Salim         Standards Track                   [Page 39]


RFC 5812                     ForCES FE Model                  March 2010


         +  dropper

         +  counter

         +  queue or IPv4 forwarder, but not a scheduler

      *  queues can only be followed by a scheduler

      *  a scheduler must be followed by the IPv4 forwarder

      *  the last LFB in the data path before going into the egress
         ports must be the IPv4 forwarder

           +-----+    +-------+                      +---+
           |    A|--->|Queue1 |--------------------->|   |
    ------>|     |    +-------+                      |   |  +---+
           |     |                                   |   |  |   |
           |     |    +-------+      +-------+       |   |  |   |
           |    B|--->|Meter1 |----->|Queue2 |------>|   |->|   |
           |     |    |       |      +-------+       |   |  |   |
           |     |    |       |--+                   |   |  |   |
           +-----+    +-------+  |   +-------+       |   |  +---+
         classifier              +-->|Dropper|       |   |  IPv4
                                     +-------+       +---+  Fwd.
                                                  Scheduler

                 Figure 10: An LFB topology as configured
                     by the CE and accepted by the FE.

   Once the FE reports these capabilities and capacity limits to the CE,
   it is now up to the CE to translate the QoS policy into a desirable
   configuration for the FE.  Figure 9 depicts the FE capability, while
   Figure 10 and Figure 11 depict two different topologies that the CE
   may request the FE to configure.  Note that Figure 11 is not fully
   drawn, as inter-LFB links are included to suggest potential
   complexity, without drawing in the endpoints of all such links.















Halpern & Hadi Salim         Standards Track                   [Page 40]


RFC 5812                     ForCES FE Model                  March 2010


                                             Queue1
                     +---+                    +--+
                     |  A|------------------->|  |--+
                  +->|   |                    |  |  |
                  |  |  B|--+  +--+   +--+    +--+  |
                  |  +---+  |  |  |   |  |          |
                  | Meter1  +->|  |-->|  |          |
                  |            |  |   |  |          |
                  |            +--+   +--+          |          IPv4
                  |         Counter1 Dropper1 Queue2|    +--+  Fwd.
          +---+   |                           +--+  +--->|A |  +-+
          |  A|---+                           |  |------>|B |  | |
   ------>|  B|------------------------------>|  |   +-->|C |->| |->
          |  C|---+                           +--+   | +>|D |  | |
          |  D|-+ |                                  | | +--+  +-+
          +---+ | |    +---+                  Queue3 | |Scheduler
      Classifier1 | |  |  A|------------>       +--+ | |
                  | +->|   |                    |  |-+ |
                  |    |  B|--+  +--+ +-------->|  |   |
                  |    +---+  |  |  | |         +--+   |
                  |  Meter2   +->|  |-+                |
                  |              |  |                  |
                  |              +--+           Queue4 |
                  |            Marker1          +--+   |
                  +---------------------------->|  |---+
                                                |  |
                                                +--+

               Figure 11: Another LFB topology as configured
                     by the CE and accepted by the FE.

   Note that both the ingress and egress are omitted in Figure 10 and
   Figure 11 to simplify the representation.  The topology in Figure 11
   is considerably more complex than Figure 10, but both are feasible
   within the FE capabilities, and so the FE should accept either
   configuration request from the CE.

4.   Model and Schema for LFB Classes

   The main goal of the FE model is to provide an abstract, generic,
   modular, implementation-independent representation of the FEs.  This
   is facilitated using the concept of LFBs, which are instantiated from
   LFB classes.  LFB classes and associated definitions will be provided








Halpern & Hadi Salim         Standards Track                   [Page 41]


RFC 5812                     ForCES FE Model                  March 2010


   in a collection of XML documents.  The collection of these XML
   documents is called an LFB class library, and each document is called
   an LFB class library document (or library document, for short).  Each
   of the library documents MUST conform to the schema presented in this
   section.  The schema here and the rules for conforming to the schema
   are those defined by the W3C in the definitions of XML schema in XML
   schema [Schema1] and XML schema DataTypes [Schema2].  The root
   element of the library document is the <LFBLibrary> element.

   It is not expected that library documents will be exchanged between
   FEs and CEs "over-the-wire".  But the model will serve as an
   important reference for the design and development of the CEs
   (software) and FEs (mostly the software part).  It will also serve as
   a design input when specifying the ForCES protocol elements for CE-FE
   communication.

   The following sections describe the portions of an LFBLibrary XML
   document.  The descriptions primarily provide the necessary semantic
   information to understand the meaning and uses of the XML elements.
   The XML schema below provides the final definition on what elements
   are permitted, and their base syntax.  Unfortunately, due to the
   limitations of English and XML, there are constraints described in
   the semantic sections that are not fully captured in the XML schema,
   so both sets of information need to be used to build a compliant
   library document.

4.1.  Namespace

   A namespace is needed to uniquely identify the LFB type in the LFB
   class library.  The reference to the namespace definition is
   contained in Section 9, IANA Considerations.

4.2.  <LFBLibrary> Element

   The <LFBLibrary> element serves as a root element of all library
   documents.  A library document contains a sequence of top-level
   elements.  The following is a list of all the elements that can occur
   directly in the <LFBLibrary> element.  If they occur, they must occur
   in the order listed.

   o  <description> providing a text description of the purpose of the
      library document,

   o  <load> for loading information from other library documents,

   o  <frameDefs> for the frame declarations,





Halpern & Hadi Salim         Standards Track                   [Page 42]


RFC 5812                     ForCES FE Model                  March 2010


   o  <dataTypeDefs> for defining common data types,

   o  <metadataDefs> for defining metadata, and

   o  <LFBClassDefs> for defining LFB classes.

   Each element is optional.  One library document may contain only
   metadata definitions, another may contain only LFB class definitions,
   and yet another may contain all of the above.

   A library document can import other library documents if it needs to
   refer to definitions contained in the included document.  This
   concept is similar to the "#include" directive in the C programming
   language.  Importing is expressed by the use of <load> elements,
   which must precede all the above elements in the document.  For
   unique referencing, each LFBLibrary instance document has a unique
   label defined in the "provide" attribute of the LFBLibrary element.
   Note that what this performs is a ForCES inclusion, not an XML
   inclusion.  The semantic content of the library referenced by the
   <load> element is included, not the xml content.  Also, in terms of
   the conceptual processing of <load> elements, the total set of
   documents loaded is considered to form a single document for
   processing.  A given document is included in this set only once, even
   if it is referenced by <load> elements several times, even from
   several different files.  As the processing of LFBLibrary information
   is not order dependent, the order for processing loaded elements is
   up to the implementor, as long as the total effect is as if all of
   the information from all the files were available for referencing
   when needed.  Note that such computer processing of ForCES model
   library documents may be helpful for various implementations, but is
   not required to define the libraries, or for the actual operation of
   the protocol itself.

   The following is a skeleton of a library document:

















Halpern & Hadi Salim         Standards Track                   [Page 43]


RFC 5812                     ForCES FE Model                  March 2010


       <?xml version="1.0" encoding="UTF-8"?>
       <LFBLibrary xmlns="urn:ietf:params:xml:ns:forces:lfbmodel:1.0"
         provides="this_library">

         <description>

         </description>

         <!-- Loading external libraries (optional) -->
         <load library="another_library"/>
          ...

         <!-- FRAME TYPE DEFINITIONS (optional) -->
         <frameDefs>
          ...
         </frameDefs>

         <!-- DATA TYPE DEFINITIONS (optional) -->
         <dataTypeDefs>
          ...
         </dataTypeDefs>

         <!-- METADATA DEFINITIONS (optional) -->
         <metadataDefs>
          ...
         </metadataDefs>

         <!--
           -
           -
            LFB CLASS DEFINITIONS (optional) -->
         <LFBCLassDefs>

         </LFBCLassDefs>
         </LFBLibrary>

4.3.  <load> Element

   This element is used to refer to another LFB library document.
   Similar to the "#include" directive in C, this makes the objects
   (metadata types, data types, etc.) defined in the referred library
   document available for referencing in the current document.

   The load element MUST contain the label of the library document to be
   included and MAY contain a URL to specify where the library can be
   retrieved.  The load element can be repeated unlimited times.  Below
   are three examples for the <load> elements:




Halpern & Hadi Salim         Standards Track                   [Page 44]


RFC 5812                     ForCES FE Model                  March 2010


   <load library="a_library"/>
   <load library="another_library" location="another_lib.xml"/>
   <load library="yetanother_library"
    location="http://www.example.com/forces/1.0/lfbmodel/lpm.xml"/>

4.4.  <frameDefs> Element for Frame Type Declarations

   Frame names are used in the LFB definition to define the types of
   frames the LFB expects at its input port(s) and emits at its output
   port(s).  The <frameDefs> optional element in the library document
   contains one or more <frameDef> elements, each declaring one frame
   type.

   Each frame definition MUST contain a unique name (NMTOKEN) and a
   brief synopsis.  In addition, an optional detailed description MAY be
   provided.

   Uniqueness of frame types MUST be ensured among frame types defined
   in the same library document and in all directly or indirectly
   included library documents.

   The following example defines two frame types:

   <frameDefs>
     <frameDef>
      <name>ipv4</name>
      <synopsis>IPv4 packet</synopsis>
      <description>
       This frame type refers to an IPv4 packet.
     </description>
    </frameDef>
     <frameDef>
     <name>ipv6</name>
     <synopsis>IPv6 packet</synopsis>
     <description>
       This frame type refers to an IPv6 packet.
     </description>
    </frameDef>
     ...
   </frameDefs>

4.5.  <dataTypeDefs> Element for Data Type Definitions

   The (optional) <dataTypeDefs> element can be used to define commonly
   used data types.  It contains one or more <dataTypeDef> elements,
   each defining a data type with a unique name.  Such data types can be
   used in several places in the library documents, including:




Halpern & Hadi Salim         Standards Track                   [Page 45]


RFC 5812                     ForCES FE Model                  March 2010


   o  Defining other data types

   o  Defining components of LFB classes

   This is similar to the concept of having a common header file for
   shared data types.

   Each <dataTypeDef> element MUST contain a unique name (NMTOKEN), a
   brief synopsis, and a type definition element.  The name MUST be
   unique among all data types defined in the same library document and
   in any directly or indirectly included library documents.  The
   <dataTypeDef> element MAY also include an optional longer
   description, for example:

   <dataTypeDefs>
     <dataTypeDef>
       <name>ieeemacaddr</name>
        <synopsis>48-bit IEEE MAC address</synopsis>
         ... type definition ...
     </dataTypeDef>
     <dataTypeDef>
       <name>ipv4addr</name>
        <synopsis>IPv4 address</synopsis>
        ... type definition ...
     </dataTypeDef>
     ...
   </dataTypeDefs>

   There are two kinds of data types: atomic and compound.  Atomic data
   types are appropriate for single-value variables (e.g., integer,
   string, byte array).

   The following built-in atomic data types are provided, but additional
   atomic data types can be defined with the <typeRef> and <atomic>
   elements:
















Halpern & Hadi Salim         Standards Track                   [Page 46]


RFC 5812                     ForCES FE Model                  March 2010


          <name>                   Meaning
          ----                     -------
          char                     8-bit signed integer
          uchar                    8-bit unsigned integer
          int16                    16-bit signed integer
          uint16                   16-bit unsigned integer
          int32                    32-bit signed integer
          uint32                   32-bit unsigned integer
          int64                    64-bit signed integer
          uint64                   64-bit unsigned integer
          boolean                  A true / false value where
                                   0 = false, 1 = true
          string[N]                A UTF-8 string represented in at most
                                   N octets
          string                   A UTF-8 string without a configured
                                   storage length limit
          byte[N]                  A byte array of N bytes
          octetstring[N]           A buffer of N octets, which MAY
                                   contain fewer than N octets.  Hence
                                   the encoded value will always have
                                   a length.
          float32                  32-bit IEEE floating point number
          float64                  64-bit IEEE floating point number

   These built-in data types can be readily used to define metadata or
   LFB attributes, but can also be used as building blocks when defining
   new data types.  The boolean data type is defined here because it is
   so common, even though it can be built by sub-ranging the uchar data
   type, as defined under atomic types (Section 4.5.2).

   Compound data types can build on atomic data types and other compound
   data types.  Compound data types can be defined in one of four ways.
   They may be defined as an array of components of some compound or
   atomic data type.  They may be a structure of named components of
   compound or atomic data types (cf. C structures).  They may be a
   union of named components of compound or atomic data types (cf. C
   unions).  They may also be defined as augmentations (explained in
   Section 4.5.7) of existing compound data types.

   Given that the ForCES protocol will be getting and setting component
   values, all atomic data types used here must be able to be conveyed
   in the ForCES protocol.  Further, the ForCES protocol will need a
   mechanism to convey compound data types.  However, the details of
   such representations are for the ForCES protocol [RFC5810] document
   to define, not the model document.  Strings and octetstrings must be
   conveyed by the protocol with their length, as they are not
   delimited, the value does not itself include the length, and these
   items are variable length.



Halpern & Hadi Salim         Standards Track                   [Page 47]


RFC 5812                     ForCES FE Model                  March 2010


   With regard to strings, this model defines a small set of
   restrictions and definitions on how they are structured.  String and
   octetstring length limits can be specified in the LFB class
   definitions.  The component properties for string and octetstring
   components also contain actual lengths and length limits.  This
   duplication of limits is to allow for implementations with smaller
   limits than the maximum limits specified in the LFB class definition.
   In all cases, these lengths are specified in octets, not in
   characters.  In terms of protocol operation, as long as the specified
   length is within the FE's supported capabilities, the FE stores the
   contents of a string exactly as provided by the CE, and returns those
   contents when requested.  No canonicalization, transformations, or
   equivalences are performed by the FE.  Components of type string (or
   string[n]) MAY be used to hold identifiers for correlation with
   components in other LFBs.  In such cases, an exact octet for octet
   match is used.  No equivalences are used by the FE or CE in
   performing that matching.  The ForCES protocol [RFC5810] does not
   perform or require validation of the content of UTF-8 strings.
   However, UTF-8 strings SHOULD be encoded in the shortest form to
   avoid potential security issues described in [UNICODE].  Any entity
   displaying such strings is expected to perform its own validation
   (for example, for correct multi-byte characters, and for ensuring
   that the string does not end in the middle of a multi-byte sequence).
   Specific LFB class definitions MAY restrict the valid contents of a
   string as suited to the particular usage (for example, a component
   that holds a DNS name would be restricted to hold only octets valid
   in such a name).  FEs should validate the contents of SET requests
   for such restricted components at the time the set is performed, just
   as range checks for range-limited components are performed.  The
   ForCES protocol behavior defines the normative processing for
   requests using that protocol.

   For the definition of the actual type in the <dataTypeDef> element,
   the following elements are available: <typeRef>, <atomic>, <array>,
   <struct>, and <union>.

   The predefined type alias is somewhere between the atomic and
   compound data types.  Alias is used to allow a component inside an
   LFB to be an indirect reference to another component inside the same
   or a different LFB class or instance.  The alias component behaves
   like a structure, one component of which has special behavior.  Given
   that the special behavior is tied to the other parts of the
   structure, the compound result is treated as a predefined construct.








Halpern & Hadi Salim         Standards Track                   [Page 48]


RFC 5812                     ForCES FE Model                  March 2010


4.5.1.  <typeRef> Element for Renaming Existing Data Types

   The <typeRef> element refers to an existing data type by its name.
   The referred data type MUST be defined either in the same library
   document or in one of the included library documents.  If the
   referred data type is an atomic data type, the newly defined type
   will also be regarded as atomic.  If the referred data type is a
   compound type, the new type will also be compound.  Some usage
   examples follow:

   <dataTypeDef>
     <name>short</name>
     <synopsis>Alias to int16</synopsis>
     <typeRef>int16</typeRef>
   </dataTypeDef>
   <dataTypeDef>
     <name>ieeemacaddr</name>
     <synopsis>48-bit IEEE MAC address</synopsis>
     <typeRef>byte[6]</typeRef>
   </dataTypeDef>

4.5.2.  <atomic> Element for Deriving New Atomic Types

   The <atomic> element allows the definition of a new atomic type from
   an existing atomic type, applying range restrictions and/or providing
   special enumerated values.  Note that the <atomic> element can only
   use atomic types as base types, and its result MUST be another atomic
   type.

   For example, the following snippet defines a new "dscp" data type:

   <dataTypeDef>
     <name>dscp</name>
     <synopsis>Diffserv code point.</synopsis>
     <atomic>
       <baseType>uchar</baseType>
       <rangeRestriction>
         <allowedRange min="0" max="63"/>
       </rangeRestriction>
       <specialValues>
         <specialValue value="0">
           <name>DSCP-BE</name>
           <synopsis>Best Effort</synopsis>
         </specialValue>
          ...
       </specialValues>
     </atomic>
    </dataTypeDef>



Halpern & Hadi Salim         Standards Track                   [Page 49]


RFC 5812                     ForCES FE Model                  March 2010


4.5.3.  <array> Element to Define Arrays

   The <array> element can be used to create a new compound data type as
   an array of a compound or an atomic data type.  Depending upon
   context, this document and others refer to such arrays as tables or
   arrays interchangeably, without semantic or syntactic implication.
   The type of the array entry can be specified either by referring to
   an existing type (using the <typeRef> element) or defining an unnamed
   type inside the <array> element using any of the <atomic>, <array>,
   <struct>, or <union> elements.

   The array can be "fixed-size" or "variable-size", which is specified
   by the "type" attribute of the <array> element.  The default is
   "variable-size".  For variable-size arrays, an optional "maxlength"
   attribute specifies the maximum allowed length.  This attribute
   should be used to encode semantic limitations, not implementation
   limitations.  The latter (support for implementation constraints)
   should be handled by capability components of LFB classes, and should
   never be included as the maxlength in a data type array that is
   regarded as being of unlimited size.

   For fixed-size arrays, a "length" attribute MUST be provided that
   specifies the constant size of the array.

   The result of this construct is always a compound type, even if the
   array has a fixed size of 1.

   Arrays MUST only be subscripted by integers, and will be presumed to
   start with index 0.

   In addition to their subscripts, arrays MAY be declared to have
   content keys.  Such a declaration has several effects:

   o  Any declared key can be used in the ForCES protocol to select a
      component for operations (for details, see the ForCES protocol
      [RFC5810]).

   o  In any instance of the array, each declared key MUST be unique
      within that instance.  That is, no two components of an array may
      have the same values on all the fields that make up a key.

   Each key is declared with a keyID for use in the ForCES protocol
   [RFC5810], where the unique key is formed by combining one or more
   specified key fields.  To support the case where an array of an
   atomic type with unique values can be referenced by those values, the
   key field identifier MAY be "*" (i.e., the array entry is the key).
   If the value type of the array is a structure or an array, then the
   key is one or more components of the value type, each identified by



Halpern & Hadi Salim         Standards Track                   [Page 50]


RFC 5812                     ForCES FE Model                  March 2010


   name.  Since the field MAY be a component of the contained structure,
   a component of a component of a structure, or further nested, the
   field name is actually a concatenated sequence of component
   identifiers, separated by decimal points (".").  The syntax for key
   field identification is given following the array examples.

   The following example shows the definition of a fixed-size array with
   a predefined data type as the array content type:

     <dataTypeDef>
           <name>dscp-mapping-table</name>
           <synopsis>
              A table of 64 DSCP values, used to re-map code space.
           </synopsis>
           <array type="fixed-size" length="64">
              <typeRef>dscp</typeRef>
           </array>
         </dataTypeDef>

   The following example defines a variable-size array with an upper
   limit on its size:

         <dataTypeDef>
           <name>mac-alias-table</name>
           <synopsis>A table with up to 8 IEEE MAC addresses</synopsis>
           <array type="variable-size" maxlength="8">
               <typeRef>ieeemacaddr</typeRef>
           </array>
         </dataTypeDef>






















Halpern & Hadi Salim         Standards Track                   [Page 51]


RFC 5812                     ForCES FE Model                  March 2010


   The following example shows the definition of an array with a local
   (unnamed) content type definition:

         <dataTypeDef>
           <name>classification-table</name>
           <synopsis>
             A table of classification rules and result opcodes.
           </synopsis>
           <array type="variable-size">
             <struct>
               <component componentID="1">
                 <name>rule</name>
                 <synopsis>The rule to match</synopsis>
                 <typeRef>classrule</typeRef>
               </component>
               <component componentID="2">
                 <name>opcode</name>
                 <synopsis>The result code</synopsis>
                 <typeRef>opcode</typeRef>
               </component>
            </struct>
           </array>
         </dataTypeDef>

   In the above example, each entry of the array is a <struct> of two
   components ("rule" and "opcode").

   The following example shows a table of IP prefix information that can
   be accessed by a multi-field content key on the IP address, prefix
   length, and information source.  This means that in any instance of
   this table, no two entries can have the same IP address, prefix
   length, and information source.



















Halpern & Hadi Salim         Standards Track                   [Page 52]


RFC 5812                     ForCES FE Model                  March 2010


      <dataTypeDef>
        <name>ipPrefixInfo_table</name>
        <synopsis>
          A table of information about known prefixes
        </synopsis>
        <array type="variable-size">
          <struct>
            <component componentID="1">
              <name>address-prefix</name>
              <synopsis>the prefix being described</synopsis>
              <typeRef>ipv4Prefix</typeRef>
            </component>
            <component componentID="2">
              <name>source</name>
              <synopsis>
                  the protocol or process providing this information
              </synopsis>
              <typeRef>uint16</typeRef>
            </component>
            <component componentID="3">
              <name>prefInfo</name>
              <synopsis>the information we care about</synopsis>
              <typeRef>hypothetical-info-type</typeRef>
            </component>
          </struct>
          <contentKey contentKeyID="1">
            <contentKeyField> address-prefix.ipv4addr</contentKeyField>
            <contentKeyField> address-prefix.prefixlen</contentKeyField>
            <contentKeyField> source</contentKeyField>
          </contentKey>
        </array>
      </dataTypeDef>

   Note that the keyField elements could also have been simply address-
   prefix and source, since all of the fields of address-prefix are
   being used.















Halpern & Hadi Salim         Standards Track                   [Page 53]


RFC 5812                     ForCES FE Model                  March 2010


4.5.3.1.  Key Field References

   In order to use key declarations, one must refer to components that
   are potentially nested inside other components in the array.  If
   there are nested arrays, one might even use an array element as a key
   (but great care would be needed to ensure uniqueness).

   The key is the combination of the values of each field declared in a
   keyField element.

   Therefore, the value of a keyField element MUST be a concatenated
   sequence of field identifiers, separated by a "." (period) character.
   Whitespace is permitted and ignored.

   A valid string for a single field identifier within a keyField
   depends upon the current context.  Initially, in an array key
   declaration, the context is the type of the array.  Progressively,
   the context is whatever type is selected by the field identifiers
   processed so far in the current key field declaration.

   When the current context is an array (e.g., when declaring a key for
   an array whose content is an array), then the only valid value for
   the field identifier is an explicit number.

   When the current context is a structure, the valid values for the
   field identifiers are the names of the components of the structure.
   In the special case of declaring a key for an array containing an
   atomic type, where that content is unique and is to be used as a key,
   the value "*" MUST be used as the single key field identifier.

   In reference array or structure elements, it is possible to construct
   keyFields that do not exist. keyField references SHOULD never
   reference optional structure components.  For references to array
   elements, care must be taken to ensure that the necessary array
   elements exist when creating or modifying the overall array element.
   Failure to do so will result in FEs returning errors on the creation
   attempt.

4.5.4.  <struct> Element to Define Structures

   A structure is composed of a collection of data components.  Each
   data component has a data type (either an atomic type or an existing
   compound type) and is assigned a name unique within the scope of the
   compound data type being defined.  These serve the same function as
   "struct" in C, etc.  These components are defined using <component>
   elements.  A <struct> element MAY contain an optional derivation
   indication, a <derivedFrom> element.  The structure definition MUST
   contain a sequence of one or more <component> elements.



Halpern & Hadi Salim         Standards Track                   [Page 54]


RFC 5812                     ForCES FE Model                  March 2010


   The actual type of the component can be defined by referring to an
   existing type (using the <typeRef> element), or can be a locally
   defined (unnamed) type created by any of the <atomic>, <array>,
   <struct>, or <union> elements.

   The <component> element MUST include a componentID attribute.  This
   provides the numeric ID for this component, for use by the protocol.
   The <component> MUST contain a component name and a synopsis.  It MAY
   contain a <description> element giving a textual description of the
   component.  The definition MAY also include an <optional> element,
   which indicates that the component being defined is optional.  The
   definition MUST contain elements to define the data type of the
   component, as described above.

   For a dataTypeDef of a struct, the structure definition MAY be
   inherited from, and augment, a previously defined structured type.
   This is indicated by including the optional derivedFrom attribute in
   the struct declaration before the definition of the augmenting or
   replacing components.  Section 4.5.7 describes how this is done in
   more detail.

   The componentID attribute for different components in a structure (or
   in an LFB) MUST be distinct.  They do not need to be in order, nor do
   they need to be sequential.  For clarity of human readability, and
   ease of maintenance, it is usual to define at least sequential sets
   of values.  But this is for human ease, not a model or protocol
   requirement.

   The result of this construct is always a compound type, even when the
   <struct> contains only one field.





















Halpern & Hadi Salim         Standards Track                   [Page 55]


RFC 5812                     ForCES FE Model                  March 2010


   An example is the following:

   <dataTypeDef>
    <name>ipv4prefix</name>
    <synopsis>
     IPv4 prefix defined by an address and a prefix length
    </synopsis>
    <struct>
     <component componentID="1">
      <name>address</name>
      <synopsis>Address part</synopsis>
      <typeRef>ipv4addr</typeRef>
     </component>
     <component componentID="2">
      <name>prefixlen</name>
      <synopsis>Prefix length part</synopsis>
      <atomic>
       <baseType>uchar</baseType>
       <rangeRestriction>
        <allowedRange min="0" max="32"/>
       </rangeRestriction>
      </atomic>
     </component>
    </struct>
   </dataTypeDef>

4.5.5.  <union> Element to Define Union Types

   Similar to the union declaration in C, this construct allows the
   definition of overlay types.  Its format is identical to the <struct>
   element.

   The result of this construct is always a compound type, even when the
   union contains only one element.

4.5.6.  <alias> Element

   It is sometimes necessary to have a component in an LFB or structure
   refer to information (a component) in other LFBs.  This can, for
   example, allow an ARP LFB to share the IP->MAC Address table with the
   local transmission LFB, without duplicating information.  Similarly,
   it could allow a traffic measurement LFB to share information with a
   traffic enforcement LFB.  The <alias> declaration creates the
   constructs for this.  This construct tells the CE and FE that any
   manipulation of the defined data is actually manipulation of data






Halpern & Hadi Salim         Standards Track                   [Page 56]


RFC 5812                     ForCES FE Model                  March 2010


   defined to exist in some specified part of some other LFB instance.
   The content of an <alias> element MUST be a named type.  Whatever
   component the alias references (which is determined by the alias
   component properties, as described below), that component must be of
   the same type as that declared for the alias.  Thus, when the CE or
   FE dereferences the alias component, the type of the information
   returned is known.  The type can be a base type or a derived type.
   The actual value referenced by an alias is known as its target.  When
   a GET or SET operation references the alias element, the value of the
   target is returned or replaced.  Write access to an alias element is
   permitted if write access to both the alias and the target is
   permitted.

   The target of a component declared by an <alias> element is
   determined by the information in the component's properties.  Like
   all components, the properties include the support / read / write
   permission for the alias.  In addition, there are several fields
   (components) in the alias properties that define the target of the
   alias.  These components are the ID of the LFB class of the target,
   the ID of the LFB instance of the target, and a sequence of integers
   representing the path within the target LFB instance to the target
   component.  The type of the target element must match the declared
   type of the alias.  Details of the alias property structure are
   described in Section 4.8 of this document, on properties.

   Note that the read / write property of the alias refers to the value.
   The CE can only determine if it can write the target selection
   properties of the alias by attempting such a write operation.
   (Property components do not themselves have properties.)

4.5.7.  Augmentations

   Compound types can also be defined as augmentations of existing
   compound types.  If the existing compound type is a structure,
   augmentation MAY add new elements to the type.  The type of an
   existing component MAY be replaced in the definition of an augmenting
   structure, but MAY only be replaced with an augmentation derived from
   the current type of the existing component.  An existing component
   cannot be deleted.  If the existing compound type is an array,
   augmentation means augmentation of the array element type.

   Augmentation MUST NOT be applied to unions.

   One consequence of this is that augmentations are backward compatible
   with the compound type from which they are derived.  As such,
   augmentations are useful in defining components for LFB subclasses
   with backward compatibility.  In addition to adding new components to
   a class, the data type of an existing component MAY be replaced by an



Halpern & Hadi Salim         Standards Track                   [Page 57]


RFC 5812                     ForCES FE Model                  March 2010


   augmentation of that component, and still meet the compatibility
   rules for subclasses.  This compatibility constraint is why
   augmentations cannot be applied to unions.

   For example, consider a simple base LFB class A that has only one
   component (comp1) of type X.  One way to derive class A1 from A can
   be by simply adding a second component (of any type).  Another way to
   derive a class A2 from A can be by replacing the original component
   (comp1) in A of type X with one of type Y, where Y is an augmentation
   of X.  Both classes A1 and A2 are backward compatible with class A.

   The syntax for augmentations is to include a <derivedFrom> element in
   a structure definition, indicating what structure type is being
   augmented.  Component names and component IDs for new components
   within the augmentation MUST NOT be the same as those in the
   structure type being augmented.  For those components where the data
   type of an existing component is being replaced with a suitable
   augmenting data type, the existing component name and component ID
   MUST be used in the augmentation.  Other than the constraint on
   existing elements, there is no requirement that the new component IDs
   be sequential with, greater than, or in any other specific
   relationship to the existing component IDs except different.  It is
   expected that using values sequential within an augmentation, and
   distinct from the previously used values, will be a common method to
   enhance human readability.

4.6.   <metadataDefs> Element for Metadata Definitions

   The (optional) <metadataDefs> element in the library document
   contains one or more <metadataDef> elements.  Each <metadataDef>
   element defines a metadatum.

   Each <metadataDef> element MUST contain a unique name (NMTOKEN).
   Uniqueness is defined to be over all metadata defined in this library
   document and in all directly or indirectly included library
   documents.  The <metadataDef> element MUST also contain a brief
   synopsis, the tag value to be used for this metadata, and value type
   definition information.  Only atomic data types can be used as value
   types for metadata.  The <metadataDef> element MAY contain a detailed
   description element.

   Two forms of type definitions are allowed.  The first form uses the
   <typeRef> element to refer to an existing atomic data type defined in
   the <dataTypeDefs> element of the same library document or in one of
   the included library documents.  The usage of the <typeRef> element
   is identical to how it is used in the <dataTypeDef> elements, except
   here it can only refer to atomic types.  The latter restriction is
   not enforced by the XML schema.



Halpern & Hadi Salim         Standards Track                   [Page 58]


RFC 5812                     ForCES FE Model                  March 2010


   The second form is an explicit type definition using the <atomic>
   element.  This element is used here in the same way as in the
   <dataTypeDef> elements.

   The following example shows both usages:

   <metadataDefs>
    <metadataDef>
     <name>NEXTHOPID</name>
     <synopsis>Refers to a Next Hop entry in NH LFB</synopsis>
     <metadataID>17</metadataID>
     <typeRef>int32</typeRef>
    </metadataDef>
    <metadataDef>
     <name>CLASSID</name>
     <synopsis>
      Result of classification (0 means no match).
     </synopsis>
     <metadataID>21</metadataID>
     <atomic>
      <baseType>int32</baseType>
      <specialValues>
       <specialValue value="0">
        <name>NOMATCH</name>
        <synopsis>
         Classification didn't result in match.
        </synopsis>
       </specialValue>
      </specialValues>
     </atomic>
    </metadataDef>
   </metadataDefs>

4.7.  <LFBClassDefs> Element for LFB Class Definitions

   The (optional) <LFBClassDefs> element can be used to define one or
   more LFB classes using <LFBClassDef> elements.  Each <LFBClassDef>
   element MUST define an LFB class and include the following elements:

   o  <name> provides the symbolic name of the LFB class.  Example:
      "ipv4lpm".

   o  <synopsis> provides a short synopsis of the LFB class.  Example:
      "IPv4 Longest Prefix Match Lookup LFB".

   o  <version> is the version indicator.





Halpern & Hadi Salim         Standards Track                   [Page 59]


RFC 5812                     ForCES FE Model                  March 2010


   o  <derivedFrom> is the inheritance indicator.

   o  <inputPorts> lists the input ports and their specifications.

   o  <outputPorts> lists the output ports and their specifications.

   o  <components> defines the operational components of the LFB.

   o  <capabilities> defines the capability components of the LFB.

   o  <description> contains the operational specification of the LFB.

   o  The LFBClassID attribute of the LFBClassDef element defines the ID
      for this class.  These must be globally unique.

   o  <events> defines the events that can be generated by instances of
      this LFB.

   LFB class names must be unique, in order to enable other documents to
   reference the classes by name, and to enable human readers to
   understand references to class names.  While a complex naming
   structure could be created, simplicity is preferred.  As given in the
   IANA Considerations section of this document, the IANA maintains a
   registry of LFB class names and class identifiers, along with a
   reference to the document defining the class.

   Below is a skeleton of an example LFB class definition.  Note that in
   order to keep from complicating the XML schema, the order of elements
   in the class definition is fixed.  Elements, if they appear, must
   appear in the order shown.





















Halpern & Hadi Salim         Standards Track                   [Page 60]


RFC 5812                     ForCES FE Model                  March 2010


   <LFBClassDefs>
    <LFBClassDef LFBClassID="12345">
     <name>ipv4lpm</name>
     <synopsis>IPv4 Longest Prefix Match Lookup LFB</synopsis>
     <version>1.0</version>
     <derivedFrom>baseclass</derivedFrom>

     <inputPorts>
      ...
     </inputPorts>

     <outputPorts>
      ...
     </outputPorts>

     <components>
      ...
     </components>

     <capabilities>
      ...
     </capabilities>

     <events>
      ...
     </events>

     <description>
      This LFB represents the IPv4 longest prefix match lookup
      operation.
      The modeled behavior is as follows:
      Blah-blah-blah.
     </description>

    </LFBClassDef>
    ...
   </LFBClassDefs>

   The individual components and capabilities will have componentIDs for
   use by the ForCES protocol.  These parallel the componentIDs used in
   structs, and are used the same way.  Component and capability
   componentIDs must be unique within the LFB class definition.

   Note that the <name>, <synopsis>, and <version> elements are
   required; all other elements are optional in <LFBClassDef>.  However,
   when they are present, they must occur in the above order.





Halpern & Hadi Salim         Standards Track                   [Page 61]


RFC 5812                     ForCES FE Model                  March 2010


   The componentID attribute for different items in an LFB class
   definition (or components in a struct) MUST be distinct.  They do not
   need to be in order, nor do they need to be sequential.  For clarity
   of human readability, and ease of maintenance, it is usual to define
   at least sequential sets of values.  But this is for human ease, not
   a model or protocol requirement.

4.7.1.  <derivedFrom> Element to Express LFB Inheritance

   The optional <derivedFrom> element can be used to indicate that this
   class is a derivative of some other class.  The content of this
   element MUST be the unique name (<name>) of another LFB class.  The
   referred LFB class MUST be defined in the same library document or in
   one of the included library documents.  In the absence of a
   <derivedFrom>, the class is conceptually derived from the common,
   empty, base class.

   It is assumed that a derived class is backward compatible with its
   base class.  A derived class MAY add components to a parent class,
   but cannot delete components.  This also applies to input and output
   ports, events, and capabilities.

4.7.2.  <inputPorts> Element to Define LFB Inputs

   The optional <inputPorts> element is used to define input ports.  An
   LFB class MAY have zero, one, or more inputs.  If the LFB class has
   no input ports, the <inputPorts> element MUST be omitted.  The
   <inputPorts> element can contain one or more <inputPort> elements,
   one for each port or port group.  We assume that most LFBs will have
   exactly one input.  Multiple inputs with the same input type are
   modeled as one input group.  Input groups are defined the same way as
   input ports by the <inputPort> element, differentiated only by an
   optional "group" attribute.

   Multiple inputs with different input types should be avoided if
   possible (see discussion in Section 4.7.3).  Some special LFBs will
   have no inputs at all.  For example, a packet generator LFB does not
   need an input.

   Single input ports and input port groups are both defined by the
   <inputPort> element; they are differentiated only by an optional
   "group" attribute.

   The <inputPort> element MUST contain the following elements:

   o  <name> provides the symbolic name of the input.  Example: "in".
      Note that this symbolic name must be unique only within the scope
      of the LFB class.



Halpern & Hadi Salim         Standards Track                   [Page 62]


RFC 5812                     ForCES FE Model                  March 2010


   o  <synopsis> contains a brief description of the input.  Example:
      "Normal packet input".

   o  <expectation> lists all allowed frame formats.  Example: {"ipv4"
      and "ipv6"}.  Note that this list should refer to names specified
      in the <frameDefs> element of the same library document or in any
      included library documents.  The <expectation> element can also
      provide a list of required metadata.  Example: {"classid",
      "vpnid"}.  This list should refer to names of metadata defined in
      the <metadataDefs> element in the same library document or in any
      included library documents.  For each metadatum, it must be
      specified whether the metadatum is required or optional.  For each
      optional metadatum, a default value must be specified, which is
      used by the LFB if the metadatum is not provided with a packet.

   In addition, the optional "group" attribute of the <inputPort>
   element can specify if the port can behave as a port group, i.e., it
   is allowed to be instantiated.  This is indicated by a "true" value
   (the default value is "false").

   An example <inputPorts> element, defining two input ports, the second
   one being an input port group is the following:

   <inputPorts>
    <inputPort>
     <name>in</name>
     <synopsis>Normal input</synopsis>
     <expectation>
      <frameExpected>
       <ref>ipv4</ref>
       <ref>ipv6</ref>
      </frameExpected>
      <metadataExpected>
       <ref>classid</ref>
       <ref>vifid</ref>
       <ref dependency="optional" defaultValue="0">vrfid</ref>
      </metadataExpected>
     </expectation>
    </inputPort>
    <inputPort group="true">
     ... another input port ...
    </inputPort>
   </inputPorts>

   For each <inputPort>, the frame type expectations are defined by the
   <frameExpected> element using one or more <ref> elements (see example
   above).  When multiple frame types are listed, it means that "one of
   these" frame types is expected.  A packet of any other frame type is



Halpern & Hadi Salim         Standards Track                   [Page 63]


RFC 5812                     ForCES FE Model                  March 2010


   regarded as incompatible with this input port of the LFB class.  The
   above example lists two frames as expected frame types: "ipv4" and
   "ipv6".

   Metadata expectations are specified by the <metadataExpected>
   element.  In its simplest form, this element can contain a list of
   <ref> elements, each referring to a metadatum.  When multiple
   instances of metadata are listed by <ref> elements, it means that
   "all of these" metadata must be received with each packet (except
   metadata that are marked as "optional" by the "dependency" attribute
   of the corresponding <ref> element).  For a metadatum that is
   specified "optional", a default value MUST be provided using the
   "defaultValue" attribute.  The above example lists three metadata as
   expected metadata, two of which are mandatory ("classid" and
   "vifid"), and one being optional ("vrfid").

   The schema also allows for more complex definitions of metadata
   expectations.  For example, using the <one-of> element, a list of
   metadata can be specified to express that at least one of the
   specified metadata must be present with any packet.  An example is
   the following:

   <metadataExpected>
    <one-of>
     <ref>prefixmask</ref>
     <ref>prefixlen</ref>
    </one-of>
   </metadataExpected>

   The above example specifies that either the "prefixmask" or the
   "prefixlen" metadata must be provided with any packet.

   The two forms can also be combined, as shown in the following
   example:

   <metadataExpected>
    <ref>classid</ref>
    <ref>vifid</ref>
    <ref dependency="optional" defaultValue="0">vrfid</ref>
    <one-of>
     <ref>prefixmask</ref>
     <ref>prefixlen</ref>
    </one-of>
   </metadataExpected>

   Although the schema is constructed to allow even more complex
   definitions of metadata expectations, we do not discuss those here.




Halpern & Hadi Salim         Standards Track                   [Page 64]


RFC 5812                     ForCES FE Model                  March 2010


4.7.3.  <outputPorts> Element to Define LFB Outputs

   The optional <outputPorts> element is used to define output ports.
   An LFB class MAY have zero, one, or more outputs.  If the LFB class
   has no output ports, the <outputPorts> element MUST be omitted.  The
   <outputPorts> element MUST contain one or more <outputPort> elements,
   one for each port or port group.  If there are multiple outputs with
   the same output type, we model them as an output port group.  Some
   special LFBs have no outputs at all (e.g., Dropper).

   Single output ports and output port groups are both defined by the
   <outputPort> element; they are differentiated only by an optional
   "group" attribute.

   The <outputPort> element MUST contain the following elements:

   o  <name> provides the symbolic name of the output.  Example: "out".
      Note that the symbolic name must be unique only within the scope
      of the LFB class.

   o  <synopsis> contains a brief description of the output port.
      Example: "Normal packet output".

   o  <product> lists the allowed frame formats.  Example: {"ipv4",
      "ipv6"}.  Note that this list should refer to symbols specified in
      the <frameDefs> element in the same library document or in any
      included library documents.  The <product> element MAY also
      contain the list of emitted (generated) metadata.  Example:
      {"classid", "color"}.  This list should refer to names of metadata
      specified in the <metadataDefs> element in the same library
      document or in any included library documents.  For each generated
      metadatum, it should be specified whether the metadatum is always
      generated or generated only in certain conditions.  This
      information is important when assessing compatibility between
      LFBs.

   In addition, the optional "group" attribute of the <outputPort>
   element can specify if the port can behave as a port group, i.e., it
   is allowed to be instantiated.  This is indicated by a "true" value
   (the default value is "false").

   The following example specifies two output ports, the second being an
   output port group:








Halpern & Hadi Salim         Standards Track                   [Page 65]


RFC 5812                     ForCES FE Model                  March 2010


   <outputPorts>
    <outputPort>
     <name>out</name>
     <synopsis>Normal output</synopsis>
     <product>
      <frameProduced>
       <ref>ipv4</ref>
       <ref>ipv4bis</ref>
      </frameProduced>
      <metadataProduced>
       <ref>nhid</ref>
       <ref>nhtabid</ref>
      </metadataProduced>
     </product>
    </outputPort>
    <outputPort group="true">
     <name>exc</name>
     <synopsis>Exception output port group</synopsis>
     <product>
      <frameProduced>
       <ref>ipv4</ref>
       <ref>ipv4bis</ref>
      </frameProduced>
      <metadataProduced>
       <ref availability="conditional">errorid</ref>
      </metadataProduced>
     </product>
    </outputPort>
   </outputPorts>

   The types of frames and metadata the port produces are defined inside
   the <product> element in each <outputPort>.  Within the <product>
   element, the list of frame types the port produces is listed in the
   <frameProduced> element.  When more than one frame is listed, it
   means that "one of" these frames will be produced.

   The list of metadata that is produced with each packet is listed in
   the optional <metadataProduced> element of the <product>.  In its
   simplest form, this element can contain a list of <ref> elements,
   each referring to a metadatum type.  The meaning of such a list is
   that "all of" these metadata are provided with each packet, except
   those that are listed with the optional "availability" attribute set
   to "conditional".  Similar to the <metadataExpected> element of the
   <inputPort>, the <metadataProduced> element supports more complex
   forms, which we do not discuss here further.






Halpern & Hadi Salim         Standards Track                   [Page 66]


RFC 5812                     ForCES FE Model                  March 2010


4.7.4.  <components> Element to Define LFB Operational Components

   Operational parameters of the LFBs that must be visible to the CEs
   are conceptualized in the model as the LFB components.  These
   include, for example, flags, single parameter arguments, complex
   arguments, and tables.  Note that the components here refer to only
   those operational parameters of the LFBs that must be visible to the
   CEs.  Other variables that are internal to LFB implementation are not
   regarded as LFB components and hence are not covered.

   Some examples for LFB components are:

   o  Configurable flags and switches selecting between operational
      modes of the LFB

   o  Number of inputs or outputs in a port group

   o  Various configurable lookup tables, including interface tables,
      prefix tables, classification tables, DSCP mapping tables, MAC
      address tables, etc.

   o  Packet and byte counters

   o  Various event counters

   o  Number of current inputs or outputs for each input or output group

   The ForCES model supports the definition of access permission
   restrictions on what the CE can do with an LFB component.  The
   following categories are supported by the model:

   o  No-access components.  This is useful for completeness, and to
      allow for defining objects that are used by other things, but not
      directly referencable by the CE.  It is also useful for an FE that
      is reporting that certain defined, and typically accessible,
      components are not supported for CE access by a reporting FE.

   o  Read-only components.

   o  Read-write components.

   o  Write-only components.  This could be any configurable data for
      which read capability is not provided to the CEs (e.g., the
      security key information).

   o  Read-reset components.  The CE can read and reset this resource,
      but cannot set it to an arbitrary value.  Example: Counters.




Halpern & Hadi Salim         Standards Track                   [Page 67]


RFC 5812                     ForCES FE Model                  March 2010


   o  Firing-only components.  A write attempt to this resource will
      trigger some specific actions in the LFB, but the actual value
      written is ignored.

   The LFB class MUST define only one possible access mode for a given
   component.

   The components of the LFB class are listed in the <components>
   element.  Each component is defined by an <component> element.  A
   <component> element contains some or all of the following elements,
   some of which are mandatory:

   o  <name> MUST occur, and defines the name of the component.  This
      name must be unique among the components of the LFB class.
      Example: "version".

   o  <synopsis> is also mandatory, and provides a brief description of
      the purpose of the component.

   o  <optional/> is an optional element, and if present indicates that
      this component is optional.

   o  The data type of the component can be defined either via a
      reference to a predefined data type or by providing a local
      definition of the type.  The former is provided by using the
      <typeRef> element, which must refer to the unique name of an
      existing data type defined in the <dataTypeDefs> element in the
      same library document or in any of the included library documents.
      When the data type is defined locally (unnamed type), one of the
      following elements can be used: <atomic>, <array>, <struct>, or
      <union>.  Their usage is identical to how they are used inside
      <dataTypeDef> elements (see Section 4.5).  Some form of data type
      definition MUST be included in the component definition.

   o  The <defaultValue> element is optional, and if present is used to
      specify a default value for a component.  If a default value is
      specified, the FE must ensure that the component has that value
      when the LFB is initialized or reset.  If a default value is not
      specified for a component, the CE MUST make no assumptions as to
      what the value of the component will be upon initialization.  The
      CE must either read the value or set the value, if it needs to
      know what it is.

   o  The <description> element MAY also appear.  If included, it
      provides a longer description of the meaning or usage of the
      particular component being defined.





Halpern & Hadi Salim         Standards Track                   [Page 68]


RFC 5812                     ForCES FE Model                  March 2010


   The <component> element also MUST have a componentID attribute, which
   is a numeric value used by the ForCES protocol.

   In addition to the above elements, the <component> element includes
   an optional "access" attribute, which can take any of the following
   values: "read-only", "read-write", "write-only", "read-reset", and
   "trigger-only".  The default access mode is "read-write".

   Whether optional components are supported, and whether components
   defined as read-write can actually be written, can be determined for
   a given LFB instance by the CE by reading the property information of
   that component.  An access control setting of "trigger-only" means
   that this component is included only for use in event detection.

   The following example defines two components for an LFB:

   <components>
    <component access="read-only" componentID="1">
     <name>foo</name>
     <synopsis>number of things</synopsis>
     <typeRef>uint32</typeRef>
    </component>
    <component access="read-write" componentID="2">
     <name>bar</name>
     <synopsis>number of this other thing</synopsis>
     <atomic>
      <baseType>uint32</baseType>
      <rangeRestriction>
       <allowedRange min="10" max="2000"/>
      </rangeRestriction>
     </atomic>
     <defaultValue>10</defaultValue>
    </component>
   </components>

   The first component ("foo") is a read-only 32-bit unsigned integer,
   defined by referring to the built-in "uint32" atomic type.  The
   second component ("bar") is also an integer, but uses the <atomic>
   element to provide additional range restrictions.  This component has
   access mode of read-write allowing it to be both read and written.  A
   default value of 10 is provided for bar.  Although the access for bar
   is read-write, some implementations MAY offer only more restrictive
   access, and this would be reported in the component properties.








Halpern & Hadi Salim         Standards Track                   [Page 69]


RFC 5812                     ForCES FE Model                  March 2010


   Note that not all components are likely to exist at all times in a
   particular implementation.  While the capabilities will frequently
   indicate this non-existence, CEs may attempt to reference non-
   existent or non-permitted components anyway.  The ForCES protocol
   mechanisms should include appropriate error indicators for this case.

   The mechanism defined above for non-supported components can also
   apply to attempts to reference non-existent array elements or to set
   read-only components.

4.7.5.  <capabilities> Element to Define LFB Capability Components

   The LFB class specification provides some flexibility for the FE
   implementation regarding how the LFB class is implemented.  For
   example, the instance may have some limitations that are not inherent
   from the class definition, but rather the result of some
   implementation limitations.  Some of these limitations are captured
   by the property information of the LFB components.  The model allows
   for the notion of additional capability information.

   Such capability-related information is expressed by the capability
   components of the LFB class.  The capability components are always
   read-only attributes, and they are listed in a separate
   <capabilities> element in the <LFBClassDef>.  The <capabilities>
   element contains one or more <capability> elements, each defining one
   capability component.  The format of the <capability> element is
   almost the same as the <component> element.  It differs in two
   aspects: it lacks the access mode attribute (because it is always
   read-only), and it lacks the <defaultValue> element (because default
   value is not applicable to read-only attributes).

   Some examples of capability components follow:

   o  The version of the LFB class with which this LFB instance complies

   o  Supported optional features of the LFB class

   o  Maximum number of configurable outputs for an output group

   o  Metadata pass-through limitations of the LFB

   o  Additional range restriction on operational components









Halpern & Hadi Salim         Standards Track                   [Page 70]


RFC 5812                     ForCES FE Model                  March 2010


   The following example lists two capability attributes:

   <capabilities>
    <capability componentID="3">
     <name>version</name>
     <synopsis>
      LFB class version this instance is compliant with.
     </synopsis>
     <typeRef>version</typeRef>
    </capability>
    <capability componentID="4">
     <name>limitBar</name>
     <synopsis>
      Maximum value of the "bar" attribute.
     </synopsis>
     <typeRef>uint16</typeRef>
    </capability>
   </capabilities>

4.7.6.  <events> Element for LFB Notification Generation

   The <events> element contains the information about the occurrences
   for which instances of this LFB class can generate notifications to
   the CE.  High-level view on the declaration and operation of LFB
   events is described in Section 3.2.5.

   The <events> element contains 0 or more <event> elements, each of
   which declares a single event.  The <event> element has an eventID
   attribute giving the unique (per LFB class) ID of the event.  The
   element will include:

   o  <eventTarget> element indicating which LFB field (component) is
      tested to generate the event.

   o  <condition> element indicating what condition on the field will
      generate the event from a list of defined conditions.

   o  <eventReports> element indicating what values are to be reported
      in the notification of the event.

   The example below demonstrates the different constructs.

   The <events> element has a baseID attribute value, which is normally
   <events baseID="number">.  The value of the baseID is the starting
   componentID for the path that identifies events.  It must not be the
   same as the componentID of any top-level components (including
   capabilities) of the LFB class.  In derived LFBs (i.e., ones with a
   <derivedFrom> element) where the parent LFB class has an events



Halpern & Hadi Salim         Standards Track                   [Page 71]


RFC 5812                     ForCES FE Model                  March 2010


   declaration, the baseID must not be present in the derived LFB
   <events> element.  Instead, the baseID value from the parent LFB
   class is used.  In the example shown, the baseID is 7.

   <events baseID="7">
    <event eventID="7">
      <name>Foochanged</name>
      <synopsis>
          An example event for a scalar
      </synopsis>
      <eventTarget>
        <eventField>foo</eventField>
      </eventTarget>
      <eventChanged/>
      <eventReports>
        <!-- report the new state -->
        <eventReport>
          <eventField>foo</eventField>
        </eventReport>
      </eventReports>
    </event>

    <event eventID="8">
      <name>Goof1changed</name>
      <synopsis>
          An example event for a complex structure
      </synopsis>
      <eventTarget>
        <!-- target is goo.f1 -->
        <eventField>goo</eventField>
        <eventField>f1</eventField>
      </eventTarget>
      <eventChanged/>
      <eventReports>
        <!-- report the new state of goo.f1 -->
        <eventReport>
        <eventField>goo</eventField>
        <eventField>f1</eventField>
        </eventReport>
      </eventReports>
    </event>










Halpern & Hadi Salim         Standards Track                   [Page 72]


RFC 5812                     ForCES FE Model                  March 2010


    <event eventID="9">
      <name>NewbarEntry</name>
      <synopsis>
          Event for a new entry created on table bar
      </synopsis>
      <eventTarget>
        <eventField>bar</eventField>
        <eventSubscript>_barIndex_</eventSubscript>
      </eventTarget>
      <eventCreated/>
      <eventReports>
        <eventReport>
         <eventField>bar</eventField>
         <eventSubscript>_barIndex_</eventSubscript>
       </eventReport>
       <eventReport>
        <eventField>foo</eventField>
       </eventReport>
      </eventReports>
    </event>

    <event eventID="10">
      <name>Gah11changed</name>
      <synopsis>
          Event for table gah, entry index 11 changing
      </synopsis>
      <eventTarget>
        <eventField>gah</eventField>
        <eventSubscript>11</eventSubscript>
      </eventTarget>
      <eventChanged/>
      <eventReports>
        <eventReport>
         <eventField>gah</eventField>
         <eventSubscript>11</eventSubscript>
       </eventReport>
      </eventReports>
    </event>













Halpern & Hadi Salim         Standards Track                   [Page 73]


RFC 5812                     ForCES FE Model                  March 2010


    <event eventID="11">
      <name>Gah10field1</name>
      <synopsis>
          Event for table gah, entry index 10, column field1 changing
      </synopsis>
      <eventTarget>
        <eventField>gah</eventField>
        <eventSubscript>10</eventSubscript>
        <eventField>field1</eventField>
      </eventTarget>
      <eventChanged/>
      <eventReports>
        <eventReport>
         <eventField>gah</eventField>
         <eventSubscript>10</eventSubscript>
        </eventReport>
      </eventReports>
    </event>
   </events>

4.7.6.1.  <eventTarget> Element

   The <eventTarget> element contains information identifying a field in
   the LFB that is to be monitored for events.

   The <eventTarget> element contains one or more <eventField>s each of
   which MAY be followed by one or more <eventSubscript> elements.  Each
   of these two elements represents the textual equivalent of a path
   select component of the LFB.

   The <eventField> element contains the name of a component in the LFB
   or a component nested in an array or structure within the LFB.  The
   name used in <eventField> MUST identify a valid component within the
   containing LFB context.  The first element in an <eventTarget> MUST
   be an <eventField> element.  In the example shown, four LFB
   components foo, goo, bar, and gah are used as <eventField>s.

   In the simple case, an <eventField> identifies an atomic component.
   This is the case illustrated in the event named Foochanged.
   <eventField> is also used to address complex components such as
   arrays or structures.

      The first defined event, Foochanged, demonstrates how a scalar LFB
      component, foo, could be monitored to trigger an event.

      The second event, Goof1changed, demonstrates how a member of the
      complex structure goo could be monitored to trigger an event.




Halpern & Hadi Salim         Standards Track                   [Page 74]


RFC 5812                     ForCES FE Model                  March 2010


      The events named NewbarEntry, Gah11changed, and Gah10field1
      represent monitoring of arrays bar and gah in differing details.

   If an <eventField> identifies a complex component, then a further
   <eventField> MAY be used to refine the path to the target element.
   Defined event Goof1changed demonstrates how a second <eventField> is
   used to point to member f1 of the structure goo.

   If an <eventField> identifies an array, then the following rules
   apply:

   o  <eventSubscript> elements MUST be present as the next XML element
      after an <eventField> that identifies an array component.
      <eventSubscript> MUST NOT occur other than after an array
      reference, as it is only meaningful in that context.

   o  An <eventSubscript> contains either:

      *  A numeric value to indicate that the event applies to a
         specific entry (by index) of the array.  As an example, event
         Gah11changed shows how table gah's index 11 is being targeted
         for monitoring.

   Or

      *  It is expected that the more common usage is to have the event
         being defined across all elements of the array (i.e., a
         wildcard for all indices).  In that case, the value of the
         <eventSubscript> MUST be a name rather than a numeric value.
         That same name can then be used as the value of
         <eventSubscript> in <eventReport> elements as described below.
         An example of a wild card table index is shown in event
         NewBarentry where the <eventSubscript> value is named
         _barIndex_

   o  An <eventField> MAY follow an <eventSubscript> to further refine
      the path to the target element.  (Note: this is in the same spirit
      as the case where <eventField> is used to further refine
      <eventField> in the earlier example of a complex structure example
      of Goof1changed.)  The example event Gah10field1 illustrates how
      the column field1 of table gah is monitored for changes.

   It should be emphasized that the name in an <eventSubscript> element
   in defined event NewbarEntry is not a component name.  It is a
   variable name for use in the <eventReport> elements (described in
   Section 4.7.6.3) of the given LFB definition.  This name MUST be
   distinct from any component name that can validly occur in the
   <eventReport> clause.



Halpern & Hadi Salim         Standards Track                   [Page 75]


RFC 5812                     ForCES FE Model                  March 2010


4.7.6.2.  <eventCondition> Element

   The event condition element represents a condition that triggers a
   notification.  The list of conditions is:

   <eventCreated/>:  The target must be an array, ending with a
                     subscript indication.  The event is generated when
                     an entry in the array is created.  This occurs even
                     if the entry is created by CE direction.  The event
                     example NewbarEntry demonstrates the
                     <eventCreated/> condition.

   <eventDeleted/>:  The target must be an array, ending with a
                     subscript indication.  The event is generated when
                     an entry in the array is destroyed.  This occurs
                     even if the entry is destroyed by CE direction.

   <eventChanged/>:  The event is generated whenever the target
                     component changes in any way.  For binary
                     components such as up/down, this reflects a change
                     in state.  It can also be used with numeric
                     attributes, in which case any change in value
                     results in a detected trigger.  Event examples
                     Foochanged, Gah11changed, and Gah10field1
                     illustrate the <eventChanged/> condition.

   <eventGreaterThan/>:  The event is generated whenever the target
                         component becomes greater than the threshold.
                         The threshold is an event property.

   <eventLessThan/>:  The event is generated whenever the target
                      component becomes less than the threshold.  The
                      threshold is an event property.

4.7.6.3.  <eventReports> Element

   The <eventReports> element of an <event> declares the information to
   be delivered by the FE along with the notification of the occurrence
   of the event.

   The <eventReports> element contains one or more <eventReport>
   elements.  Each <eventReport> element identifies a piece of data from
   the LFB class to be reported.  The notification carries that data as
   if the collection of <eventReport> elements had been defined in a
   structure.  The syntax is exactly the same as used in the
   <eventTarget> element, using <eventField> and <eventSubscript>
   elements, and so the same rules apply.  Each <eventReport> element
   thus MUST identify a component in the LFB class. <eventSubcript> MAY



Halpern & Hadi Salim         Standards Track                   [Page 76]


RFC 5812                     ForCES FE Model                  March 2010


   contain integers.  If they contain names, they MUST be names from
   <eventSubscript> elements of the <eventTarget> in the event.  The
   selection for the report will use the value for the subscript that
   identifies that specific element triggering the event.  This can be
   used to reference the component causing the event, or to reference
   related information in parallel tables.

   In the example shown, in the case of the event Foochanged, the report
   will carry the value of foo.  In the case of the defined event
   NewbarEntry acting on LFB component bar, which is an array, there are
   two items that are reported as indicated by the two <eventReport>
   declarations:

   o  The first <eventReport> details what new entry was added in the
      table bar.  Recall that _barIndex_ is declared as the event's
      <eventTarget> <eventSubcript> and that by virtue of using a name
      instead of a numeric value, the <eventSubcript> is implied to be a
      wildcard and will carry whatever index of the new entry.

   o  The second <eventReport> includes the value of LFB component foo
      at the time the new entry was created in bar.  Reporting foo in
      this case is provided to demonstrate the flexibility of event
      reporting.

   This event reporting structure is designed to allow the LFB designer
   to specify information that is likely not known a priori by the CE
   and is likely needed by the CE to process the event.  While the
   structure allows for pointing at large blocks of information (full
   arrays or complex structures), this is not recommended.  Also, the
   variable reference/subscripting in reporting only captures a small
   portion of the kinds of related information.  Chaining through index
   fields stored in a table, for example, is not supported.  In general,
   the <eventReports> mechanism is an optimization for cases that have
   been found to be common, saving the CE from having to query for
   information it needs to understand the event.  It does not represent
   all possible information needs.

   If any components referenced by the eventReport are optional, then
   the report MUST use a protocol format that supports optional elements
   and allows for the non-existence of such elements.  Any components
   that do not exist are not reported.

4.7.6.4.  Runtime Control of Events

   The high-level view of the declaration and operation of LFB events is
   described in Section 3.2.5.





Halpern & Hadi Salim         Standards Track                   [Page 77]


RFC 5812                     ForCES FE Model                  March 2010


   The <eventTarget> provides additional components used in the path to
   reference the event.  The path constitutes the baseID for events,
   followed by the ID for the specific event, followed by a value for
   each <eventSubscript> element if it exists in the <eventTarget>.

   The event path will uniquely identify a specific occurrence of the
   event in the event notification to the CE.  In the example provided
   above, at the end of Section 4.7.6, a notification with path of 7.7
   uniquely identifies the event to be that caused by the change of foo;
   an event with path 7.9.100 uniquely identifies the event to be that
   caused by a creation of table bar entry with index/subscript 100.

   As described in Section 4.8.5, event elements have properties
   associated with them.  These properties include the subscription
   information indicating whether the CE wishes the FE to generate event
   reports for the event at all, thresholds for events related to level
   crossing, and filtering conditions that may reduce the set of event
   notifications generated by the FE.  Details of the filtering
   conditions that can be applied are given in that section.  The
   filtering conditions allow the FE to suppress floods of events that
   could result from oscillation around a condition value.  For FEs that
   do not wish to support filtering, the filter properties can be either
   read-only or not supported.

   In addition to identifying the event sources, the CE also uses the
   event path to activate runtime control of the event via the event
   properties (defined in Section 4.8.5) utilizing SET-PROP as defined
   in the ForCES protocol [RFC5810] operation.

   To activate event generation on the FE, a SET-PROP message
   referencing the event and registration property of the event is
   issued to the FE by the CE with any prefix of the path of the event.
   So, for an event defined on the example table bar, a SET-PROP with a
   path of 7.9 will subscribe the CE to all occurrences of that event on
   any entry of the table.  This is particularly useful for the
   <eventCreated/> and <eventDestroyed/> conditions on tables.  Events
   using those conditions will generally be defined with a field/
   subscript sequence that identifies an array and ends with an
   <eventSubscript> element.  Thus, the event notification will indicate
   which array entry has been created or destroyed.  A typical
   subscriber will subscribe for the array, as opposed to a specific
   entry in an array, so it will use a shorter path.

   In the example provided, subscribing to 7.8 implies receiving all
   declared events from table bar.  Subscribing to 7.8.100 implies
   receiving an event when subscript/index 100 table entry is created.





Halpern & Hadi Salim         Standards Track                   [Page 78]


RFC 5812                     ForCES FE Model                  March 2010


   Threshold and filtering conditions can only be applied to individual
   events.  For events defined on elements of an array, this
   specification does not allow for defining a threshold or filtering
   condition on an event for all elements of an array.

4.7.7.  <description> Element for LFB Operational Specification

   The <description> element of the <LFBClass> provides unstructured
   text (in XML sense) to explain what the LFB does to a human user.

4.8.  Properties

   Components of LFBs have properties that are important to the CE.  The
   most important property is the existence / readability / writeability
   of the element.  Depending on the type of the component, other
   information may be of importance.

   The model provides the definition of the structure of property
   information.  There is a base class of property information.  For the
   array, alias, and event components, there are subclasses of property
   information providing additional fields.  This information is
   accessed by the CE (and updated where applicable) via the ForCES
   protocol.  While some property information is writeable, there is no
   mechanism currently provided for checking the properties of a
   property element.  Writeability can only be checked by attempting to
   modify the value.

4.8.1.  Basic Properties

   The basic property definition, along with the scalar dataTypeDef for
   accessibility, is below.  Note that this access permission
   information is generally read-only.



















Halpern & Hadi Salim         Standards Track                   [Page 79]


RFC 5812                     ForCES FE Model                  March 2010


                <dataTypeDef>
                  <name>accessPermissionValues</name>
                  <synopsis>
                    The possible values of component access permission
                  </synopsis>
                  <atomic>
                    <baseType>uchar</baseType>
                    <specialValues>
                      <specialValue value="0">
                        <name>None</name>
                        <synopsis>Access is prohibited</synopsis>
                      </specialValue>
                       <specialValue value="1">
                        <name> Read-Only </name>
                        <synopsis>
                          Access to the component is read only
                        </synopsis>
                      </specialValue>
                      <specialValue value="2">
                        <name>Write-Only</name>
                        <synopsis>
                          The component MAY be written, but not read
                        </synopsis>
                      </specialValue>
                      <specialValue value="3">
                        <name>Read-Write</name>
                        <synopsis>
                          The component MAY be read or written
                        </synopsis>
                      </specialValue>
                    </specialValues>
                  </atomic>
                </dataTypeDef>
                <dataTypeDef>
                  <name>baseElementProperties</name>
                  <synopsis>basic properties, accessibility</synopsis>
                  <struct>
                    <component componentID="1">
                      <name>accessibility</name>
                      <synopsis>
                          does the component exist, and
                          can it be read or written
                      </synopsis>
                      <typeRef>accessPermissionValues</typeRef>
                    </component>
                  </struct>
                </dataTypeDef>




Halpern & Hadi Salim         Standards Track                   [Page 80]


RFC 5812                     ForCES FE Model                  March 2010


4.8.2.  Array Properties

   The properties for an array add a number of important pieces of
   information.  These properties are also read-only.

         <dataTypeDef>
           <name>arrayElementProperties</name>
           <synopsis>Array Element Properties definition</synopsis>
           <struct>
             <derivedFrom>baseElementProperties</derivedFrom>
             <component componentID="2">
               <name>entryCount</name>
               <synopsis>the number of entries in the array</synopsis>
               <typeRef>uint32</typeRef>
             </component>
             <component componentID="3">
               <name>highestUsedSubscript</name>
               <synopsis>the last used subscript in the array</synopsis>
               <typeRef>uint32</typeRef>
             </component>
             <component componentID="4">
               <name>firstUnusedSubscript</name>
               <synopsis>
                 The subscript of the first unused array element
               </synopsis>
               <typeRef>uint32</typeRef>
             </component>
           </struct>
         </dataTypeDef>

4.8.3.  String Properties

   The properties of a string specify the actual octet length and the
   maximum octet length for the element.  The maximum length is included
   because an FE implementation MAY limit a string to be shorter than
   the limit in the LFB class definition.















Halpern & Hadi Salim         Standards Track                   [Page 81]


RFC 5812                     ForCES FE Model                  March 2010


           <dataTypeDef>
             <name>stringElementProperties</name>
             <synopsis>string Element Properties definition </synopsis>
             <struct>
               <derivedFrom>baseElementProperties</derivedFrom>
               <component componentID="2">
                 <name>stringLength</name>
                 <synopsis>the number of octets in the string</synopsis>
                 <typeRef>uint32</typeRef>
               </component>
               <component componentID="3">
                 <name>maxStringLength</name>
                 <synopsis>
                   the maximum number of octets in the string
                   </synopsis>
                 <typeRef>uint32</typeRef>
               </component>
             </struct>
           </dataTypeDef>

4.8.4.  Octetstring Properties

   The properties of an octetstring specify the actual length and the
   maximum length, since the FE implementation MAY limit an octetstring
   to be shorter than the LFB class definition.

              <dataTypeDef>
                <name>octetstringElementProperties</name>
                <synopsis>octetstring Element Properties definition
                </synopsis>
                <struct>
                  <derivedFrom>baseElementProperties</derivedFrom>
                  <component componentID="2">
                    <name>octetstringLength</name>
                    <synopsis>
                      the number of octets in the octetstring
                    </synopsis>
                    <typeRef>uint32</typeRef>
                  </component>
                  <component componentID="3">
                    <name>maxOctetstringLength</name>
                    <synopsis>
                      the maximum number of octets in the octetstring
                    </synopsis>
                    <typeRef>uint32</typeRef>
                  </component>
                </struct>
              </dataTypeDef>



Halpern & Hadi Salim         Standards Track                   [Page 82]


RFC 5812                     ForCES FE Model                  March 2010


4.8.5.  Event Properties

   The properties for an event add three (usually) writeable fields.
   One is the subscription field. 0 means no notification is generated.
   Any non-zero value (typically 1 is used) means that a notification is
   generated.  The hysteresis field is used to suppress generation of
   notifications for oscillations around a condition value, and is
   described below (Section 4.8.5.2).  The threshold field is used for
   the <eventGreaterThan/> and <eventLessThan/> conditions.  It
   indicates the value to compare the event target against.  Using the
   properties allows the CE to set the level of interest.  FEs that do
   not support setting the threshold for events will make this field
   read-only.






































Halpern & Hadi Salim         Standards Track                   [Page 83]


RFC 5812                     ForCES FE Model                  March 2010


            <dataTypeDef>
              <name>eventElementProperties</name>
              <synopsis>event Element Properties definition</synopsis>
              <struct>
                <derivedFrom>baseElementProperties</derivedFrom>
                <component componentID="2">
                  <name>registration</name>
                  <synopsis>
                    has the CE registered to be notified of this event
                  </synopsis>
                  <typeRef>uint32</typeRef>
                </component>
                <component componentID="3">
                  <name>threshold</name>
                  <synopsis> comparison value for level crossing events
                  </synopsis>
                  <optional/>
                  <typeRef>uint32</typeRef>
                </component>
                <component componentID="4">
                  <name>eventHysteresis</name>
                  <synopsis> region to suppress event recurrence notices
                  </synopsis>
                  <optional/>
                  <typeRef>uint32</typeRef>
                </component>
                <component componentID="5">
                  <name>eventCount</name>
                  <synopsis> number of occurrences to suppress
                  </synopsis>
                  <optional/>
                  <typeRef>uint32</typeRef>
                </component>
                <component componentID="6">
                  <name>eventInterval</name>
                  <synopsis> time interval in ms between notifications
                  </synopsis>
                  <optional/>
                  <typeRef>uint32</typeRef>
                </component>
              </struct>
            </dataTypeDef>









Halpern & Hadi Salim         Standards Track                   [Page 84]


RFC 5812                     ForCES FE Model                  March 2010


4.8.5.1.  Common Event Filtering

   The event properties have values for controlling several filter
   conditions.  Support of these conditions is optional, but all
   conditions SHOULD be supported.  Events that are reliably known not
   to be subject to rapid occurrence or other concerns MAY not support
   all filter conditions.

   Currently, three different filter condition variables are defined.
   These are eventCount, eventInterval, and eventHysteresis.  Setting
   the condition variables to 0 (their default value) means that the
   condition is not checked.

   Conceptually, when an event is triggered, all configured conditions
   are checked.  If no filter conditions are triggered, or if any
   trigger conditions are met, the event notification is generated.  If
   there are filter conditions, and no condition is met, then no event
   notification is generated.  Event filter conditions have reset
   behavior when an event notification is generated.  If any condition
   is passed, and the notification is generated, the notification reset
   behavior is performed on all conditions, even those that had not
   passed.  This provides a clean definition of the interaction of the
   various event conditions.

   An example of the interaction of conditions is an event with an
   eventCount property set to 5 and an eventInterval property set to 500
   milliseconds.  Suppose that a burst of occurrences of this event is
   detected by the FE.  The first occurrence will cause a notification
   to be sent to the CE.  Then, if four more occurrences are detected
   rapidly (less than 0.5 seconds) they will not result in
   notifications.  If two more occurrences are detected, then the second
   of those will result in a notification.  Alternatively, if more than
   500 milliseconds has passed since the notification and an occurrence
   is detected, that will result in a notification.  In either case, the
   count and time interval suppression is reset no matter which
   condition actually caused the notification.

4.8.5.2.   Event Hysteresis Filtering

   Events with numeric conditions can have hysteresis filters applied to
   them.  The hysteresis level is defined by a property of the event.
   This allows the FE to notify the CE of the hysteresis applied, and if
   it chooses, the FE can allow the CE to modify the hysteresis.  This
   applies to <eventChanged/> for a numeric field, and to
   <eventGreaterThan/> and <eventLessThan/>.  The content of a






Halpern & Hadi Salim         Standards Track                   [Page 85]


RFC 5812                     ForCES FE Model                  March 2010


   <variance> element is a numeric value.  When supporting hysteresis,
   the FE MUST track the value of the element and make sure that the
   condition has become untrue by at least the hysteresis from the event
   property.  To be specific, if the hysteresis is V, then:

   o  For an <eventChanged/> condition, if the last notification was for
      value X, then the <changed/> notification MUST NOT be generated
      until the value reaches X +/- V.

   o  For an <eventGreaterThan/> condition with threshold T, once the
      event has been generated at least once it MUST NOT be generated
      again until the field first becomes less than or equal to T - V,
      and then exceeds T.

   o  For an <eventLessThan/> condition with threshold T, once the event
      has been generate at least once it MUST NOT be generated again
      until the field first becomes greater than or equal to T + V, and
      then becomes less than T.

4.8.5.3.  Event Count Filtering

   Events MAY have a count filtering condition.  This property, if set
   to a non-zero value, indicates the number of occurrences of the event
   that should be considered redundant and not result in a notification.
   Thus, if this property is set to 1, and no other conditions apply,
   then every other detected occurrence of the event will result in a
   notification.  This particular meaning is chosen so that the value 1
   has a distinct meaning from the value 0.

   A conceptual implementation (not required) for this might be an
   internal suppression counter.  Whenever an event is triggered, the
   counter is checked.  If the counter is 0, a notification is
   generated.  Whether or not a notification is generated, the counter
   is incremented.  If the counter exceeds the configured value, it is
   set to 0.

4.8.5.4.  Event Time Filtering

   Events MAY have a time filtering condition.  This property represents
   the minimum time interval (in the absence of some other filtering
   condition being passed) between generating notifications of detected
   events.  This condition MUST only be passed if the time since the
   last notification of the event is longer than the configured interval
   in milliseconds.







Halpern & Hadi Salim         Standards Track                   [Page 86]


RFC 5812                     ForCES FE Model                  March 2010


   Conceptually, this can be thought of as a stored timestamp that is
   compared with the detection time, or as a timer that is running that
   resets a suppression flag.  In either case, if a notification is
   generated due to passing any condition then the time interval
   detection MUST be restarted.

4.8.6.  Alias Properties

   The properties for an alias add three (usually) writeable fields.
   These combine to identify the target component to which the subject
   alias refers.

          <dataTypeDef>
            <name>aliasElementProperties</name>
            <synopsis>alias Element Properties definition</synopsis>
            <struct>
              <derivedFrom>baseElementProperties</derivedFrom>
              <component componentID="2">
                <name>targetLFBClass</name>
                <synopsis>the class ID of the alias target</synopsis>
                <typeRef>uint32</typeRef>
              </component>
              <component componentID="3">
                <name>targetLFBInstance</name>
                <synopsis>the instance ID of the alias target</synopsis>
                <typeRef>uint32</typeRef>
              </component>
              <component componentID="4">
                <name>targetComponentPath</name>
                <synopsis>
                  the path to the component target
                  each 4 octets is read as one path element,
                  using the path construction in the ForCES protocol,
                  [2].
                </synopsis>
                <typeRef>octetstring[128]</typeRef>
              </component>
            </struct>
          </dataTypeDef>












Halpern & Hadi Salim         Standards Track                   [Page 87]


RFC 5812                     ForCES FE Model                  March 2010


4.9.  XML Schema for LFB Class Library Documents

      <?xml version="1.0" encoding="UTF-8"?>
      <xsd:schema xmlns:xsd="http://www.w3.org/2001/XMLSchema"
       xmlns="urn:ietf:params:xml:ns:forces:lfbmodel:1.0"
       xmlns:lfb="urn:ietf:params:xml:ns:forces:lfbmodel:1.0"
       targetNamespace="urn:ietf:params:xml:ns:forces:lfbmodel:1.0"
       attributeFormDefault="unqualified"
       elementFormDefault="qualified">
      <xsd:annotation>
        <xsd:documentation xml:lang="en">
        Schema for Defining LFB Classes and associated types (frames,
        data types for LFB attributes, and metadata).
        </xsd:documentation>
      </xsd:annotation>
      <xsd:element name="description" type="xsd:string"/>
      <xsd:element name="synopsis" type="xsd:string"/>
      <!-- Document root element: LFBLibrary -->
      <xsd:element name="LFBLibrary">
        <xsd:complexType>
          <xsd:sequence>
            <xsd:element ref="description" minOccurs="0"/>
            <xsd:element name="load" type="loadType" minOccurs="0"
                      maxOccurs="unbounded"/>
         <xsd:element name="frameDefs" type="frameDefsType"
                      minOccurs="0"/>
         <xsd:element name="dataTypeDefs" type="dataTypeDefsType"
                      minOccurs="0"/>
         <xsd:element name="metadataDefs" type="metadataDefsType"
                      minOccurs="0"/>
         <xsd:element name="LFBClassDefs" type="LFBClassDefsType"
                      minOccurs="0"/>
       </xsd:sequence>
       <xsd:attribute name="provides" type="xsd:Name" use="required"/>
     </xsd:complexType>
     <!-- Uniqueness constraints -->
     <xsd:key name="frame">
      <xsd:selector xpath="lfb:frameDefs/lfb:frameDef"/>
       <xsd:field xpath="lfb:name"/>
     </xsd:key>
     <xsd:key name="dataType">
      <xsd:selector xpath="lfb:dataTypeDefs/lfb:dataTypeDef"/>
       <xsd:field xpath="lfb:name"/>
     </xsd:key>
     <xsd:key name="metadataDef">
       <xsd:selector xpath="lfb:metadataDefs/lfb:metadataDef"/>
       <xsd:field xpath="lfb:name"/>
     </xsd:key>



Halpern & Hadi Salim         Standards Track                   [Page 88]


RFC 5812                     ForCES FE Model                  March 2010


     <xsd:key name="LFBClassDef">
       <xsd:selector xpath="lfb:LFBClassDefs/lfb:LFBClassDef"/>
       <xsd:field xpath="lfb:name"/>
     </xsd:key>
   </xsd:element>
   <xsd:complexType name="loadType">
     <xsd:attribute name="library" type="xsd:Name" use="required"/>
     <xsd:attribute name="location" type="xsd:anyURI" use="optional"/>
   </xsd:complexType>
   <xsd:complexType name="frameDefsType">
     <xsd:sequence>
       <xsd:element name="frameDef" maxOccurs="unbounded">
         <xsd:complexType>
        <xsd:sequence>
             <xsd:element name="name" type="xsd:NMTOKEN"/>
             <xsd:element ref="synopsis"/>
             <xsd:element ref="description" minOccurs="0"/>
           </xsd:sequence>
         </xsd:complexType>
       </xsd:element>
     </xsd:sequence>
   </xsd:complexType>
   <xsd:complexType name="dataTypeDefsType">
     <xsd:sequence>
          <xsd:element name="dataTypeDef" maxOccurs="unbounded">
            <xsd:complexType>
              <xsd:sequence>
                <xsd:element name="name" type="xsd:NMTOKEN"/>
                <xsd:element ref="synopsis"/>
                <xsd:element ref="description" minOccurs="0"/>
                <xsd:group ref="typeDeclarationGroup"/>
              </xsd:sequence>
            </xsd:complexType>
          </xsd:element>
        </xsd:sequence>
      </xsd:complexType>
      <!--
         Predefined (built-in) atomic data-types are:
             char, uchar, int16, uint16, int32, uint32, int64, uint64,
             string[N], string, byte[N], boolean, octetstring[N],
             float32, float64
      -->
      <xsd:group name="typeDeclarationGroup">
        <xsd:choice>
          <xsd:element name="typeRef" type="typeRefNMTOKEN"/>
          <xsd:element name="atomic" type="atomicType"/>
          <xsd:element name="array" type="arrayType"/>
          <xsd:element name="struct" type="structType"/>



Halpern & Hadi Salim         Standards Track                   [Page 89]


RFC 5812                     ForCES FE Model                  March 2010


          <xsd:element name="union" type="structType"/>
          <xsd:element name="alias" type="typeRefNMTOKEN"/>
        </xsd:choice>
      </xsd:group>
      <xsd:simpleType name="typeRefNMTOKEN">
        <xsd:restriction base="xsd:token">
          <xsd:pattern value="\c+"/>
          <xsd:pattern value="string\[\d+\]"/>
          <xsd:pattern value="byte\[\d+\]"/>
          <xsd:pattern value="octetstring\[\d+\]"/>
        </xsd:restriction>
      </xsd:simpleType>
      <xsd:complexType name="atomicType">
        <xsd:sequence>
          <xsd:element name="baseType" type="typeRefNMTOKEN"/>
          <xsd:element name="rangeRestriction"
                       type="rangeRestrictionType" minOccurs="0"/>
          <xsd:element name="specialValues" type="specialValuesType"
                       minOccurs="0"/>
        </xsd:sequence>
      </xsd:complexType>
      <xsd:complexType name="rangeRestrictionType">
        <xsd:sequence>
          <xsd:element name="allowedRange" maxOccurs="unbounded">
            <xsd:complexType>
           <xsd:attribute name="min" type="xsd:integer"
   use="required"/>
           <xsd:attribute name="max" type="xsd:integer"
   use="required"/>
         </xsd:complexType>
       </xsd:element>
     </xsd:sequence>
   </xsd:complexType>
   <xsd:complexType name="specialValuesType">
     <xsd:sequence>
       <xsd:element name="specialValue" maxOccurs="unbounded">
         <xsd:complexType>
           <xsd:sequence>
             <xsd:element name="name" type="xsd:NMTOKEN"/>
             <xsd:element ref="synopsis"/>
           </xsd:sequence>
           <xsd:attribute name="value" type="xsd:token"/>
         </xsd:complexType>
       </xsd:element>
     </xsd:sequence>
   </xsd:complexType>
   <xsd:complexType name="arrayType">
     <xsd:sequence>



Halpern & Hadi Salim         Standards Track                   [Page 90]


RFC 5812                     ForCES FE Model                  March 2010


       <xsd:group ref="typeDeclarationGroup"/>
       <xsd:element name="contentKey" minOccurs="0"
                    maxOccurs="unbounded">
         <xsd:complexType>
           <xsd:sequence>
             <xsd:element name="contentKeyField" maxOccurs="unbounded"
                          type="xsd:string"/>
           </xsd:sequence>
           <xsd:attribute name="contentKeyID" use="required"
                          type="xsd:integer"/>
         </xsd:complexType>
         <!--declare keys to have unique IDs -->
         <xsd:key name="contentKeyID">
           <xsd:selector xpath="lfb:contentKey"/>
           <xsd:field xpath="@contentKeyID"/>
         </xsd:key>
       </xsd:element>
     </xsd:sequence>
     <xsd:attribute name="type" use="optional"
                    default="variable-size">
       <xsd:simpleType>
         <xsd:restriction base="xsd:string">
           <xsd:enumeration value="fixed-size"/>
           <xsd:enumeration value="variable-size"/>
         </xsd:restriction>
       </xsd:simpleType>
        </xsd:attribute>
        <xsd:attribute name="length" type="xsd:integer" use="optional"/>
        <xsd:attribute name="maxLength" type="xsd:integer"
                       use="optional"/>
      </xsd:complexType>
      <xsd:complexType name="structType">
        <xsd:sequence>
          <xsd:element name="derivedFrom" type="typeRefNMTOKEN"
                       minOccurs="0"/>
          <xsd:element name="component" maxOccurs="unbounded">
            <xsd:complexType>
              <xsd:sequence>
                <xsd:element name="name" type="xsd:NMTOKEN"/>
                <xsd:element ref="synopsis"/>
                <xsd:element ref="description" minOccurs="0"/>
                <xsd:element name="optional" minOccurs="0"/>
                <xsd:group ref="typeDeclarationGroup"/>
              </xsd:sequence>
              <xsd:attribute name="componentID" use="required"
                             type="xsd:unsignedInt"/>
            </xsd:complexType>
            <!-- key declaration to make componentIDs unique in a struct



Halpern & Hadi Salim         Standards Track                   [Page 91]


RFC 5812                     ForCES FE Model                  March 2010


            -->
            <xsd:key name="structComponentID">
              <xsd:selector xpath="lfb:component"/>
              <xsd:field xpath="@componentID"/>
            </xsd:key>
          </xsd:element>
        </xsd:sequence>
      </xsd:complexType>
      <xsd:complexType name="metadataDefsType">
        <xsd:sequence>
          <xsd:element name="metadataDef" maxOccurs="unbounded">
            <xsd:complexType>
              <xsd:sequence>
                <xsd:element name="name" type="xsd:NMTOKEN"/>
                <xsd:element ref="synopsis"/>
                <xsd:element name="metadataID" type="xsd:integer"/>
                <xsd:element ref="description" minOccurs="0"/>
                <xsd:choice>
                  <xsd:element name="typeRef" type="typeRefNMTOKEN"/>
                  <xsd:element name="atomic" type="atomicType"/>
                </xsd:choice>
              </xsd:sequence>
            </xsd:complexType>
          </xsd:element>
        </xsd:sequence>
      </xsd:complexType>
      <xsd:complexType name="LFBClassDefsType">
        <xsd:sequence>
          <xsd:element name="LFBClassDef" maxOccurs="unbounded">
            <xsd:complexType>
              <xsd:sequence>
                <xsd:element name="name" type="xsd:NMTOKEN"/>
                <xsd:element ref="synopsis"/>
                <xsd:element name="version" type="versionType"/>
                <xsd:element name="derivedFrom" type="xsd:NMTOKEN"
                             minOccurs="0"/>
                <xsd:element name="inputPorts" type="inputPortsType"
                             minOccurs="0"/>
                <xsd:element name="outputPorts" type="outputPortsType"
                             minOccurs="0"/>
                <xsd:element name="components" type="LFBComponentsType"
                             minOccurs="0"/>
                <xsd:element name="capabilities"
                             type="LFBCapabilitiesType" minOccurs="0"/>
                <xsd:element name="events"
                             type="eventsType" minOccurs="0"/>
                <xsd:element ref="description" minOccurs="0"/>
              </xsd:sequence>



Halpern & Hadi Salim         Standards Track                   [Page 92]


RFC 5812                     ForCES FE Model                  March 2010


              <xsd:attribute name="LFBClassID" use="required"
                             type="xsd:unsignedInt"/>
            </xsd:complexType>
            <!-- Key constraint to ensure unique attribute names within
                 a class:
            -->
            <xsd:key name="components">
              <xsd:selector xpath="lfb:components/lfb:component"/>
              <xsd:field xpath="lfb:name"/>
            </xsd:key>
            <xsd:key name="capabilities">
              <xsd:selector xpath="lfb:capabilities/lfb:capability"/>
              <xsd:field xpath="lfb:name"/>
            </xsd:key>
            <xsd:key name="componentIDs">
              <xsd:selector xpath="lfb:components/lfb:component"/>
              <xsd:field xpath="@componentID"/>
            </xsd:key>
            <xsd:key name="capabilityIDs">
              <xsd:selector xpath="lfb:capabilities/lfb:capability"/>
              <xsd:field xpath="@componentID"/>
            </xsd:key>
          </xsd:element>
        </xsd:sequence>
      </xsd:complexType>
    <xsd:simpleType name="versionType">
      <xsd:restriction base="xsd:NMTOKEN">
        <xsd:pattern value="[1-9][0-9]*\.([1-9][0-9]*|0)"/>
      </xsd:restriction>
    </xsd:simpleType>
    <xsd:complexType name="inputPortsType">
      <xsd:sequence>
        <xsd:element name="inputPort" type="inputPortType"
                     maxOccurs="unbounded"/>
      </xsd:sequence>
    </xsd:complexType>
    <xsd:complexType name="inputPortType">
      <xsd:sequence>
        <xsd:element name="name" type="xsd:NMTOKEN"/>
        <xsd:element ref="synopsis"/>
        <xsd:element name="expectation" type="portExpectationType"/>
        <xsd:element ref="description" minOccurs="0"/>
      </xsd:sequence>
      <xsd:attribute name="group" type="xsd:boolean" use="optional"
                     default="0"/>
    </xsd:complexType>
    <xsd:complexType name="portExpectationType">
      <xsd:sequence>



Halpern & Hadi Salim         Standards Track                   [Page 93]


RFC 5812                     ForCES FE Model                  March 2010


        <xsd:element name="frameExpected" minOccurs="0">
          <xsd:complexType>
            <xsd:sequence>
            <!-- ref must refer to a name of a defined frame type -->
            <xsd:element name="ref" type="xsd:string"
                           maxOccurs="unbounded"/>
            </xsd:sequence>
          </xsd:complexType>
        </xsd:element>
        <xsd:element name="metadataExpected" minOccurs="0">
          <xsd:complexType>
            <xsd:choice maxOccurs="unbounded">
              <!-- ref must refer to a name of a defined metadata -->

              <xsd:element name="ref" type="metadataInputRefType"/>
              <xsd:element name="one-of"
                           type="metadataInputChoiceType"/>
            </xsd:choice>
          </xsd:complexType>
        </xsd:element>
      </xsd:sequence>
    </xsd:complexType>
    <xsd:complexType name="metadataInputChoiceType">
      <xsd:choice minOccurs="2" maxOccurs="unbounded">
        <!-- ref must refer to a name of a defined metadata -->
        <xsd:element name="ref" type="xsd:NMTOKEN"/>
        <xsd:element name="one-of" type="metadataInputChoiceType"/>
        <xsd:element name="metadataSet" type="metadataInputSetType"/>
      </xsd:choice>
    </xsd:complexType>
    <xsd:complexType name="metadataInputSetType">
      <xsd:choice minOccurs="2" maxOccurs="unbounded">
        <!-- ref must refer to a name of a defined metadata -->
        <xsd:element name="ref" type="metadataInputRefType"/>
        <xsd:element name="one-of" type="metadataInputChoiceType"/>
      </xsd:choice>
    </xsd:complexType>
    <xsd:complexType name="metadataInputRefType">
      <xsd:simpleContent>
        <xsd:extension base="xsd:NMTOKEN">
          <xsd:attribute name="dependency" use="optional"
                         default="required">
            <xsd:simpleType>
              <xsd:restriction base="xsd:string">
                <xsd:enumeration value="required"/>
                <xsd:enumeration value="optional"/>
              </xsd:restriction>
            </xsd:simpleType>



Halpern & Hadi Salim         Standards Track                   [Page 94]


RFC 5812                     ForCES FE Model                  March 2010


          </xsd:attribute>
          <xsd:attribute name="defaultValue" type="xsd:token"
                         use="optional"/>
        </xsd:extension>
      </xsd:simpleContent>
    </xsd:complexType>
    <xsd:complexType name="outputPortsType">
      <xsd:sequence>
        <xsd:element name="outputPort" type="outputPortType"
                     maxOccurs="unbounded"/>
      </xsd:sequence>
    </xsd:complexType>
    <xsd:complexType name="outputPortType">
      <xsd:sequence>
        <xsd:element name="name" type="xsd:NMTOKEN"/>
        <xsd:element ref="synopsis"/>
        <xsd:element name="product" type="portProductType"/>
        <xsd:element ref="description" minOccurs="0"/>
      </xsd:sequence>
      <xsd:attribute name="group" type="xsd:boolean" use="optional"
                     default="0"/>
    </xsd:complexType>
    <xsd:complexType name="portProductType">
      <xsd:sequence>
        <xsd:element name="frameProduced">
         <xsd:complexType>
            <xsd:sequence>
              <!-- ref must refer to a name of a defined frame type
                   -->
                  <xsd:element name="ref" type="xsd:NMTOKEN"
                             maxOccurs="unbounded"/>
              </xsd:sequence>
            </xsd:complexType>
          </xsd:element>
          <xsd:element name="metadataProduced" minOccurs="0">
            <xsd:complexType>
              <xsd:choice maxOccurs="unbounded">
                <!-- ref must refer to a name of a defined metadata
                -->
                <xsd:element name="ref" type="metadataOutputRefType"/>
                <xsd:element name="one-of"
                             type="metadataOutputChoiceType"/>
              </xsd:choice>
            </xsd:complexType>
          </xsd:element>
        </xsd:sequence>
      </xsd:complexType>
      <xsd:complexType name="metadataOutputChoiceType">



Halpern & Hadi Salim         Standards Track                   [Page 95]


RFC 5812                     ForCES FE Model                  March 2010


        <xsd:choice minOccurs="2" maxOccurs="unbounded">
          <!-- ref must refer to a name of a defined metadata -->
          <xsd:element name="ref" type="xsd:NMTOKEN"/>
          <xsd:element name="one-of" type="metadataOutputChoiceType"/>
          <xsd:element name="metadataSet" type="metadataOutputSetType"/>
        </xsd:choice>
      </xsd:complexType>
      <xsd:complexType name="metadataOutputSetType">
        <xsd:choice minOccurs="2" maxOccurs="unbounded">
          <!-- ref must refer to a name of a defined metadata -->
          <xsd:element name="ref" type="metadataOutputRefType"/>
          <xsd:element name="one-of" type="metadataOutputChoiceType"/>
        </xsd:choice>
      </xsd:complexType>
      <xsd:complexType name="metadataOutputRefType">
        <xsd:simpleContent>
          <xsd:extension base="xsd:NMTOKEN">
            <xsd:attribute name="availability" use="optional"
                           default="unconditional">
              <xsd:simpleType>
                <xsd:restriction base="xsd:string">
                  <xsd:enumeration value="unconditional"/>
                  <xsd:enumeration value="conditional"/>
                </xsd:restriction>
              </xsd:simpleType>
            </xsd:attribute>
          </xsd:extension>
        </xsd:simpleContent>
      </xsd:complexType>
      <xsd:complexType name="LFBComponentsType">
        <xsd:sequence>
          <xsd:element name="component" maxOccurs="unbounded">
            <xsd:complexType>
              <xsd:sequence>
                <xsd:element name="name" type="xsd:NMTOKEN"/>
                <xsd:element ref="synopsis"/>
                <xsd:element ref="description" minOccurs="0"/>
                <xsd:element name="optional" minOccurs="0"/>
                <xsd:group ref="typeDeclarationGroup"/>
                <xsd:element name="defaultValue" type="xsd:token"
                             minOccurs="0"/>
              </xsd:sequence>
              <xsd:attribute name="access" use="optional"
                             default="read-write">
                <xsd:simpleType>
                  <xsd:list itemType="accessModeType"/>
                </xsd:simpleType>
              </xsd:attribute>



Halpern & Hadi Salim         Standards Track                   [Page 96]


RFC 5812                     ForCES FE Model                  March 2010


              <xsd:attribute name="componentID" use="required"
                             type="xsd:unsignedInt"/>
            </xsd:complexType>
          </xsd:element>
        </xsd:sequence>
      </xsd:complexType>
      <xsd:simpleType name="accessModeType">
        <xsd:restriction base="xsd:NMTOKEN">
          <xsd:enumeration value="read-only"/>
          <xsd:enumeration value="read-write"/>
          <xsd:enumeration value="write-only"/>
          <xsd:enumeration value="read-reset"/>
          <xsd:enumeration value="trigger-only"/>
        </xsd:restriction>
      </xsd:simpleType>
      <xsd:complexType name="LFBCapabilitiesType">
        <xsd:sequence>
          <xsd:element name="capability" maxOccurs="unbounded">
            <xsd:complexType>
              <xsd:sequence>
                <xsd:element name="name" type="xsd:NMTOKEN"/>
                <xsd:element ref="synopsis"/>
                <xsd:element ref="description" minOccurs="0"/>
                <xsd:element name="optional" minOccurs="0"/>
                <xsd:group ref="typeDeclarationGroup"/>
              </xsd:sequence>
              <xsd:attribute name="componentID" use="required"
                             type="xsd:integer"/>
            </xsd:complexType>
          </xsd:element>
        </xsd:sequence>
      </xsd:complexType>
      <xsd:complexType name="eventsType">
        <xsd:sequence>
          <xsd:element name="event" maxOccurs="unbounded">
            <xsd:complexType>
              <xsd:sequence>
                <xsd:element name="name" type="xsd:NMTOKEN"/>
                <xsd:element ref="synopsis"/>
                <xsd:element name="eventTarget" type="eventPathType"/>
                <xsd:element ref="eventCondition"/>
                <xsd:element name="eventReports" type="eventReportsType"
                             minOccurs="0"/>
                <xsd:element ref="description" minOccurs="0"/>
              </xsd:sequence>
              <xsd:attribute name="eventID" use="required"
                             type="xsd:integer"/>
            </xsd:complexType>



Halpern & Hadi Salim         Standards Track                   [Page 97]


RFC 5812                     ForCES FE Model                  March 2010


          </xsd:element>
        </xsd:sequence>
        <xsd:attribute name="baseID" type="xsd:integer"
                       use="optional"/>
      </xsd:complexType>
      <!-- the substitution group for the event conditions -->
      <xsd:element name="eventCondition" abstract="true"/>
      <xsd:element name="eventCreated"
                  substitutionGroup="eventCondition"/>
      <xsd:element name="eventDeleted"
                  substitutionGroup="eventCondition"/>
      <xsd:element name="eventChanged"
                  substitutionGroup="eventCondition"/>
      <xsd:element name="eventGreaterThan"
                  substitutionGroup="eventCondition"/>
      <xsd:element name="eventLessThan"
                  substitutionGroup="eventCondition"/>
      <xsd:complexType name="eventPathType">
        <xsd:sequence>
          <xsd:element ref="eventPathPart" maxOccurs="unbounded"/>
        </xsd:sequence>
      </xsd:complexType>
      <!-- the substitution group for the event path parts -->
      <xsd:element name="eventPathPart" type="xsd:string"
                   abstract="true"/>
      <xsd:element name="eventField" type="xsd:string"
                   substitutionGroup="eventPathPart"/>
      <xsd:element name="eventSubscript" type="xsd:string"
                   substitutionGroup="eventPathPart"/>
      <xsd:complexType name="eventReportsType">
        <xsd:sequence>
          <xsd:element name="eventReport" type="eventPathType"
                       maxOccurs="unbounded"/>
        </xsd:sequence>
      </xsd:complexType>
      <xsd:simpleType name="booleanType">
        <xsd:restriction base="xsd:string">
          <xsd:enumeration value="0"/>
          <xsd:enumeration value="1"/>
        </xsd:restriction>
      </xsd:simpleType>
      </xsd:schema>









Halpern & Hadi Salim         Standards Track                   [Page 98]


RFC 5812                     ForCES FE Model                  March 2010


5.  FE Components and Capabilities

   A ForCES forwarding element handles traffic on behalf of a ForCES
   control element.  While the standards will describe the protocol and
   mechanisms for this control, different implementations and different
   instances will have different capabilities.  The CE MUST be able to
   determine what each instance it is responsible for is actually
   capable of doing.  As stated previously, this is an approximation.
   The CE is expected to be prepared to cope with errors in requests and
   variations in detail not captured by the capabilities information
   about an FE.

   In addition to its capabilities, an FE will have information that can
   be used in understanding and controlling the forwarding operations.
   Some of this information will be read-only, while others parts may
   also be writeable.

   In order to make the FE information easily accessible, the
   information is represented in an LFB.  This LFB has a class,
   FEObject.  The LFBClassID for this class is 1.  Only one instance of
   this class will ever be present in an FE, and the instance ID of that
   instance in the protocol is 1.  Thus, by referencing the components
   of class:1, instance:1 a CE can get the general information about the
   FE.  The FEObject LFB class is described in this section.

   There will also be an FEProtocol LFB class.  LFBClassID 2 is reserved
   for that class.  There will be only one instance of that class as
   well.  Details of that class are defined in the ForCES protocol
   [RFC5810] document.

5.1.   XML for FEObject Class Definition

          <?xml version="1.0" encoding="UTF-8"?>
          <LFBLibrary xmlns="urn:ietf:params:xml:ns:forces:lfbmodel:1.0"
            xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
            provides="FEObject">
            <dataTypeDefs>
              <dataTypeDef>
                <name>LFBAdjacencyLimitType</name>
                <synopsis>Describing the Adjacent LFB</synopsis>
                <struct>
                  <component componentID="1">
                    <name>NeighborLFB</name>
                    <synopsis>ID for that LFB class</synopsis>
                    <typeRef>uint32</typeRef>
                  </component>
                  <component componentID="2">
                    <name>ViaPorts</name>



Halpern & Hadi Salim         Standards Track                   [Page 99]


RFC 5812                     ForCES FE Model                  March 2010


                    <synopsis>
                      the ports on which we can connect
                    </synopsis>
                    <array type="variable-size">
                      <typeRef>string</typeRef>
                    </array>
                  </component>
                </struct>
              </dataTypeDef>
              <dataTypeDef>
                <name>PortGroupLimitType</name>
                <synopsis>
                  Limits on the number of ports in a given group
                </synopsis>
                <struct>
                  <component componentID="1">
                    <name>PortGroupName</name>
                    <synopsis>Group Name</synopsis>
                    <typeRef>string</typeRef>
                  </component>
                  <component componentID="2">
                    <name>MinPortCount</name>
                    <synopsis>Minimum Port Count</synopsis>
                    <optional/>
                    <typeRef>uint32</typeRef>
                  </component>
                  <component componentID="3">
                    <name>MaxPortCount</name>
                    <synopsis>Max Port Count</synopsis>
                    <optional/>
                    <typeRef>uint32</typeRef>
                  </component>
                </struct>
              </dataTypeDef>
              <dataTypeDef>
                <name>SupportedLFBType</name>
                <synopsis>table entry for supported LFB</synopsis>
                <struct>
                  <component componentID="1">
                    <name>LFBName</name>
                    <synopsis>
                      The name of a supported LFB class
                    </synopsis>
                    <typeRef>string</typeRef>
                  </component>
                  <component componentID="2">
                    <name>LFBClassID</name>
                    <synopsis>the id of a supported LFB class</synopsis>



Halpern & Hadi Salim         Standards Track                  [Page 100]


RFC 5812                     ForCES FE Model                  March 2010


                    <typeRef>uint32</typeRef>
                  </component>
                  <component componentID="3">
                    <name>LFBVersion</name>
                    <synopsis>
                      The version of the LFB class used
                      by this FE.
                    </synopsis>
                    <typeRef>string</typeRef>
                  </component>
                  <component componentID="4">
                    <name>LFBOccurrenceLimit</name>
                    <synopsis>
                      the upper limit of instances of LFBs of this class
                    </synopsis>
                    <optional/>
                    <typeRef>uint32</typeRef>
                  </component>
                  <!-- For each port group, how many ports can exist
                  -->
                  <component componentID="5">
                    <name>PortGroupLimits</name>
                    <synopsis>Table of Port Group Limits</synopsis>
                    <optional/>
                    <array type="variable-size">
                      <typeRef>PortGroupLimitType</typeRef>
                    </array>
                  </component>
        <!-- for the named LFB Class, the LFB Classes it may follow -->
                  <component componentID="6">
                    <name>CanOccurAfters</name>
                    <synopsis>
                      List of LFB classes that this LFB class can follow
                    </synopsis>
                    <optional/>
                    <array type="variable-size">
                      <typeRef>LFBAdjacencyLimitType</typeRef>
                    </array>
                  </component>
        <!-- for the named LFB Class, the LFB Classes that may follow it
          -->
                  <component componentID="7">
                    <name>CanOccurBefores</name>
                    <synopsis>
                      List of LFB classes that can follow this LFB class
                    </synopsis>
                    <optional/>
                    <array type="variable-size">



Halpern & Hadi Salim         Standards Track                  [Page 101]


RFC 5812                     ForCES FE Model                  March 2010


                      <typeRef>LFBAdjacencyLimitType</typeRef>
                    </array>
                  </component>
                  <component componentID="8">
                    <name>UseableParentLFBClasses</name>
                    <synopsis>
                      List of LFB classes from which this class has
                      inherited, and which the FE is willing to allow
                      for references to instances of this class.
                    </synopsis>
                    <optional/>
                    <array type="variable-size">
                      <typeRef>uint32</typeRef>
                    </array>
                  </component>
                </struct>
              </dataTypeDef>
              <dataTypeDef>
                <name>FEStateValues</name>
                <synopsis>The possible values of status</synopsis>
                <atomic>
                  <baseType>uchar</baseType>
                  <specialValues>
                    <specialValue value="0">
                      <name>AdminDisable</name>
                      <synopsis>
                        FE is administratively disabled
                    </synopsis>
                    </specialValue>
                    <specialValue value="1">
                      <name>OperDisable</name>
                      <synopsis>FE is operatively disabled</synopsis>
                    </specialValue>
                    <specialValue value="2">
                      <name>OperEnable</name>
                      <synopsis>FE is operating</synopsis>
                    </specialValue>
                  </specialValues>
                </atomic>
              </dataTypeDef>
              <dataTypeDef>
                <name>FEConfiguredNeighborType</name>
                <synopsis>Details of the FE's Neighbor</synopsis>
                <struct>
                  <component componentID="1">
                    <name>NeighborID</name>
                    <synopsis>Neighbors FEID</synopsis>
                    <typeRef>uint32</typeRef>



Halpern & Hadi Salim         Standards Track                  [Page 102]


RFC 5812                     ForCES FE Model                  March 2010


                  </component>
                  <component componentID="2">
                    <name>InterfaceToNeighbor</name>
                    <synopsis>
                      FE's interface that connects to this neighbor
                    </synopsis>
                    <optional/>
                    <typeRef>string</typeRef>
                  </component>
                  <component componentID="3">
                    <name>NeighborInterface</name>
                    <synopsis>
                      The name of the interface on the neighbor to
                      which this FE is adjacent.  This is required
                      in case two FEs are adjacent on more than
                      one interface.
                    </synopsis>
                    <optional/>
                    <typeRef>string</typeRef>
                  </component>
                </struct>
              </dataTypeDef>
              <dataTypeDef>
                <name>LFBSelectorType</name>
                <synopsis>
                  Unique identification of an LFB class-instance
                </synopsis>
                <struct>
                  <component componentID="1">
                    <name>LFBClassID</name>
                    <synopsis>LFB Class Identifier</synopsis>
                    <typeRef>uint32</typeRef>
                  </component>
                  <component componentID="2">
                    <name>LFBInstanceID</name>
                    <synopsis>LFB Instance ID</synopsis>
                    <typeRef>uint32</typeRef>
                  </component>
                </struct>
              </dataTypeDef>
              <dataTypeDef>
                <name>LFBLinkType</name>
                <synopsis>
                  Link between two LFB instances of topology
                </synopsis>
                <struct>
                  <component componentID="1">
                    <name>FromLFBID</name>



Halpern & Hadi Salim         Standards Track                  [Page 103]


RFC 5812                     ForCES FE Model                  March 2010


                    <synopsis>LFB src</synopsis>
                    <typeRef>LFBSelectorType</typeRef>
                  </component>
                  <component componentID="2">
                    <name>FromPortGroup</name>
                    <synopsis>src port group</synopsis>
                    <typeRef>string</typeRef>
                  </component>
                  <component componentID="3">
                    <name>FromPortIndex</name>
                    <synopsis>src port index</synopsis>
                    <typeRef>uint32</typeRef>
                  </component>
                  <component componentID="4">
                    <name>ToLFBID</name>
                    <synopsis>dst LFBID</synopsis>
                    <typeRef>LFBSelectorType</typeRef>
                  </component>
                  <component componentID="5">
                    <name>ToPortGroup</name>
                    <synopsis>dst port group</synopsis>
                    <typeRef>string</typeRef>
                  </component>
                  <component componentID="6">
                    <name>ToPortIndex</name>
                    <synopsis>dst port index</synopsis>
                    <typeRef>uint32</typeRef>
                  </component>
                </struct>
              </dataTypeDef>
            </dataTypeDefs>
            <LFBClassDefs>
              <LFBClassDef LFBClassID="1">
                <name>FEObject</name>
                <synopsis>Core LFB: FE Object</synopsis>
                <version>1.0</version>
                <components>
                  <component access="read-write" componentID="1">
                    <name>LFBTopology</name>
                    <synopsis>the table of known Topologies</synopsis>
                    <array type="variable-size">
                      <typeRef>LFBLinkType</typeRef>
                    </array>
                  </component>
                  <component access="read-write" componentID="2">
                    <name>LFBSelectors</name>
                    <synopsis>
                       table of known active LFB classes and



Halpern & Hadi Salim         Standards Track                  [Page 104]


RFC 5812                     ForCES FE Model                  March 2010


                       instances
                    </synopsis>
                    <array type="variable-size">
                      <typeRef>LFBSelectorType</typeRef>
                    </array>
                  </component>
                  <component access="read-write" componentID="3">
                    <name>FEName</name>
                    <synopsis>name of this FE</synopsis>
                    <typeRef>string[40]</typeRef>
                  </component>
                  <component access="read-write" componentID="4">
                    <name>FEID</name>
                    <synopsis>ID of this FE</synopsis>
                    <typeRef>uint32</typeRef>
                  </component>
                  <component access="read-only" componentID="5">
                    <name>FEVendor</name>
                    <synopsis>vendor of this FE</synopsis>
                    <typeRef>string[40]</typeRef>
                  </component>
                  <component access="read-only" componentID="6">
                    <name>FEModel</name>
                    <synopsis>model of this FE</synopsis>
                    <typeRef>string[40]</typeRef>
                  </component>
                  <component access="read-only" componentID="7">
                    <name>FEState</name>
                    <synopsis>State of this FE</synopsis>
                    <typeRef>FEStateValues</typeRef>
                  </component>
                  <component access="read-write" componentID="8">
                    <name>FENeighbors</name>
                    <synopsis>table of known neighbors</synopsis>
                    <optional/>
                    <array type="variable-size">
                      <typeRef>FEConfiguredNeighborType</typeRef>
                    </array>
                  </component>
                </components>
                <capabilities>
                  <capability componentID="30">
                    <name>ModifiableLFBTopology</name>
                    <synopsis>
                      Whether Modifiable LFB is supported
                    </synopsis>
                    <optional/>
                    <typeRef>boolean</typeRef>



Halpern & Hadi Salim         Standards Track                  [Page 105]


RFC 5812                     ForCES FE Model                  March 2010


                  </capability>
                  <capability componentID="31">
                    <name>SupportedLFBs</name>
                    <synopsis>List of all supported LFBs</synopsis>
                    <optional/>
                    <array type="variable-size">
                      <typeRef>SupportedLFBType</typeRef>
                    </array>
                  </capability>
                </capabilities>
              </LFBClassDef>
            </LFBClassDefs>
          </LFBLibrary>

5.2.  FE Capabilities

   The FE capability information is contained in the capabilities
   element of the class definition.  As described elsewhere, capability
   information is always considered to be read-only.

   The currently defined capabilities are ModifiableLFBTopology and
   SupportedLFBs.  Information as to which components of the FEObject
   LFB are supported is accessed by the properties information for those
   components.

5.2.1.   ModifiableLFBTopology

   This component has a boolean value that indicates whether the LFB
   topology of the FE may be changed by the CE.  If the component is
   absent, the default value is assumed to be true, and the CE presumes
   that the LFB topology may be changed.  If the value is present and
   set to false, the LFB topology of the FE is fixed.  If the topology
   is fixed, the SupportedLFBs element may be omitted, and the list of
   supported LFBs is inferred by the CE from the LFB topology
   information.  If the list of supported LFBs is provided when
   ModifiableLFBTopology is false, the CanOccurBefore and CanOccurAfter
   information should be omitted.

5.2.2.   SupportedLFBs and SupportedLFBType

   One capability that the FE should include is the list of supported
   LFB classes.  The SupportedLFBs component, is an array that contains
   the information about each supported LFB class.  The array structure
   type is defined as the SupportedLFBType dataTypeDef.

   Each entry in the SupportedLFBs array describes an LFB class that the
   FE supports.  In addition to indicating that the FE supports the
   class, FEs with modifiable LFB topology SHOULD include information



Halpern & Hadi Salim         Standards Track                  [Page 106]


RFC 5812                     ForCES FE Model                  March 2010


   about how LFBs of the specified class may be connected to other LFBs.
   This information SHOULD describe which LFB classes the specified LFB
   class may succeed or precede in the LFB topology.  The FE SHOULD
   include information as to which port groups may be connected to the
   given adjacent LFB class.  If port group information is omitted, it
   is assumed that all port groups may be used.  This capability
   information on the acceptable ordering and connection of LFBs MAY be
   omitted if the implementor concludes that the actual constraints are
   such that the information would be misleading for the CE.

5.2.2.1.  LFBName

   This component has as its value the name of the LFB class being
   described.

5.2.2.2.  LFBClassID

   LFBClassID is the numeric ID of the LFB class being described.  While
   conceptually redundant with the LFB name, both are included for
   clarity and to allow consistency checking.

5.2.2.3.  LFBVersion

   LFBVersion is the version string specifying the LFB class version
   supported by this FE.  As described above in versioning, an FE can
   support only a single version of a given LFB class.

5.2.2.4.  LFBOccurrenceLimit

   This component, if present, indicates the largest number of instances
   of this LFB class the FE can support.  For FEs that do not have the
   capability to create or destroy LFB instances, this can either be
   omitted or be the same as the number of LFB instances of this class
   contained in the LFB list attribute.

5.2.2.5.  PortGroupLimits and PortGroupLimitType

   The PortGroupLimits component is an array of information about the
   port groups supported by the LFB class.  The structure of the port
   group limit information is defined by the PortGroupLimitType
   dataTypeDef.

   Each PortGroupLimits array entry contains information describing a
   single port group of the LFB class.  Each array entry contains the
   name of the port group in the PortGroupName component, the fewest
   number of ports that can exist in the group in the MinPortCount
   component, and the largest number of ports that can exist in the
   group in the MaxPortCount component.



Halpern & Hadi Salim         Standards Track                  [Page 107]


RFC 5812                     ForCES FE Model                  March 2010


5.2.2.6.  CanOccurAfters and LFBAdjacencyLimitType

   The CanOccurAfters component is an array that contains the list of
   LFBs the described class can occur after.  The array entries are
   defined in the LFBAdjacencyLimitType dataTypeDef.

   The array entries describe a permissible positioning of the described
   LFB class, referred to here as the SupportedLFB.  Specifically, each
   array entry names an LFB that can topologically precede that LFB
   class.  That is, the SupportedLFB can have an input port connected to
   an output port of an LFB that appears in the CanOccurAfters array.
   The LFB class that the SupportedLFB can follow is identified by the
   NeighborLFB component (of the LFBAdjacencyLimitType dataTypeDef) of
   the CanOccurAfters array entry.  If this neighbor can only be
   connected to a specific set of input port groups, then the viaPort
   component is included.  This component is an array, with one entry
   for each input port group of the SupportedLFB that can be connected
   to an output port of the NeighborLFB.

   (For example, within a SupportedLFBs entry, each array entry of the
   CanOccurAfters array must have a unique NeighborLFB, and within each
   such array entry each viaPort must represent a distinct and valid
   input port group of the SupportedLFB.  The LFB class definition
   schema does not include these uniqueness constraints.)

5.2.2.7.  CanOccurBefores and LFBAdjacencyLimitType

   The CanOccurBefores array holds the information about which LFB
   classes can follow the described class.  Structurally, this element
   parallels CanOccurAfters, and uses the same type definition for the
   array entries.

   The array entries list those LFB classes that the SupportedLFB may
   precede in the topology.  In this component, the entries in the
   viaPort component of the array value represent the output port groups
   of the SupportedLFB that may be connected to the NeighborLFB.  As
   with CanOccurAfters, viaPort may have multiple entries if multiple
   output ports may legitimately connect to the given NeighborLFB class.

   (And a similar set of uniqueness constraints applies to the
   CanOccurBefore clauses, even though an LFB may occur both in
   CanOccurAfter and CanOccurBefore.)

5.2.2.8.  UseableParentLFBClasses

   The UseableParentLFBClasses array, if present, is used to hold a list
   of parent LFB class IDs.  All the entries in the list must be IDs of
   classes from which the SupportedLFB class being described has



Halpern & Hadi Salim         Standards Track                  [Page 108]


RFC 5812                     ForCES FE Model                  March 2010


   inherited (either directly or through an intermediate parent.)  (If
   an FE includes improper values in this list, improper manipulations
   by the CE are likely, and operational failures are likely.)  In
   addition, the FE, by including a given class in the last, is
   indicating to the CE that a given parent class may be used to
   manipulate an instance of this supported LFB class.

   By allowing such substitution, the FE allows for the case where an
   instantiated LFB may be of a class not known to the CE, but could
   still be manipulated.  While it is hoped that such situations are
   rare, it is desirable for this to be supported.  This can occur if an
   FE locally defines certain LFB instances, or if an earlier CE had
   configured some LFB instances.  It can also occur if the FE would
   prefer to instantiate a more recent, more specific and suitable LFB
   class rather than a common parent.

   In order to permit this, the FE MUST be more restrained in assigning
   LFB instance IDs.  Normally, instance IDs are qualified by the LFB
   class.  However, if two LFB classes share a parent, and if that
   parent is listed in the UseableParentLFBClasses for both specific LFB
   classes, then all the instances of both (or any, if multiple classes
   are listing the common parent) MUST use distinct instances.  This
   permits the FE to determine which LFB instance is intended by CE
   manipulation operations even when a parent class is used.

5.2.2.9.   LFBClassCapabilities

   While it would be desirable to include class-capability-level
   information, this is not included in the model.  While such
   information belongs in the FE Object in the supported class table,
   the contents of that information would be class specific.  The
   currently expected encoding structures for transferring information
   between the CE and FE are such that allowing completely unspecified
   information would be likely to induce parse errors.  We could specify
   that the information be encoded in an octetstring, but then we would
   have to define the internal format of that octet string.

   As there also are not currently any defined LFB class-level
   capabilities that the FE needs to report, this information is not
   present now, but may be added in a future version of the FE object.
   (This is an example of a case where versioning, rather than
   inheritance, would be needed, since the FE object must have class ID
   1 and instance ID 1 so that the protocol behavior can start by
   finding this object.)







Halpern & Hadi Salim         Standards Track                  [Page 109]


RFC 5812                     ForCES FE Model                  March 2010


5.3.  FE Components

   The <components> element is included if the class definition contains
   the definition of the components of the FE object that are not
   considered "capabilities".  Some of these components are writeable
   and some are read-only, which is determinable by examining the
   property information of the components.

5.3.1.  FEState

   This component carries the overall state of the FE.  The possible
   values are the strings AdminDisable, OperDisable, and OperEnable.
   The starting state is OperDisable, and the transition to OperEnable
   is controlled by the FE.  The CE controls the transition from
   OperEnable to/from AdminDisable.  For details, refer to the ForCES
   protocol document [RFC5810].

5.3.2.  LFBSelectors and LFBSelectorType

   The LFBSelectors component is an array of information about the LFBs
   currently accessible via ForCES in the FE.  The structure of the LFB
   information is defined by the LFBSelectorType dataTypeDef.

   Each entry in the array describes a single LFB instance in the FE.
   The array entry contains the numeric class ID of the class of the LFB
   instance and the numeric instance ID for this instance.

5.3.3.  LFBTopology and LFBLinkType

   The optional LFBTopology component contains information about each
   inter-LFB link inside the FE, where each link is described in an
   LFBLinkType dataTypeDef.  The LFBLinkType component contains
   sufficient information to identify precisely the end points of a
   link.  The FromLFBID and ToLFBID components specify the LFB instances
   at each end of the link, and MUST reference LFBs in the LFB instance
   table.  The FromPortGroup and ToPortGroup MUST identify output and
   input port groups defined in the LFB classes of the LFB instances
   identified by FromLFBID and ToLFBID.  The FromPortIndex and
   ToPortIndex components select the entries from the port groups that
   this link connects.  All links are uniquely identified by the
   FromLFBID, FromPortGroup, and FromPortIndex fields.  Multiple links
   may have the same ToLFBID, ToPortGroup, and ToPortIndex as this model
   supports fan-in of inter-LFB links but not fan-out.








Halpern & Hadi Salim         Standards Track                  [Page 110]


RFC 5812                     ForCES FE Model                  March 2010


5.3.4.   FENeighbors and FEConfiguredNeighborType

   The FENeighbors component is an array of information about manually
   configured adjacencies between this FE and other FEs.  The content of
   the array is defined by the FEConfiguredNeighborType dataTypeDef.

   This array is intended to capture information that may be configured
   on the FE and is needed by the CE, where one array entry corresponds
   to each configured neighbor.  Note that this array is not intended to
   represent the results of any discovery protocols, as those will have
   their own LFBs.  This component is optional.

   While there may be many ways to configure neighbors, the FE-ID is the
   best way for the CE to correlate entities.  And the interface
   identifier (name string) is the best correlator.  The CE will be able
   to determine the IP address and media-level information about the
   neighbor from the neighbor directly.  Omitting that information from
   this table avoids the risk of incorrect double configuration.

   Information about the intended forms of exchange with a given
   neighbor is not captured here; only the adjacency information is
   included.

5.3.4.1.  NeighborID

   This is the ID in some space meaningful to the CE for the neighbor.

5.3.4.2.  InterfaceToNeighbor

   This identifies the interface through which the neighbor is reached.

5.3.4.3.  NeighborInterface

   This identifies the interface on the neighbor through which the
   neighbor is reached.  The interface identification is needed when
   either only one side of the adjacency has configuration information
   or the two FEs are adjacent on more than one interface.

6.  Satisfying the Requirements on the FE Model

   This section describes how the proposed FE model meets the
   requirements outlined in Section 5 of RFC 3654 [RFC3654].  The
   requirements can be separated into general requirements (Section 5,
   5.1 - 5.4) and the specification of the minimal set of logical
   functions that the FE model must support (Section 5.5).






Halpern & Hadi Salim         Standards Track                  [Page 111]


RFC 5812                     ForCES FE Model                  March 2010


   The general requirement on the FE model is that it be able to express
   the logical packet processing capability of the FE, through both a
   capability and a state model.  In addition, the FE model is expected
   to allow flexible implementations and be extensible to allow defining
   new logical functions.

   A major component of the proposed FE model is the Logical Functional
   Block (LFB) model.  Each distinct logical function in an FE is
   modeled as an LFB.  Operational parameters of the LFB that must be
   visible to the CE are conceptualized as LFB components.  These
   components express the capability of the FE and support flexible
   implementations by allowing an FE to specify which optional features
   are supported.  The components also indicate whether they are
   configurable by the CE for an LFB class.  Configurable components
   provide the CE some flexibility in specifying the behavior of an LFB.
   When multiple LFBs belonging to the same LFB class are instantiated
   on an FE, each of those LFBs could be configured with different
   component settings.  By querying the settings of the components for
   an instantiated LFB, the CE can determine the state of that LFB.

   Instantiated LFBs are interconnected in a directed graph that
   describes the ordering of the functions within an FE.  This directed
   graph is described by the topology model.  The combination of the
   components of the instantiated LFBs and the topology describe the
   packet processing functions available on the FE (current state).

   Another key component of the FE model is the FE components.  The FE
   components are used mainly to describe the capabilities of the FE,
   but they also convey information about the FE state.

   The FE model includes only the definition of the FE Object LFB
   itself.  Meeting the full set of working group requirements requires
   other LFBs.  The class definitions for those LFBs will be provided in
   other documents.

7.  Using the FE Model in the ForCES Protocol

   The actual model of the forwarding plane in a given NE is something
   the CE must learn and control by communicating with the FEs (or by
   other means).  Most of this communication will happen in the post-
   association phase using the ForCES protocol.  The following types of
   information must be exchanged between CEs and FEs via the ForCES
   protocol [RFC5810]:

   1.  FE topology query,

   2.  FE capability declaration,




Halpern & Hadi Salim         Standards Track                  [Page 112]


RFC 5812                     ForCES FE Model                  March 2010


   3.  LFB topology (per FE) and configuration capabilities query,

   4.  LFB capability declaration,

   5.  State query of LFB components,

   6.  Manipulation of LFB components, and

   7.  LFB topology reconfiguration.

   Items 1 through 5 are query exchanges, where the main flow of
   information is from the FEs to the CEs.  Items 1 through 4 are
   typically queried by the CE(s) in the beginning of the post-
   association (PA) phase, though they may be repeatedly queried at any
   time in the PA phase.  Item 5 (state query) will be used at the
   beginning of the PA phase, and often frequently during the PA phase
   (especially for the query of statistical counters).

   Items 6 and 7 are "command" types of exchanges, where the main flow
   of information is from the CEs to the FEs.  Messages in Item 6 (the
   LFB re-configuration commands) are expected to be used frequently.
   Item 7 (LFB topology re-configuration) is needed only if dynamic LFB
   topologies are supported by the FEs and it is expected to be used
   infrequently.

   The inter-FE topology (Item 1 above) can be determined by the CE in
   many ways.  Neither this document nor the ForCES protocol [RFC5810]
   document mandates a specific mechanism.  The LFB class definition
   does include the capability for an FE to be configured with, and to
   provide to the CE in response to a query, the identity of its
   neighbors.  There may also be defined specific LFB classes and
   protocols for neighbor discovery.  Routing protocols may be used by
   the CE for adjacency determination.  The CE may be configured with
   the relevant information.

   The relationship between the FE model and the seven post-association
   messages is visualized in Figure 12:














Halpern & Hadi Salim         Standards Track                  [Page 113]


RFC 5812                     ForCES FE Model                  March 2010


                                                          +--------+
                                             ..........-->|   CE   |
                        /----\               .            +--------+
                        \____/ FE Model      .              ^    |
                        |    |................        (1),2 |    | 6, 7
                        |    |  (off-line)   .      3, 4, 5 |    |
                        \____/               .              |    v
                                             .            +--------+
                      e.g., RFCs              ..........-->|   FE   |
                                                          +--------+

   Figure 12: Relationship between the FE model and the ForCES protocol
     messages, where (1) is part of the ForCES base protocol, and the
                     rest are defined by the FE model.

   The actual encoding of these messages is defined by the ForCES
   protocol [RFC5810] document and is beyond the scope of the FE model.
   Their discussion is nevertheless important here for the following
   reasons:

   o  These PA model components have considerable impact on the FE
      model.  For example, some of the above information can be
      represented as components of the LFBs, in which case such
      components must be defined in the LFB classes.

   o  The understanding of the type of information that must be
      exchanged between the FEs and CEs can help to select the
      appropriate protocol format and the actual encoding method (such
      as XML, TLVs).

   o  Understanding the frequency of these types of messages should
      influence the selection of the protocol format (efficiency
      considerations).

   The remaining sub-sections of this section address each of the seven
   message types.















Halpern & Hadi Salim         Standards Track                  [Page 114]


RFC 5812                     ForCES FE Model                  March 2010


7.1.  FE Topology Query

   An FE may contain zero, one, or more external ingress ports.
   Similarly, an FE may contain zero, one, or more external egress
   ports.  In other words, not every FE has to contain any external
   ingress or egress interfaces.  For example, Figure 13 shows two
   cascading FEs.  FE #1 contains one external ingress interface but no
   external egress interface, while FE #2 contains one external egress
   interface but no ingress interface.  It is possible to connect these
   two FEs together via their internal interfaces to achieve the
   complete ingress-to-egress packet processing function.  This provides
   the flexibility to spread the functions across multiple FEs and
   interconnect them together later for certain applications.

   While the inter-FE communication protocol is out of scope for ForCES,
   it is up to the CE to query and understand how multiple FEs are
   inter-connected to perform a complete ingress-egress packet
   processing function, such as the one described in Figure 13.  The
   inter-FE topology information may be provided by FEs, may be hard-
   coded into CE, or may be provided by some other entity (e.g., a bus
   manager) independent of the FEs.  So while the ForCES protocol
   [RFC5810] supports FE topology query from FEs, it is optional for the
   CE to use it, assuming that the CE has other means to gather such
   topology information.

            +-----------------------------------------------------+
            |  +---------+   +------------+   +---------+         |
          input|         |   |            |   |         | output  |
         ---+->| Ingress |-->|Header      |-->|IPv4     |---------+--->+
            |  | port    |   |Decompressor|   |Forwarder| FE      |    |
            |  +---------+   +------------+   +---------+ #1      |    |
            +-----------------------------------------------------+    V
                                                                       |
                 +-----------------------<-----------------------------+
                 |
                 |    +----------------------------------------+
                 V    |  +------------+   +----------+         |
                 | input |            |   |          | output  |
                 +->--+->|Header      |-->| Egress   |---------+-->
                      |  |Compressor  |   | port     | FE      |
                      |  +------------+   +----------+ #2      |
                      +----------------------------------------+

           Figure 13: An example of two FEs connected together.







Halpern & Hadi Salim         Standards Track                  [Page 115]


RFC 5812                     ForCES FE Model                  March 2010


   Once the inter-FE topology is discovered by the CE after this query,
   it is assumed that the inter-FE topology remains static.  However, it
   is possible that an FE may go down during the NE operation, or a
   board may be inserted and a new FE activated, so the inter-FE
   topology will be affected.  It is up to the ForCES protocol to
   provide a mechanism for the CE to detect such events and deal with
   the change in FE topology.  FE topology is outside the scope of the
   FE model.

7.2.  FE Capability Declarations

   FEs will have many types of limitations.  Some of the limitations
   must be expressed to the CEs as part of the capability model.  The
   CEs must be able to query these capabilities on a per-FE basis.
   Examples are the following:

   o  Metadata passing capabilities of the FE.  Understanding these
      capabilities will help the CE to evaluate the feasibility of LFB
      topologies, and hence to determine the availability of certain
      services.

   o  Global resource query limitations (applicable to all LFBs of the
      FE).

   o  LFB supported by the FE.

   o  LFB class instantiation limit.

   o  LFB topological limitations (linkage constraint, ordering, etc.).

7.3.  LFB Topology and Topology Configurability Query

   The ForCES protocol must provide the means for the CEs to discover
   the current set of LFB instances in an FE and the interconnections
   between the LFBs within the FE.  In addition, sufficient information
   should be available to determine whether the FE supports any CE-
   initiated (dynamic) changes to the LFB topology, and if so, determine
   the allowed topologies.  Topology configurability can also be
   considered as part of the FE capability query as described in Section
   7.2.

7.4.  LFB Capability Declarations

   LFB class specifications define a generic set of capabilities.  When
   an LFB instance is implemented (instantiated) on a vendor's FE, some
   additional limitations may be introduced.  Note that we discuss only
   those limitations that are within the flexibility of the LFB class
   specification.  That is, the LFB instance will remain compliant with



Halpern & Hadi Salim         Standards Track                  [Page 116]


RFC 5812                     ForCES FE Model                  March 2010


   the LFB class specification despite these limitations.  For example,
   certain features of an LFB class may be optional, in which case it
   must be possible for the CE to determine whether or not an optional
   feature is supported by a given LFB instance.  Also, the LFB class
   definitions will probably contain very few quantitative limits (e.g.,
   size of tables), since these limits are typically imposed by the
   implementation.  Therefore, quantitative limitations should always be
   expressed by capability arguments.

   LFB instances in the model of a particular FE implementation will
   possess limitations on the capabilities defined in the corresponding
   LFB class.  The LFB class specifications must define a set of
   capability arguments, and the CE must be able to query the actual
   capabilities of the LFB instance via querying the value of such
   arguments.  The capability query will typically happen when the LFB
   is first detected by the CE.  Capabilities need not be re-queried in
   case of static limitations.  In some cases, however, some
   capabilities may change in time (e.g., as a result of adding/removing
   other LFBs, or configuring certain components of some other LFB when
   the LFBs share physical resources), in which case additional
   mechanisms must be implemented to inform the CE about the changes.

   The following two broad types of limitations will exist:

   o  Qualitative restrictions.  For example, a standardized multi-
      field classifier LFB class may define a large number of
      classification fields, but a given FE may support only a subset of
      those fields.

   o  Quantitative restrictions, such as the maximum size of tables,
      etc.

   The capability parameters that can be queried on a given LFB class
   will be part of the LFB class specification.  The capability
   parameters should be regarded as special components of the LFB.  The
   actual values of these components may, therefore, be obtained using
   the same component query mechanisms as used for other LFB components.

   Capability components are read-only arguments.  In cases where some
   implementations may allow CE modification of the value, the
   information must be represented as an operational component, not a
   capability component.

   Assuming that capabilities will not change frequently, the efficiency
   of the protocol/schema/encoding is of secondary concern.






Halpern & Hadi Salim         Standards Track                  [Page 117]


RFC 5812                     ForCES FE Model                  March 2010


   Much of this restrictive information is captured by the component
   property information, and so can be accessed uniformly for all
   information within the model.

7.5.  State Query of LFB Components

   This feature must be provided by all FEs.  The ForCES protocol and
   the data schema/encoding conveyed by the protocol must together
   satisfy the following requirements to facilitate state query of the
   LFB components:

   o  Must permit FE selection.  This is primarily to refer to a single
      FE, but referring to a group of (or all) FEs may optionally be
      supported.

   o  Must permit LFB instance selection.  This is primarily to refer to
      a single LFB instance of an FE, but optionally addressing of a
      group of (or all) LFBs may be supported.

   o  Must support addressing of individual components of an LFB.

   o  Must provide efficient encoding and decoding of the addressing
      info and the configured data.

   o  Must provide efficient data transmission of the component state
      over the wire (to minimize communication load on the CE-FE link).

7.6.   LFB Component Manipulation

   The FE model provides for the definition of LFB classes.  Each class
   has a globally unique identifier.  Information within the class is
   represented as components and assigned identifiers within the scope
   of that class.  This model also specifies that instances of LFB
   classes have identifiers.  The combination of class identifiers,
   instance identifiers, and component identifiers is used by the
   protocol to reference the LFB information in the protocol operations.

7.7.  LFB Topology Reconfiguration

   Operations that will be needed to reconfigure LFB topology are as
   follows:

   o  Create a new instance of a given LFB class on a given FE.

   o  Connect a given output of LFB x to the given input of LFB y.

   o  Disconnect: remove a link between a given output of an LFB and a
      given input of another LFB.



Halpern & Hadi Salim         Standards Track                  [Page 118]


RFC 5812                     ForCES FE Model                  March 2010


   o  Delete a given LFB (automatically removing all interconnects to/
      from the LFB).

8.  Example LFB Definition

   This section contains an example LFB definition.  While some
   properties of LFBs are shown by the FE Object LFB, this endeavors to
   show how a data plane LFB might be build.  This example is a
   fictional case of an interface supporting a coarse WDM optical
   interface that carries frame relay traffic.  The statistical
   information (including error statistics) is omitted.

   Later portions of this example include references to protocol
   operations.  The operations described are operations the protocol
   needs to support.  The exact format and fields are purely
   informational here, as the ForCES protocol [RFC5810] document defines
   the precise syntax and semantics of its operations.

  <?xml version="1.0" encoding="UTF-8"?>
        <LFBLibrary xmlns="urn:ietf:params:xml:ns:forces:lfbmodel:1.0"
         xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
         provides="LaserFrameLFB">
          <frameDefs>
            <frameDef>
              <name>FRFrame</name>
              <synopsis>
                  A frame relay frame, with DLCI without
                  stuffing)
              </synopsis>
            </frameDef>
            <frameDef>
              <name>IPFrame</name>
               <synopsis>An IP Packet</synopsis>
            </frameDef>
          </frameDefs>
          <dataTypeDefs>
            <dataTypeDef>
              <name>frequencyInformationType</name>
              <synopsis>
                  Information about a single CWDM frequency
              </synopsis>
              <struct>
                <component componentID="1">
                  <name>LaserFrequency</name>
                  <synopsis>encoded frequency(channel)</synopsis>
                  <typeRef>uint32</typeRef>
                </component>
                <component componentID="2">



Halpern & Hadi Salim         Standards Track                  [Page 119]


RFC 5812                     ForCES FE Model                  March 2010


                  <name>FrequencyState</name>
                  <synopsis>state of this frequency</synopsis>
                  <typeRef>PortStatusValues</typeRef>
                </component>
                <component componentID="3">
                  <name>LaserPower</name>
                  <synopsis>current observed power</synopsis>
                  <typeRef>uint32</typeRef>
                </component>
                <component componentID="4">
                  <name>FrameRelayCircuits</name>
                  <synopsis>
                      Information about circuits on this Frequency
                  </synopsis>
                  <array>
                    <typeRef>frameCircuitsType</typeRef>
                  </array>
                </component>
              </struct>
            </dataTypeDef>
            <dataTypeDef>
              <name>frameCircuitsType</name>
              <synopsis>
                  Information about a single Frame Relay Circuit
              </synopsis>
              <struct>
                <component componentID="1">
                  <name>DLCI</name>
                  <synopsis>DLCI of the circuit</synopsis>
                  <typeRef>uint32</typeRef>
                </component>
                <component componentID="2">
                  <name>CircuitStatus</name>
                  <synopsis>state of the circuit</synopsis>
                  <typeRef>PortStatusValues</typeRef>
                </component>
                <component componentID="3">
                  <name>isLMI</name>
                  <synopsis>is this the LMI circuit</synopsis>
                  <typeRef>boolean</typeRef>
                </component>
                <component componentID="4">
                  <name>associatedPort</name>
                  <synopsis>
                      which input / output port is associated
                      with this circuit
                  </synopsis>
                  <typeRef>uint32</typeRef>



Halpern & Hadi Salim         Standards Track                  [Page 120]


RFC 5812                     ForCES FE Model                  March 2010


                </component>
              </struct>
            </dataTypeDef>
            <dataTypeDef>
              <name>PortStatusValues</name>
              <synopsis>
                  The possible values of status.  Used for both
                  administrative and operational status
              </synopsis>
              <atomic>
                <baseType>uchar</baseType>
                <specialValues>
                  <specialValue value="0">
                    <name>Disabled </name>
                    <synopsis>the component is disabled</synopsis>
                  </specialValue>
                  <specialValue value="1">
                    <name>Enabled</name>
                    <synopsis>FE is operatively enabled</synopsis>
                  </specialValue>
                </specialValues>
              </atomic>
            </dataTypeDef>
          </dataTypeDefs>
          <metadataDefs>
            <metadataDef>
              <name>DLCI</name>
              <synopsis>The DLCI the frame arrived on</synopsis>
              <metadataID>12</metadataID>
              <typeRef>uint32</typeRef>
            </metadataDef>
            <metadataDef>
              <name>LaserChannel</name>
              <synopsis>The index of the laser channel</synopsis>
              <metadataID>34</metadataID>
              <typeRef>uint32</typeRef>
            </metadataDef>
          </metadataDefs>
          <LFBClassDefs>
              <!-- dummy classid, but needs to be a valid value -->
            <LFBClassDef LFBClassID="255">
              <name>FrameLaserLFB</name>
              <synopsis>Fictional LFB for Demonstrations</synopsis>
              <version>1.0</version>
              <inputPorts>
                <inputPort group="true">
                  <name>LMIfromFE</name>
                  <synopsis>



Halpern & Hadi Salim         Standards Track                  [Page 121]


RFC 5812                     ForCES FE Model                  March 2010


                      Ports for LMI traffic, for transmission
                  </synopsis>
                  <expectation>
                    <frameExpected>
                      <ref>FRFrame</ref>
                    </frameExpected>
                    <metadataExpected>
                      <ref>DLCI</ref>
                      <ref>LaserChannel</ref>
                    </metadataExpected>
                  </expectation>
                </inputPort>
                <inputPort>
                  <name>DatafromFE</name>
                  <synopsis>
                      Ports for data to be sent on circuits
                  </synopsis>
                  <expectation>
                    <frameExpected>
                      <ref>IPFrame</ref>
                    </frameExpected>
                    <metadataExpected>
                      <ref>DLCI</ref>
                      <ref>LaserChannel</ref>
                    </metadataExpected>
                  </expectation>
                </inputPort>
              </inputPorts>
              <outputPorts>
                <outputPort group="true">
                  <name>LMItoFE</name>
                  <synopsis>
                      Ports for LMI traffic for processing
                  </synopsis>
                  <product>
                    <frameProduced>
                      <ref>FRFrame</ref>
                    </frameProduced>
                    <metadataProduced>
                      <ref>DLCI</ref>
                      <ref>LaserChannel</ref>
                    </metadataProduced>
                  </product>
                </outputPort>
                <outputPort group="true">
                  <name>DatatoFE</name>
                  <synopsis>
                      Ports for Data traffic for processing



Halpern & Hadi Salim         Standards Track                  [Page 122]


RFC 5812                     ForCES FE Model                  March 2010


                  </synopsis>
                  <product>
                    <frameProduced>
                      <ref>IPFrame</ref>
                    </frameProduced>
                    <metadataProduced>
                      <ref>DLCI</ref>
                      <ref>LaserChannel</ref>
                    </metadataProduced>
                  </product>
                </outputPort>
              </outputPorts>
              <components>
                <component access="read-write" componentID="1">
                  <name>AdminPortState</name>
                  <synopsis>is this port allowed to function</synopsis>
                  <typeRef>PortStatusValues</typeRef>
                </component>
                <component access="read-write" componentID="2">
                  <name>FrequencyInformation</name>
                  <synopsis>
                      table of information per CWDM frequency
                  </synopsis>
                  <array type="variable-size">
                    <typeRef>frequencyInformationType</typeRef>
                  </array>
                </component>
              </components>
              <capabilities>
                <capability componentID="31">
                  <name>OperationalState</name>
                  <synopsis>
                      whether the port over all is operational
                  </synopsis>
                  <typeRef>PortStatusValues</typeRef>
                </capability>
                <capability componentID="32">
                  <name>MaximumFrequencies</name>
                  <synopsis>
                      how many laser frequencies are there
                  </synopsis>
                  <typeRef>uint16</typeRef>
                </capability>
                <capability componentID="33">
                  <name>MaxTotalCircuits</name>
                  <synopsis>
                      Total supportable Frame Relay Circuits, across
                      all laser frequencies



Halpern & Hadi Salim         Standards Track                  [Page 123]


RFC 5812                     ForCES FE Model                  March 2010


                  </synopsis>
                  <optional/>
                  <typeRef>uint32</typeRef>
                </capability>
              </capabilities>
              <events baseID="61">
                <event eventID="1">
                  <name>FrequencyState</name>
                  <synopsis>
                      The state of a frequency has changed
                  </synopsis>
                  <eventTarget>
                    <eventField>FrequencyInformation</eventField>
                    <eventSubscript>_FrequencyIndex_</eventSubscript>
                    <eventField>FrequencyState</eventField>
                  </eventTarget>
                  <eventChanged/>
                  <eventReports>
                      <!-- report the new state -->
                    <eventReport>
                      <eventField>FrequencyInformation</eventField>
                      <eventSubscript>_FrequencyIndex_</eventSubscript>
                      <eventField>FrequencyState</eventField>
                    </eventReport>
                  </eventReports>
                </event>
                <event eventID="2">
                  <name>CreatedFrequency</name>
                  <synopsis>A new frequency has appeared</synopsis>
                  <eventTarget>
                    <eventField>FrequencyInformation></eventField>
                    <eventSubscript>_FrequencyIndex_</eventSubscript>
                  </eventTarget>
                  <eventCreated/>
                  <eventReports>
                    <eventReport>
                      <eventField>FrequencyInformation</eventField>
                      <eventSubscript>_FrequencyIndex_</eventSubscript>
                      <eventField>LaserFrequency</eventField>
                    </eventReport>
                  </eventReports>
                </event>
                <event eventID="3">
                  <name>DeletedFrequency</name>
                  <synopsis>
                      A frequency Table entry has been deleted
                  </synopsis>
                  <eventTarget>



Halpern & Hadi Salim         Standards Track                  [Page 124]


RFC 5812                     ForCES FE Model                  March 2010


                    <eventField>FrequencyInformation</eventField>
                    <eventSubscript>_FrequencyIndex_</eventSubscript>
                  </eventTarget>
                  <eventDeleted/>
                 </event>
                <event eventID="4">
                  <name>PowerProblem</name>
                  <synopsis>
                      there are problems with the laser power level
                  </synopsis>
                  <eventTarget>
                    <eventField>FrequencyInformation</eventField>
                    <eventSubscript>_FrequencyIndex_</eventSubscript>
                    <eventField>LaserPower</eventField>
                  </eventTarget>
                  <eventLessThan/>
                  <eventReports>
                    <eventReport>
                      <eventField>FrequencyInformation</eventField>
                      <eventSubscript>_FrequencyIndex_</eventSubscript>
                      <eventField>LaserPower</eventField>
                    </eventReport>
                    <eventReport>
                      <eventField>FrequencyInformation</eventField>
                      <eventSubscript>_FrequencyIndex_</eventSubscript>
                      <eventField>LaserFrequency</eventField>
                    </eventReport>
                  </eventReports>
                </event>
                <event eventID="5">
                  <name>FrameCircuitChanged</name>
                  <synopsis>
                      the state of an Fr circuit on a frequency
                      has changed
                  </synopsis>
                  <eventTarget>
                    <eventField>FrequencyInformation</eventField>
                    <eventSubscript>_FrequencyIndex_</eventSubscript>
                    <eventField>FrameRelayCircuits</eventField>
                    <eventSubscript>FrameCircuitIndex</eventSubscript>
                    <eventField>CircuitStatus</eventField>
                  </eventTarget>
                  <eventChanged/>
                  <eventReports>
                    <eventReport>
                      <eventField>FrequencyInformation</eventField>
                      <eventSubscript>_FrequencyIndex_</eventSubscript>
                      <eventField>FrameRelayCircuits</eventField>



Halpern & Hadi Salim         Standards Track                  [Page 125]


RFC 5812                     ForCES FE Model                  March 2010


                      <eventSubscript>FrameCircuitIndex</eventSubscript>
                      <eventField>CircuitStatus</eventField>
                    </eventReport>
                    <eventReport>
                      <eventField>FrequencyInformation</eventField>
                      <eventSubscript>_FrequencyIndex_</eventSubscript>
                      <eventField>FrameRelayCircuits</eventField>
                      <eventSubscript>FrameCircuitIndex</eventSubscript>
                      <eventField>DLCI</eventField>
                    </eventReport>
                  </eventReports>
                </event>
              </events>
            </LFBClassDef>
          </LFBClassDefs>
        </LFBLibrary>

8.1.  Data Handling

   This LFB is designed to handle data packets coming in from or going
   out to the external world.  It is not a full port, and it lacks many
   useful statistics, but it serves to show many of the relevant
   behaviors.  The following paragraphs describe a potential operational
   device and how it might use this LFB definition.

   Packets arriving without error from the physical interface come in on
   a frame relay DLCI on a laser channel.  These two values are used by
   the LFB to look up the handling for the packet.  If the handling
   indicates that the packet is LMI, then the output index is used to
   select an LFB port from the LMItoFE port group.  The packet is sent
   as a full frame relay frame (without any bit or byte stuffing) on the
   selected port.  The laser channel and DLCI are sent as metadata, even
   though the DLCI is also still in the packet.

   Good packets that arrive and are not LMI and have a frame relay type
   indicator of IP are sent as IP packets on the port in the DatatoFE
   port group, using the same index field from the table based on the
   laser channel and DLCI.  The channel and DLCI are attached as
   metadata for other use (classifiers, for example).

   The current definition does not specify what to do if the frame relay
   type information is not IP.

   Packets arriving on input ports arrive with the laser channel and
   frame relay DLCI as metadata.  As such, a single input port could
   have been used.  With the structure that is defined (which parallels
   the output structure), the selection of channel and DLCI could be
   restricted by the arriving input port group (LMI vs. data) and port



Halpern & Hadi Salim         Standards Track                  [Page 126]


RFC 5812                     ForCES FE Model                  March 2010


   index.  As an alternative LFB design, the structures could require a
   1-1 relationship between DLCI and the LFB port, in which case no
   metadata would be needed.  This would however be quite complex and
   noisy.  The intermediate level of structure here allows parallelism
   between input and output, without requiring excessive ports.

8.1.1.  Setting Up a DLCI

   When a CE chooses to establish a DLCI on a specific laser channel, it
   sends a SET request directed to this LFB.  The request might look
   like

      T = SET
        T = PATH-DATA
          Path: flags = none, length = 4, path = 2, channel, 4, entryIdx
          DataRaw: DLCI, Enabled(1), false, out-idx

   which would establish the DLCI as enabled, with traffic going to a
   specific entry of the output port group DatatoFE.  (The CE would
   ensure that the output port is connected to the right place before
   issuing this request.)

   The response would confirm the creation of the specified entry.  This
   table is structured to use separate internal indices and DLCIs.  An
   alternative design could have used the DLCI as index, trading off
   complexities.

   One could also imagine that the FE has an LMI LFB.  Such an LFB would
   be connected to the LMItoFE and LMIfromFE port groups.  It would
   process LMI information.  It might be the LFB's job to set up the
   frame relay circuits.  The LMI LFB would have an alias entry that
   points to the frame relay circuits table it manages, so that it can
   manipulate those entities.

8.1.2.  Error Handling

   The LFB will receive invalid packets over the wire.  Many of these
   will simply result in incrementing counters.  The LFB designer might
   also specify some error rate measures.  This puts more work on the
   FE, but allows for more meaningful alarms.

   There may be some error conditions that should cause parts of the
   packet to be sent to the CE.  The error itself is not something that
   can cause an event in the LFB.  There are two ways this can be
   handled.






Halpern & Hadi Salim         Standards Track                  [Page 127]


RFC 5812                     ForCES FE Model                  March 2010


   One way is to define a specific component to count the error, and a
   component in the LFB to hold the required portion of the packet.  The
   component could be defined to hold the portion of the packet from the
   most recent error.  One could then define an event that occurs
   whenever the error count changes, and declare that reporting the
   event includes the LFB field with the packet portion.  For rare but
   extremely critical errors, this is an effective solution.  It ensures
   reliable delivery of the notification.  And it allows the CE to
   control if it wants the notification.

   Another approach is for the LFB to have a port that connects to a
   redirect sink.  The LFB would attach the laser channel, the DLCI, and
   the error indication as metadata, and ship the packet to the CE.

   Other aspects of error handling are discussed under events below.

8.2.  LFB Components

   This LFB is defined to have two top-level components.  One reflects
   the administrative state of the LFB.  This allows the CE to disable
   the LFB completely.

   The other component is the table of information about the laser
   channels.  It is a variable-sized array.  Each array entry contains
   an identifier for what laser frequency this entry is associated with,
   whether that frequency is operational, the power of the laser at that
   frequency, and a table of information about frame relay circuits on
   this frequency.  There is no administrative status since a CE can
   disable an entry simply by removing it.  (Frequency and laser power
   of a non-operational channel are not particularly useful.  Knowledge
   about what frequencies can be supported would be a table in the
   capabilities section.)

   The frame relay circuit information contains the DLCI, the
   operational circuit status, whether this circuit is to be treated as
   carrying LMI information, and which port in the output port group of
   the LFB traffic is to be sent to.  As mentioned above, the circuit
   index could, in some designs, be combined with the DLCI.

8.3.  Capabilities

   The capability information for this LFB includes whether the
   underlying interface is operational, how many frequencies are
   supported, and how many total circuits, across all channels, are
   permitted.  The maximum number for a given laser channel can be
   determined from the properties of the FrameRelayCircuits table.  A
   GET-PROP on path 2.channel.4 will give the CE the properties of that




Halpern & Hadi Salim         Standards Track                  [Page 128]


RFC 5812                     ForCES FE Model                  March 2010


   FrameRelayCircuits array which include the number of entries used,
   the first available entry, and the maximum number of entries
   permitted.

8.4.  Events

   This LFB is defined to be able to generate several events in which
   the CE may be interested.  There are events to report changes in
   operational state of frequencies, and the creation and deletion of
   frequency entries.  There is an event for changes in status of
   individual frame relay circuits.  So an event notification of
   61.5.3.11 would indicate that there had been a circuit status change
   on subscript 11 of the circuit table in subscript 3 of the frequency
   table.  The event report would include the new status of the circuit
   and the DLCI of the circuit.  Arguably, the DLCI is redundant, since
   the CE presumably knows the DLCI based on the circuit index.  It is
   included here to show including two pieces of information in an event
   report.

   As described above, the event declaration defines the event target,
   the event condition, and the event report content.  The event
   properties indicate whether the CE is subscribed to the event, the
   specific threshold for the event, and any filter conditions for the
   event.

   Another event shown is a laser power problem.  This event is
   generated whenever the laser falls below the specified threshold.
   Thus, a CE can register for the event of laser power loss on all
   circuits.  It would do this by:

         T = SET-PROP
           Path-TLV: flags=0, length = 2, path = 61.4
             Path-TLV: flags = property-field, length = 1, path = 2
               Content = 1 (register)
             Path-TLV: flags = property-field, length = 1, path = 3
               Content = 15 (threshold)

   This would set the registration for the event on all entries in the
   table.  It would also set the threshold for the event, causing
   reporting if the power falls below 15.  (Presumably, the CE knows
   what the scale is for power, and has chosen 15 as a meaningful
   problem level.)









Halpern & Hadi Salim         Standards Track                  [Page 129]


RFC 5812                     ForCES FE Model                  March 2010


   If a laser oscillates in power near the 15 mark, one could get a lot
   of notifications.  (If it flips back and forth between 14 and 15,
   each flip down will generate an event.)  Suppose that the CE decides
   to suppress this oscillation somewhat on laser channel 5.  It can do
   this by setting the hysteresis property on that event.  The request
   would look like:

         T = SET-PROP
           Path-TLV: flags=0, length = 3, path = 61.4.5
             Path-TLV: flags = property-field, length = 1, path = 4
               Content = 2 (hysteresis)

   Setting the hysteresis to 2 suppresses a lot of spurious
   notifications.  When the level first falls below 10, a notification
   is generated.  If the power level increases to 10 or 11, and then
   falls back below 10, an event will not be generated.  The power has
   to recover to at least 12 and fall back below 10 to generate another
   event.  One common cause of this form of oscillation is when the
   actual value is right near the border.  If it is really 9.5, tiny
   changes might flip it back and forth between 9 and 10.  A hysteresis
   level of 1 will suppress this sort of condition.  Many other events
   have oscillations that are somewhat wider, so larger hysteresis
   settings can be used with those.

9.   IANA Considerations

   The ForCES model creates the need for a unique XML namespace for
   ForCES library definition usage, and unique class names and numeric
   class identifiers.

9.1.  URN Namespace Registration

   IANA has registered a new XML namespace, as per the guidelines in RFC
   3688 [RFC3688].

   URI: The URI for this namespace is
   urn:ietf:params:xml:ns:forces:lfbmodel:1.0

   Registrant Contact: IESG

   XML: none, this is an XML namespace

9.2.  LFB Class Names and LFB Class Identifiers

   In order to have well defined ForCES LFB Classes, and well defined
   identifiers for those classes, IANA has created a registry of LFB
   class names, corresponding class identifiers, and the document that
   defines the LFB class.  The registry policy is simply first come,



Halpern & Hadi Salim         Standards Track                  [Page 130]


RFC 5812                     ForCES FE Model                  March 2010


   first served (FCFS) with regard to LFB class names.  With regard to
   LFB class identifiers, identifiers less than 65536 are reserved for
   assignment by IETF Standards-Track RFCs.  Identifiers equal to or
   above 65536, in the 32-bit class ID space, are available for
   assignment on a first come, first served basis.  All registry entries
   must be documented in a stable, publicly available form.


   Since this registry provides for FCFS allocation of a portion of the
   class identifier space, it is necessary to define rules for naming
   classes that are using that space.  As these can be defined by
   anyone, the needed rule is to keep the FCFS class names from
   colliding with IETF-defined class names.  Therefore, all FCFS class
   names MUST start with the string "Ext-".

   Table 1 tabulates the above information.

   IANA has created a registry of ForCES LFB Class Names and the
   corresponding ForCES LFB Class Identifiers, with the location of the
   definition of the ForCES LFB Class, in accordance with the rules in
   the following table.

   +----------------+------------+---------------+---------------------+
   | LFB Class Name |  LFB Class | Place Defined |     Description     |
   |                | Identifier |               |                     |
   +----------------+------------+---------------+---------------------+
   |    Reserved    |      0     |    RFC 5812   |       Reserved      |
   |                |            |               |       --------      |
   |    FE Object   |      1     |    RFC 5812   |    Defines ForCES   |
   |                |            |               |  Forwarding Element |
   |                |            |               |     information     |
   |   FE Protocol  |      2     |      [2]      |  Defines parameters |
   |     Object     |            |               |    for the ForCES   |
   |                |            |               |  protocol operation |
   |                |            |               |       --------      |
   |  IETF defined  |   3-65535  |   Standards   |  Reserved for IETF  |
   |      LFBs      |            |   Track RFCs  |     defined RFCs    |
   |                |            |               |       --------      |
   |   ForCES LFB   |   >65535   |  Any Publicly |  First Come, First  |
   |   Class names  |            |   Available   |  Served for any use |
   | beginning EXT- |            |    Document   |                     |
   +----------------+------------+---------------+---------------------+

                                  Table 1







Halpern & Hadi Salim         Standards Track                  [Page 131]


RFC 5812                     ForCES FE Model                  March 2010


10.  Authors Emeritus

   The following are the authors who were instrumental in the creation
   of earlier releases of this document.

   Ellen Delganes, Intel Corp.
   Lily Yang, Intel Corp.
   Ram Gopal, Nokia Research Center
   Alan DeKok, Infoblox, Inc.
   Zsolt Haraszti, Clovis Solutions

11.  Acknowledgments

   Many of the colleagues in our companies and participants in the
   ForCES mailing list have provided invaluable input into this work.
   Particular thanks to Evangelos Haleplidis for help getting the XML
   right.

12.  Security Considerations

   The FE model describes the representation and organization of data
   sets and components in the FEs.  The ForCES framework document
   [RFC3746] provides a comprehensive security analysis for the overall
   ForCES architecture.  For example, the ForCES protocol entities must
   be authenticated per the ForCES requirements before they can access
   the information elements described in this document via ForCES.
   Access to the information contained in the FE model is accomplished
   via the ForCES protocol, which is defined in separate documents, and
   thus the security issues will be addressed there.

13.  References

13.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC5810]  Doria, A., Ed., Hadi Salim, J., Ed., Haas, R., Ed.,
              Khosravi, H., Ed., Wang, W., Ed., Dong, L., Gopal, R., and
              J. Halpern, "Forwarding and Control Element Separation
              (ForCES) Protocol Specification", RFC 5810, March 2010.

   [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
              January 2004.

   [Schema1]  Thompson, H., Beech, D., Maloney, M., and N. Mendelsohn,
              "XML Schema Part 1: Structures", W3C REC-xmlschema-1,
              http://www.w3.org/TR/xmlshcema-1/, May 2001.



Halpern & Hadi Salim         Standards Track                  [Page 132]


RFC 5812                     ForCES FE Model                  March 2010


   [Schema2]  Biron, P. and A. Malhotra, "XML Schema Part 2: Datatypes",
              W3C REC-xmlschema-2, http://www.w3.org/TR/xmlschema-2/,
              May 2001.

13.2.  Informative References

   [RFC3654]  Khosravi, H. and T. Anderson, "Requirements for Separation
              of IP Control and Forwarding", RFC 3654, November 2003.

   [RFC3746]  Yang, L., Dantu, R., Anderson, T., and R. Gopal,
              "Forwarding and Control Element Separation (ForCES)
              Framework", RFC 3746, April 2004.

   [RFC3317]  Chan, K., Sahita, R., Hahn, S., and K. McCloghrie,
              "Differentiated Services Quality of Service Policy
              Information Base", RFC 3317, March 2003.

   [RFC3318]  Sahita, R., Hahn, S., Chan, K., and K. McCloghrie,
              "Framework Policy Information Base", RFC 3318, March 2003.

   [RFC3444]  Pras, A. and J. Schoenwaelder, "On the Difference between
              Information Models and Data Models", RFC 3444,
              January 2003.

   [RFC3470]  Hollenbeck, S., Rose, M., and L. Masinter, "Guidelines for
              the Use of Extensible Markup Language (XML)
              within IETF Protocols", BCP 70, RFC 3470, January 2003.

   [UNICODE]  Davis, M. and M. Suignard, "UNICODE Security
              Considerations",
              http://www.unicode.org/reports/tr36/tr36-3.html ,
              July 2005.



















Halpern & Hadi Salim         Standards Track                  [Page 133]


RFC 5812                     ForCES FE Model                  March 2010


Authors' Addresses

   Joel Halpern
   Self
   P.O. Box 6049
   Leesburg, VA  20178
   USA

   Phone: +1 703 371 3043
   EMail: jmh@joelhalpern.com


   Jamal Hadi Salim
   Znyx Networks
   Ottawa, Ontario
   Canada

   EMail: hadi@mojatatu.com

































Halpern & Hadi Salim         Standards Track                  [Page 134]